The connection failure diagnostic code was never updated enough for
exit nodes, so disable its misleading output when the node it picks
(incorrectly) to diagnose is only an exit node.
Fixes#1754
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
The new "tailscale up" checks previously didn't protect against
--advertise-exit-node being omitted in the case that
--advertise-routes was also provided. It wasn't done before because
there is no corresponding pref for "--advertise-exit-node"; it's a
helper flag that augments --advertise-routes. But that's an
implementation detail and we can still help users. We just have to
special case that pref and look whether the current routes include
both the v4 and v6 /0 routes.
Fixes#1767
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
This doesn't make --operator implicit (which we might do in the
future), but it at least doesn't require repeating it in the future
when it already matches $USER.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
It was getting cleared on notify.
Document that authURL is cleared on notify and add a new field that
isn't, using the new field for the JSON status.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
I've spent two days searching for a theoretical wireguard-go bug
around receive functions exiting early.
I've found many bugs, but none of the flavor we're looking for.
Restore wireguard-go's logging around starting and stopping receive functions,
so that we can definitively rule in or out this particular theory.
Signed-off-by: Josh Bleecher Snyder <josharian@gmail.com>
I see a bunch of these in some logs I'm looking at,
separated only by a few seconds.
Log the error so we can tell what's going on here.
Signed-off-by: Josh Bleecher Snyder <josharian@gmail.com>
These were getting rate-limited for nodes with many peers.
Consolate the output into single lines, which are nicer anyway.
Signed-off-by: Josh Bleecher Snyder <josharian@gmail.com>
With this change, the ipnserver's safesocket.Listen (the localhost
tcp.Listen) happens right away, before any synchronous
TUN/DNS/Engine/etc setup work, which might be slow, especially on
early boot on Windows.
Because the safesocket.Listen starts up early, that means localhost
TCP dials (the safesocket.Connect from the GUI) complete successfully
and thus the GUI avoids the MessageBox error. (I verified that
pacifies it, even without a Listener.Accept; I'd feared that Windows
localhost was maybe special and avoided the normal listener backlog).
Once the GUI can then connect immediately without errors, the various
timeouts then matter less, because the backend is no longer trying to
race against the GUI's timeout. So keep retrying on errors for a
minute, or 10 minutes if the system just booted in the past 10
minutes.
This should fix the problem with Windows 10 desktops auto-logging in
and starting the Tailscale frontend which was then showing a
MessageBox error about failing to connect to tailscaled, which was
slow coming up because the Windows networking stack wasn't up
yet. Fingers crossed.
Fixes#1313 (previously #1187, etc)
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
This change implements Windows version of install-system-daemon and
uninstall-system-daemon subcommands. When running the commands the
user will install or remove Tailscale Windows service.
Updates #1232
Signed-off-by: Alex Brainman <alex.brainman@gmail.com>
This used to not be necessary, because MagicDNS always did full proxying.
But with split DNS, we need to know which names to route to our resolver,
otherwise reverse lookups break.
This captures the entire CGNAT range, as well as our Tailscale ULA.
Signed-off-by: David Anderson <danderson@tailscale.com>
Otherwise, the existence of authoritative domains forces full
DNS proxying even when no other DNS config is present.
Signed-off-by: David Anderson <danderson@tailscale.com>
Logout used to be a no-op, so the ipnserver previously synthensized a Logout
on disconnect. Now that Logout actually invalidates the node key that was
forcing all GUI closes to log people out.
Instead, add a method to LocalBackend to specifically mean "the
Windows GUI closed, please forget all the state".
Fixestailscale/corp#1591 (ignoring the notification issues, tracked elsewhere)
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Let caller (macOS) do it so Finder progress bar can be dismissed
without races.
Updates tailscale/corp#1575
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
We were accidentally logging oldPort -> oldPort.
Log oldPort as well as c.port; if we failed to get the preferred port
in a previous rebind, oldPort might differ from c.port.
Signed-off-by: Josh Bleecher Snyder <josharian@gmail.com>
On macOS, we link the CLI into the GUI executable so it can be included in
the Mac App Store build.
You then need to run it like:
/Applications/Tailscale.app/Contents/MacOS/Tailscale <command>
But our old detection of whether you're running that Tailscale binary
in CLI mode wasn't accurate and often bit people. For instance, when
they made a typo, it then launched in GUI mode and broke their
existing GUI connection (starting a new IPNExtension) and took down
their network.
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
It used to just store received files URL-escaped on disk, but that was
a half done lazy implementation, and pushed the burden to callers to
validate and write things to disk in an unescaped way.
Instead, do all the validation in the receive handler and only
accept filenames that are UTF-8 and in the intersection of valid
names that all platforms support.
Fixestailscale/corp#1594
Signed-off-by: Brad Fitzpatrick <bradfitz@tailscale.com>
Brad Fitzpatrick
Josh Bleecher Snyder
Naman Sood
Alex Brainman
David Anderson
Maisem Ali