This is a follow up to d263438a6e, which
solved one problem (reset on disconnect) but introduced a second one (hang
in bootloader).
To solve both probles, False/False is needed for DTR/RTS for ESPxx, but
that would then block stm32 and others. Any unconditional combination of
DTR/RTS ends up blocking normal operation on some type of board or another.
A simple overview (for windows only):
DTR CTS ESP8266/ESP32 STM32/SAMD51/RP2040
unspecified unspecified Reset on disconnect OK
True False Hang in bootloader OK
False False OK No Repl
True True Reset on disconnect No Repl
False True Reset on disconnect No Repl
serial.manufacturer: wch.cn/Silicon Labs Microsoft
serial.description: USB-SERIAL CH340 / USB Serial Device
CP210x USB to UART
Bridge
The updated logic will only set the DTR/RTS signals for boards that do not
use standard Microsoft drivers (based on the manufacturer). It would also
be possible to check against a list of known driver manufactures (like
wch.cn or Silicon Labs) but this would require a list of known drivers for
all ports.
Signed-off-by: Jos Verlinde <jos_verlinde@hotmail.com>
Following other vfs_fat tests, so the test works on ports like stm32 that
only support 512-byte block size.
Signed-off-by: Damien George <damien@micropython.org>
This is a best-effort implementation of write polling. It's difficult to
do correctly because if there are multiple output streams (eg UART and USB
CDC) then some may not be writeable while others are. A full solution
should also have a return value from mp_hal_stdout_tx_strn(), returning the
number of bytes written to the stream(s). That's also hard to define.
The renesas-ra and stm32 ports already implement a similar best-effort
mechanism for write polling.
Fixes issue #11026.
Signed-off-by: Damien George <damien@micropython.org>
If a multitest calls `multitest.output_metric(...)` then that output will
be collected separately, not considered as part of the test verification
output, and instead be printed at the end. This is useful for tests that
want to output performance/timing metrics that may change from one run to
the next.
Signed-off-by: Damien George <damien@micropython.org>
Prior to this change, setting of UART parameters like parity, stop bits or
data bits did not work correctly. As suggested by @iabdalkader, adding
__DSB() fixes the problem, making sure that changes to the UART LCR_H
register are seen by the peripheral.
Note: the FIFO is already enabled in the call to uart_init(), so the call
to uart_set_fifo_enabled() is not required, but kept for visibility.
Fixes issue #10976.
This is intended to be used by the very outer caller of the VM/runtime. It
allows setting a top-level NLR handler that can be jumped to directly, in
order to forcefully abort the VM/runtime.
Enable using:
#define MICROPY_ENABLE_VM_ABORT (1)
Set up the handler at the top level using:
nlr_buf_t nlr;
nlr.ret_val = NULL;
if (nlr_push(&nlr) == 0) {
nlr_set_abort(&nlr);
// call into the VM/runtime
...
nlr_pop();
} else {
if (nlr.ret_val == NULL) {
// handle abort
...
} else {
// handle other exception that propagated to the top level
...
}
}
nlr_set_abort(NULL);
Schedule an abort, eg from an interrupt handler, using:
mp_sched_vm_abort();
Signed-off-by: Damien George <damien@micropython.org>
When iterating over os.ilistdir(), the special directories '.' and '..'
are filtered from the results. But the code inadvertently also filtered
any file/directory which happened to match '..*'. This change fixes the
filter.
Fixes issue #11032.
Signed-off-by: Jeremy Rand <jeremy@rand-family.com>
The following have been tested and are working:
- 550MHz CPU frequency
- UART REPL via ST-Link
- USB REPL and mass storage
- 3x LEDs and 1x user button
- Ethernet
Signed-off-by: Damien George <damien@micropython.org>
For builds with DEBUG=1 and MICROPY_HW_ENABLE_UART_REPL=1, calling
stdio_init_all() in main() detaches the UART input from REPL. This change
suppresses calling stdio_init_all() then.
Previously, setting MICROPY_HW_ENABLE_USBDEV to 0 caused build errors. The
change affects the nrf and samd ports as well, so MICROPY_HW_ENABLE_USBDEV
had to be explicitly enabled there.
The configuration options MICROPY_HW_ENABLE_USBDEV and
MICROPY_HW_ENABLE_UART_REPL are independent, and can be enabled or disabled
by a board.
Signed-off-by: Damien George <damien@micropython.org>
Changes in this commit:
- Add the timeout and timeout_char keyword options.
- Make uart.read() non-blocking.
- Add uart.any().
- Add ioctl MP_STREAM_POLL handling.
- Change uart.write() into non-busy waiting. uart.write() still waits until
all data has been sent, but calls MICROPY_EVENT_POLL_HOOK while waiting.
uart.write() uses DMA for transfer. One option would be to add a small
local buffer, such that transfers up to the size of the buffer could be
done without waiting.
- As a side effect to the change of uart.write(), uart.txdone() and ioctl
flush now report/wait correctly for the end of transmission.
- Change machine_hard_uart_buf_t in machine_hard_uart_obj_t to an instance
of that struct, rather than a pointer to one.
As the comment in py/obj.h says:
> Implementing this as a call rather than inline saves 8 bytes per usage.
So in order to get this savings, we need to tell the compiler to never
inline the function.
Signed-off-by: David Lechner <david@pybricks.com>
Even if boards do not have a clock crystal. In that case, the clock
quality will be very poor.
Always having machine.RTC means that the date/time can be set in a way that
is consistent with other ports.
This commit also removes the special code in modutime.c for devices without
the RTC class.
Signed-off-by: Damien George <damien@micropython.org>
Without this, building the unix port variants gives:
ports/unix/main.c:667: undefined reference to `mp_obj_is_package',
when MICROPY_ENABLE_EXTERNAL_IMPORT is 0.
Signed-off-by: Laurens Valk <laurens@pybricks.com>
The C-level printf is usually used for internal debugging prints, and a
port/board may want to redirect this somewhere other than stdout.
Signed-off-by: Damien George <damien@micropython.org>
These have the same frequency, but can have different duty cycle and
polarity.
pwm.deinit() stops all channels of a module, but does not release the
module. pwm.init() without arguments restarts all outputs.
Using extmod/machine_pwm.c for the Python bindings and the existing
softpwm.c driver, by just adding the interface.
Properties:
- Frequency range 1-3906 Hz.
- All PWM outputs run at the same frequency but can have different duty
cycles.
- Limited to the P0.x pins.
Since it uses the existing softpwm.c mechanism, it will be affected by
playing music with the music class.
This is a breaking change, making the hardware PWM on the nrf port
compatible with the other ports providing machine.PWM.
Frequency range 4Hz - ~5.4 MHz. The base clock range is 125kHz to 16 MHz,
and the divider range is 3 - 32767.
The hardware supports up to four outputs per PWM device with different duty
cycles, but only one output is (and was) supported.
Jan Hrudka
Jos Verlinde
Damien George
Sebastian Romero
David Lechner
robert-hh
Jeremy Rand
iabdalkader
pmendham
IhorNehrutsa
Christian Clauss
Laurens Valk