Tasmota/tasmota/include/tasmota_template.h

/*
  tasmota_template.h - template settings for Tasmota

  Copyright (C) 2021  Theo Arends

  This program is free software: you can redistribute it and/or modify
  it under the terms of the GNU General Public License as published by
  the Free Software Foundation, either version 3 of the License, or
  (at your option) any later version.

  This program is distributed in the hope that it will be useful,
  but WITHOUT ANY WARRANTY; without even the implied warranty of
  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  GNU General Public License for more details.

  You should have received a copy of the GNU General Public License
  along with this program.  If not, see <http://www.gnu.org/licenses/>.
*/

#ifndef _TASMOTA_TEMPLATE_H_
#define _TASMOTA_TEMPLATE_H_

// User selectable GPIO functionality
// ATTENTION: Only add at the end of this list just before GPIO_SENSOR_END
//            Then add the same name(s) in a nice location in array kGpioNiceList
enum UserSelectablePins {
  GPIO_NONE,                           // Not used
  GPIO_KEY1, GPIO_KEY1_NP, GPIO_KEY1_INV, GPIO_KEY1_INV_NP, // 4 x Button
  GPIO_SWT1, GPIO_SWT1_NP,             // 8 x User connected external switches
  GPIO_REL1, GPIO_REL1_INV,            // 8 x Relays
  GPIO_LED1, GPIO_LED1_INV,            // 4 x Leds
  GPIO_CNTR1, GPIO_CNTR1_NP,           // 4 x Counter
  GPIO_PWM1, GPIO_PWM1_INV,            // 5 x PWM
  GPIO_BUZZER, GPIO_BUZZER_INV,        // Buzzer
  GPIO_LEDLNK, GPIO_LEDLNK_INV,        // Link led
  GPIO_I2C_SCL, GPIO_I2C_SDA,          // Software I2C
  GPIO_SPI_MISO, GPIO_SPI_MOSI, GPIO_SPI_CLK, GPIO_SPI_CS, GPIO_SPI_DC,        // Hardware SPI
  GPIO_SSPI_MISO, GPIO_SSPI_MOSI, GPIO_SSPI_SCLK, GPIO_SSPI_CS, GPIO_SSPI_DC,  // Software SPI
  GPIO_BACKLIGHT,                      // Display backlight control
  GPIO_OLED_RESET,                     // OLED Display Reset
  GPIO_IRSEND, GPIO_IRRECV,            // IR interface
  GPIO_RFSEND, GPIO_RFRECV,            // RF interface
  GPIO_DHT11, GPIO_DHT22, GPIO_SI7021, GPIO_DHT11_OUT,  // DHT11, DHT21, DHT22, AM2301, AM2302, AM2321
  GPIO_DSB, GPIO_DSB_OUT,              // DS18B20 or DS18S20
  GPIO_WS2812,                         // WS2812 Led string
  GPIO_MHZ_TXD, GPIO_MHZ_RXD,          // MH-Z19 Serial interface
  GPIO_PZEM0XX_TX, GPIO_PZEM004_RX, GPIO_PZEM016_RX, GPIO_PZEM017_RX, // PZEM Serial Modbus interface
  GPIO_SAIR_TX, GPIO_SAIR_RX,          // SenseAir Serial interface
  GPIO_PMS5003_TX, GPIO_PMS5003_RX,    // Plantower PMS5003 Serial interface
  GPIO_SDS0X1_TX, GPIO_SDS0X1_RX,      // Nova Fitness SDS011 Serial interface
  GPIO_SBR_TX, GPIO_SBR_RX,            // Serial Bridge Serial interface
  GPIO_SR04_TRIG, GPIO_SR04_ECHO,      // SR04 interface
  GPIO_SDM120_TX, GPIO_SDM120_RX,      // SDM120 Serial interface
  GPIO_SDM630_TX, GPIO_SDM630_RX,      // SDM630 Serial interface
  GPIO_TM1638CLK, GPIO_TM1638DIO, GPIO_TM1638STB,  // TM1638 interface
  GPIO_MP3_DFR562,                     // RB-DFR-562, DFPlayer Mini MP3 Player
  GPIO_HX711_SCK, GPIO_HX711_DAT,      // HX711 Load Cell interface
  GPIO_TX2X_TXD_BLACK,                 // TX20/TX23 Transmission Pin
  GPIO_TUYA_TX, GPIO_TUYA_RX,          // Tuya Serial interface
  GPIO_MGC3130_XFER, GPIO_MGC3130_RESET,  // MGC3130 interface
  GPIO_RF_SENSOR,                      // Rf receiver with sensor decoding
  GPIO_AZ_TXD, GPIO_AZ_RXD,            // AZ-Instrument 7798 Serial interface
  GPIO_MAX31855CS, GPIO_MAX31855CLK, GPIO_MAX31855DO,  // MAX31855 Serial interface
  GPIO_NRG_SEL, GPIO_NRG_SEL_INV, GPIO_NRG_CF1, GPIO_HLW_CF, GPIO_HJL_CF,  // HLW8012/HJL-01/BL0937 energy monitoring
  GPIO_MCP39F5_TX, GPIO_MCP39F5_RX, GPIO_MCP39F5_RST,  // MCP39F501 Energy monitoring (Shelly2)
  GPIO_PN532_TXD, GPIO_PN532_RXD,      // PN532 NFC Serial interface
  GPIO_SM16716_CLK, GPIO_SM16716_DAT, GPIO_SM16716_SEL,  // SM16716 SELECT
  GPIO_DI, GPIO_DCKI,                  // my92x1 PWM controller
  GPIO_CSE7766_TX, GPIO_CSE7766_RX,    // CSE7766 Serial interface (S31 and Pow R2)
  GPIO_ARIRFRCV, GPIO_ARIRFSEL,        // Arilux RF Receive input
  GPIO_TXD, GPIO_RXD,                  // Serial interface
  GPIO_ROT1A, GPIO_ROT1B,              // Rotary switch
  GPIO_ADC_JOY,                        // Analog joystick
  GPIO_SSPI_MAX31865_CS1,              // MAX31865 Chip Select
  GPIO_HRE_CLOCK, GPIO_HRE_DATA,       // HR-E Water Meter
  GPIO_ADE7953_IRQ,                    // ADE7953 IRQ
  GPIO_SOLAXX1_TX, GPIO_SOLAXX1_RX,    // Solax Inverter Serial interface
  GPIO_ZIGBEE_TX, GPIO_ZIGBEE_RX,      // Zigbee Serial interface
  GPIO_RDM6300_RX,                     // RDM6300 RX
  GPIO_IBEACON_TX, GPIO_IBEACON_RX,    // HM17 IBEACON Serial interface
  GPIO_A4988_DIR, GPIO_A4988_STP, GPIO_A4988_ENA, GPIO_A4988_MS1,  // A4988 interface
  GPIO_OUTPUT_HI, GPIO_OUTPUT_LO,      // Fixed output state
  GPIO_DDS2382_TX, GPIO_DDS2382_RX,    // DDS2382 Serial interface
  GPIO_DDSU666_TX, GPIO_DDSU666_RX,    // DDSU666 Serial interface
  GPIO_SM2135_CLK, GPIO_SM2135_DAT,    // SM2135 PWM controller
  GPIO_DEEPSLEEP,                      // Kill switch for deepsleep
  GPIO_EXS_ENABLE,                     // EXS MCU Enable
  GPIO_TASMOTACLIENT_TXD, GPIO_TASMOTACLIENT_RXD,      // Client Serial interface
  GPIO_TASMOTACLIENT_RST, GPIO_TASMOTACLIENT_RST_INV,  // Client Reset
  GPIO_HPMA_RX, GPIO_HPMA_TX,          // Honeywell HPMA115S0 Serial interface
  GPIO_GPS_RX, GPIO_GPS_TX,            // GPS Serial interface
  GPIO_HM10_RX, GPIO_HM10_TX,          // HM10-BLE-Mijia-bridge Serial interface
  GPIO_LE01MR_RX, GPIO_LE01MR_TX,      // F&F LE-01MR energy meter
  GPIO_CC1101_GDO0, GPIO_CC1101_GDO2,  // CC1101 Serial interface
  GPIO_HRXL_RX,                        // Data from MaxBotix HRXL sonar range sensor
  GPIO_ELECTRIQ_MOODL_TX,              // ElectriQ iQ-wifiMOODL Serial TX
  GPIO_AS3935,                         // Franklin Lightning Sensor
  GPIO_ADC_INPUT,                      // Analog input
  GPIO_ADC_TEMP,                       // Analog Thermistor
  GPIO_ADC_LIGHT,                      // Analog Light sensor
  GPIO_ADC_BUTTON, GPIO_ADC_BUTTON_INV,  // Analog Button
  GPIO_ADC_RANGE,                      // Analog Range
  GPIO_ADC_CT_POWER,                   // ANalog Current
#ifdef ESP32
  GPIO_WEBCAM_PWDN, GPIO_WEBCAM_RESET, GPIO_WEBCAM_XCLK,  // Webcam
  GPIO_WEBCAM_SIOD, GPIO_WEBCAM_SIOC,  // Webcam I2C
  GPIO_WEBCAM_DATA,
  GPIO_WEBCAM_VSYNC, GPIO_WEBCAM_HREF, GPIO_WEBCAM_PCLK,
  GPIO_WEBCAM_PSCLK,
  GPIO_WEBCAM_HSD,
  GPIO_WEBCAM_PSRCS,
#endif
  GPIO_BOILER_OT_RX, GPIO_BOILER_OT_TX,  // OpenTherm Boiler TX pin
  GPIO_WINDMETER_SPEED,                // WindMeter speed counter pin
  GPIO_KEY1_TC,                        // Touch pin as button
  GPIO_BL0940_RX,                      // BL0940 serial interface
  GPIO_TCP_TX, GPIO_TCP_RX,            // TCP to serial bridge
#ifdef ESP32
  GPIO_ETH_PHY_POWER, GPIO_ETH_PHY_MDC, GPIO_ETH_PHY_MDIO,  // Ethernet
#endif
  GPIO_TELEINFO_RX,                    // Teleinfo telemetry data receive pin
  GPIO_TELEINFO_ENABLE,                // Teleinfo Enable Receive Pin
  GPIO_LMT01,                          // LMT01 input counting pin
  GPIO_IEM3000_TX, GPIO_IEM3000_RX,    // IEM3000 Serial interface
  GPIO_ZIGBEE_RST,                     // Zigbee reset
  GPIO_DYP_RX,
  GPIO_MIEL_HVAC_TX, GPIO_MIEL_HVAC_RX,  // Mitsubishi Electric HVAC
  GPIO_WE517_TX, GPIO_WE517_RX,        // ORNO WE517 Serial interface
  GPIO_AS608_TX, GPIO_AS608_RX,        // Serial interface AS608 / R503
  GPIO_SHELLY_DIMMER_BOOT0, GPIO_SHELLY_DIMMER_RST_INV,
  GPIO_RC522_RST,                      // RC522 reset
  GPIO_P9813_CLK, GPIO_P9813_DAT,      // P9813 Clock and Data
  GPIO_OPTION_A,                       // Specific device options to be served in code
  GPIO_FTC532,                         // FTC532 touch ctrlr serial input
  GPIO_RC522_CS,
  GPIO_NRF24_CS, GPIO_NRF24_DC,
  GPIO_ILI9341_CS, GPIO_ILI9341_DC,
  GPIO_ILI9488_CS,
  GPIO_EPAPER29_CS,
  GPIO_EPAPER42_CS,
  GPIO_SSD1351_CS,
  GPIO_RA8876_CS,
  GPIO_ST7789_CS, GPIO_ST7789_DC,
  GPIO_SSD1331_CS, GPIO_SSD1331_DC,
  GPIO_SDCARD_CS,
  GPIO_ROT1A_NP, GPIO_ROT1B_NP,        // Rotary switch
  GPIO_ADC_PH,                         // Analog PH Sensor
  GPIO_BS814_CLK, GPIO_BS814_DAT,      // Holtek BS814A2 touch ctrlr
  GPIO_WIEGAND_D0, GPIO_WIEGAND_D1,    // Wiegand Data lines
  GPIO_NEOPOOL_TX, GPIO_NEOPOOL_RX,    // Sugar Valley RS485 interface
  GPIO_SDM72_TX, GPIO_SDM72_RX,        // SDM72 Serial interface
  GPIO_TM1637CLK, GPIO_TM1637DIO,      // TM1637 interface
  GPIO_PROJECTOR_CTRL_TX, GPIO_PROJECTOR_CTRL_RX,  // LCD/DLP Projector Serial Control
  GPIO_SSD1351_DC,
  GPIO_XPT2046_CS,                     // XPT2046 SPI Chip Select
  GPIO_CSE7761_TX, GPIO_CSE7761_RX,    // CSE7761 Serial interface (Dual R3)
  GPIO_VL53LXX_XSHUT1,                 // VL53LXX_XSHUT (the max number of sensors is VL53LXX_MAX_SENSORS)- Used when connecting multiple VL53LXX
  GPIO_MAX7219CLK, GPIO_MAX7219DIN, GPIO_MAX7219CS, // MAX7219 interface
  GPIO_TFMINIPLUS_TX, GPIO_TFMINIPLUS_RX,  // TFmini Plus ToF sensor
  GPIO_ZEROCROSS,
#ifdef ESP32
  GPIO_HALLEFFECT,
  GPIO_EPD_DATA,                       // Base connection EPD driver
#endif
  GPIO_INPUT,
#ifdef ESP32
  GPIO_KEY1_PD, GPIO_KEY1_INV_PD, GPIO_SWT1_PD,
#endif
  GPIO_I2S_DOUT, GPIO_I2S_BCLK, GPIO_I2S_WS,
  GPIO_I2S_DIN,  GPIO_I2S_BCLK_IN,  GPIO_I2S_WS_IN,
  GPIO_INTERRUPT,
  GPIO_MCP2515_CS,                     // MCP2515 Chip Select
  GPIO_HRG15_TX, GPIO_HRG15_RX,        // Hydreon RG-15 rain sensor serial interface
  GPIO_VINDRIKTNING_RX,                // IKEA VINDRIKTNING Serial interface
  GPIO_BL0939_RX,                      // BL0939 Serial interface (Dual R3 v2)
  GPIO_BL0942_RX,                      // BL0942 Serial interface
  GPIO_HM330X_SET,                     // HM330X SET pin (sleep when low)
  GPIO_HEARTBEAT, GPIO_HEARTBEAT_INV,
  GPIO_SHIFT595_SRCLK, GPIO_SHIFT595_RCLK, GPIO_SHIFT595_OE, GPIO_SHIFT595_SER,   // 74x595 Shift register
  GPIO_SOLAXX1_RTS,                    // Solax Inverter Serial interface
  GPIO_OPTION_E,                       // Emulated module
  GPIO_SDM230_TX, GPIO_SDM230_RX,      // SDM230 Serial interface
  GPIO_ADC_MQ,                         // Analog MQ Sensor
  GPIO_CM11_TXD, GPIO_CM11_RXD,        // CM11 Serial interface
  GPIO_BL6523_TX, GPIO_BL6523_RX,      // BL6523 based Watt meter Serial interface
  GPIO_ADE7880_IRQ,                    // ADE7880 IRQ
  GPIO_RESET,                          // Generic reset
  GPIO_MS01,                           // Sonoff MS01 Moisture Sensor 1wire interface
  GPIO_SDIO_CMD, GPIO_SDIO_CLK, GPIO_SDIO_D0, GPIO_SDIO_D1, GPIO_SDIO_D2, GPIO_SDIO_D3, // SD Card SDIO interface, including 1-bit and 4-bit modes
  GPIO_FLOWRATEMETER_IN,               // Flowrate Meter
  GPIO_BP5758D_CLK, GPIO_BP5758D_DAT,  // BP5758D PWM controller
  GPIO_SM2335_CLK, GPIO_SM2335_DAT,    // SM2335 PWM controller
  GPIO_MP3_DFR562_BUSY,                // RB-DFR-562, DFPlayer Mini MP3 Player busy flag
  GPIO_TM1621_CS, GPIO_TM1621_WR, GPIO_TM1621_RD, GPIO_TM1621_DAT,  // Sonoff POWR3xxD and THR3xxD LCD display
  GPIO_REL1_BI, GPIO_REL1_BI_INV,      // 8 x Relays bistable
  GPIO_I2S_MCLK,
  GPIO_MBR_TX, GPIO_MBR_RX,            // Modbus Bridge Serial interface
  GPIO_ADE7953_RST,                    // ADE7953 Reset
  GPIO_NRG_MBS_TX, GPIO_NRG_MBS_RX,    // Generic Energy Modbus device
  GPIO_ADE7953_CS,                     // ADE7953 SPI Chip Select
  GPIO_DALI_RX, GPIO_DALI_TX,          // Dali
  GPIO_BP1658CJ_CLK, GPIO_BP1658CJ_DAT,// BP1658CJ
  GPIO_DINGTIAN_CLK, GPIO_DINGTIAN_SDI, GPIO_DINGTIAN_Q7, GPIO_DINGTIAN_PL, GPIO_DINGTIAN_RCK,  // Dingtian relay board - 595's & 165's pins
  GPIO_LD2410_TX, GPIO_LD2410_RX,      // HLK-LD2410
  GPIO_MBR_TX_ENA, GPIO_NRG_MBS_TX_ENA, // Modbus Bridge Serial Transmit Enable
  GPIO_ME007_TRIG, GPIO_ME007_RX,       // ME007 Serial/Trigger interface
  GPIO_TUYAMCUBR_TX, GPIO_TUYAMCUBR_RX, // TuyaMCU Bridge
  GPIO_BIOPDU_PZEM0XX_TX, GPIO_BIOPDU_PZEM016_RX, GPIO_BIOPDU_BIT, // Biomine BioPDU 625x12
  GPIO_MCP23XXX_INT, GPIO_MCP23SXX_CS,  // MCP23xxx Int and SPI Chip select
  GPIO_PCF8574_INT,                     // PCF8574 interrupt
  GPIO_LOX_O2_RX,                       // LOX-O2 RX
  GPIO_GM861_TX, GPIO_GM861_RX,         // GM861 Serial interface
  GPIO_DINGTIAN_OE,                     // New version of Dingtian relay board where PL is not shared with OE
  GPIO_HDMI_CEC,                        // Support for HDMI CEC
  GPIO_HC8_RXD,                         // HC8 Serial interface
  GPIO_I2S_DAC,                         // Audio DAC support for ESP32 and ESP32S2
  GPIO_MAGIC_SWITCH,                    // MagicSwitch as in Sonoff BasicR4
  GPIO_PIPSOLAR_TX, GPIO_PIPSOLAR_RX,   // pipsolar inverter
  GPIO_LORA_CS, GPIO_LORA_RST, GPIO_LORA_BUSY, GPIO_LORA_DI0, GPIO_LORA_DI1, GPIO_LORA_DI2, GPIO_LORA_DI3, GPIO_LORA_DI4, GPIO_LORA_DI5,  // LoRa SPI
  GPIO_TS_SPI_CS, GPIO_TS_RST, GPIO_TS_IRQ, // SPI for Universal Touch Screen
  GPIO_SENSOR_END };

// Error as warning to rethink GPIO usage with max 2045
static_assert(GPIO_SENSOR_END < 2000, "Too many UserSelectablePins");

enum ProgramSelectablePins {
  GPIO_FIX_START = 2046,
  GPIO_USER,           // User configurable needs to be 2047
  GPIO_MAX };

#define MAX_OPTIONS_A  7                   // Increase if more bits are used from GpioOptionABits

typedef union {                            // Restricted by MISRA-C Rule 18.4 but so useful...
  uint32_t data;                           // Allow bit manipulation using SetOption
  struct {                                 // GPIO Option_A1 .. Option_A32
    uint32_t pwm1_input : 1;               // bit 0 (v9.2.0.1)   - Option_A1 - (Light) Change PWM1 to input on power off and no fade running (1)
    uint32_t dummy_energy : 1;             // bit 1 (v9.3.1.2)   - Option_A2 - (Energy) Enable dummy values
    uint32_t udisplay_driver : 1;          // bit 2 (v9.3.1.2)   - Option_A3 - (Display) Universal display driver
    uint32_t enable_ccloader : 1;          // bit 3 (v9.4.0.5)   - Option_A4 - (Zigbee) Enable CCLoader using Zigbee Rx/Tx/Rst Gpios
    uint32_t rotary_mi_desk : 1;           // bit 4 (v9.5.0.5)   - Option_A5 - (Rotary) Enable Mi Desk emulation
    uint32_t linkind_support : 1;          // bit 5 (v10.1.0.4)  - Option_A6 - (Light) LinkInd support
    uint32_t shelly_pro : 1;               // bit 6 (v12.2.0.1)  - Option_A7 - (Device) Shelly Pro
    uint32_t spare07 : 1;                  // bit 7
    uint32_t spare08 : 1;                  // bit 8
    uint32_t spare09 : 1;                  // bit 9
    uint32_t spare10 : 1;                  // bit 10
    uint32_t spare11 : 1;                  // bit 11
    uint32_t spare12 : 1;                  // bit 12
    uint32_t spare13 : 1;                  // bit 13
    uint32_t spare14 : 1;                  // bit 14
    uint32_t spare15 : 1;                  // bit 15
    uint32_t spare16 : 1;                  // bit 16
    uint32_t spare17 : 1;                  // bit 17
    uint32_t spare18 : 1;                  // bit 18
    uint32_t spare19 : 1;                  // bit 19
    uint32_t spare20 : 1;                  // bit 20
    uint32_t spare21 : 1;                  // bit 21
    uint32_t spare22 : 1;                  // bit 22
    uint32_t spare23 : 1;                  // bit 23
    uint32_t spare24 : 1;                  // bit 24
    uint32_t spare25 : 1;                  // bit 25
    uint32_t spare26 : 1;                  // bit 26
    uint32_t spare27 : 1;                  // bit 27
    uint32_t spare28 : 1;                  // bit 28
    uint32_t spare29 : 1;                  // bit 29
    uint32_t spare30 : 1;                  // bit 30
    uint32_t spare31 : 1;                  // bit 31
  };
} GpioOptionABits;

#ifdef ESP32
enum SupportedEmulationModules {
  SONOFF_BASIC, SONOFF_RF, SONOFF_SV, SONOFF_TH, SONOFF_DUAL, SONOFF_POW, SONOFF_4CH, SONOFF_S2X, SLAMPHER, SONOFF_TOUCH,
  SONOFF_LED, CH1, CH4, MOTOR, ELECTRODRAGON, EXS_RELAY, WION, WEMOS_DUMMY, SONOFF_DEV, H801,
  SONOFF_SC, SONOFF_BN, SONOFF_4CHPRO, HUAFAN_SS, SONOFF_BRIDGE, SONOFF_B1, AILIGHT, SONOFF_T11, SONOFF_T12, SONOFF_T13,
  SUPLA1, WITTY, YUNSHAN, MAGICHOME, LUANIHVIO, KMC_70011, ARILUX_LC01, ARILUX_LC11, SONOFF_DUAL_R2, ARILUX_LC06,
  SONOFF_S31, ZENGGE_ZF_WF017, SONOFF_POW_R2, SONOFF_IFAN02, BLITZWOLF_BWSHP, SHELLY1, SHELLY2, PHILIPS, NEO_COOLCAM, ESP_SWITCH,
  OBI, TECKIN, APLIC_WDP303075, TUYA_DIMMER, GOSUND, ARMTRONIX_DIMMERS, SK03_TUYA, PS_16_DZ, TECKIN_US, MANZOKU_EU_4,
  OBI2, YTF_IR_BRIDGE, DIGOO, KA10, ZX2820, MI_DESK_LAMP, SP10, WAGA, SYF05, SONOFF_L1,
  SONOFF_IFAN03, EXS_DIMMER, PWM_DIMMER, SONOFF_D1, SONOFF_ZB_BRIDGE,
  MAXMODULE_EMULATION };

#define MAX_OPTIONS_E  1                   // Increase if more emulated modules are supported from kModuleEmulationList

const uint8_t kModuleEmulationList[] PROGMEM = {
  PWM_DIMMER                               // (v10.1.0.4)  - Option_E1 - (Light) USE_PWM_DIMMER support
};
#endif  // ESP32

// Text in webpage Module Parameters and commands GPIOS and GPIO
const char kSensorNames[] PROGMEM =
  D_SENSOR_NONE "|"
  D_SENSOR_BUTTON "|" D_SENSOR_BUTTON "_n|" D_SENSOR_BUTTON "_i|" D_SENSOR_BUTTON "_in|"
  D_SENSOR_SWITCH "|" D_SENSOR_SWITCH "_n|"
  D_SENSOR_RELAY "|" D_SENSOR_RELAY "_i|"
  D_SENSOR_LED "|" D_SENSOR_LED "_i|"
  D_SENSOR_COUNTER "|" D_SENSOR_COUNTER "_n|"
  D_SENSOR_PWM "|" D_SENSOR_PWM "_i|"
  D_SENSOR_BUZZER "|" D_SENSOR_BUZZER "_i|"
  D_SENSOR_LED_LINK "|" D_SENSOR_LED_LINK "_i|"
  D_SENSOR_I2C_SCL "|" D_SENSOR_I2C_SDA "|"
  D_SENSOR_SPI_MISO "|" D_SENSOR_SPI_MOSI "|" D_SENSOR_SPI_CLK "|" D_SENSOR_SPI_CS "|" D_SENSOR_SPI_DC "|"
  D_SENSOR_SSPI_MISO "|" D_SENSOR_SSPI_MOSI "|" D_SENSOR_SSPI_SCLK "|" D_SENSOR_SSPI_CS "|" D_SENSOR_SSPI_DC "|"
  D_SENSOR_BACKLIGHT "|" D_SENSOR_DISP_RESET "|"
  D_SENSOR_IRSEND "|" D_SENSOR_IRRECV "|"
  D_SENSOR_RFSEND "|" D_SENSOR_RFRECV "|"
  D_SENSOR_DHT11 "|" D_SENSOR_AM2301 "|" D_SENSOR_SI7021 "|" D_SENSOR_DHT11 "_o|"
  D_SENSOR_DS18X20 "|" D_SENSOR_DS18X20 "_o|"
  D_SENSOR_WS2812 "|"
  D_SENSOR_MHZ_TX "|" D_SENSOR_MHZ_RX "|"
  D_SENSOR_PZEM0XX_TX "|" D_SENSOR_PZEM004_RX "|" D_SENSOR_PZEM016_RX "|" D_SENSOR_PZEM017_RX "|"
  D_SENSOR_SAIR_TX "|" D_SENSOR_SAIR_RX "|"
  D_SENSOR_PMS5003_TX "|" D_SENSOR_PMS5003_RX "|"
  D_SENSOR_SDS0X1_TX "|" D_SENSOR_SDS0X1_RX "|"
  D_SENSOR_SBR_TX "|" D_SENSOR_SBR_RX "|"
  D_SENSOR_SR04_TRIG "|" D_SENSOR_SR04_ECHO "|"
  D_SENSOR_SDM120_TX "|" D_SENSOR_SDM120_RX "|"
  D_SENSOR_SDM630_TX "|" D_SENSOR_SDM630_RX "|"
  D_SENSOR_TM1638_CLK "|" D_SENSOR_TM1638_DIO "|" D_SENSOR_TM1638_STB "|"
  D_SENSOR_DFR562 "|"
  D_SENSOR_HX711_SCK "|" D_SENSOR_HX711_DAT "|"
  D_SENSOR_TX2X_TX "|"
  D_SENSOR_TUYA_TX "|" D_SENSOR_TUYA_RX "|"
  D_SENSOR_MGC3130_XFER "|" D_SENSOR_MGC3130_RESET "|"
  D_SENSOR_RF_SENSOR "|"
  D_SENSOR_AZ_TX "|" D_SENSOR_AZ_RX "|"
  D_SENSOR_MAX31855_CS "|" D_SENSOR_MAX31855_CLK "|" D_SENSOR_MAX31855_DO "|"
  D_SENSOR_NRG_SEL "|" D_SENSOR_NRG_SEL "_i|" D_SENSOR_NRG_CF1 "|" D_SENSOR_HLW_CF "|" D_SENSOR_HJL_CF "|"
  D_SENSOR_MCP39F5_TX "|" D_SENSOR_MCP39F5_RX "|" D_SENSOR_MCP39F5_RST "|"
  D_SENSOR_PN532_TX "|" D_SENSOR_PN532_RX "|"
  D_SENSOR_SM16716_CLK "|" D_SENSOR_SM16716_DAT "|" D_SENSOR_SM16716_POWER "|"
  D_SENSOR_MY92X1_DI "|" D_SENSOR_MY92X1_DCKI "|"
  D_SENSOR_CSE7766_TX "|" D_SENSOR_CSE7766_RX "|"
  D_SENSOR_ARIRFRCV "|" D_SENSOR_ARIRFSEL "|"
  D_SENSOR_TXD "|" D_SENSOR_RXD "|"
  D_SENSOR_ROTARY " A|" D_SENSOR_ROTARY " B|"
  D_SENSOR_ADC_JOYSTICK "|"
  D_SENSOR_MAX31865_CS "|"
  D_SENSOR_HRE_CLOCK "|" D_SENSOR_HRE_DATA "|"
  D_SENSOR_ADE7953_IRQ "|"
  D_SENSOR_SOLAXX1_TX "|" D_SENSOR_SOLAXX1_RX "|"
  D_SENSOR_ZIGBEE_TXD "|" D_SENSOR_ZIGBEE_RXD "|"
  D_SENSOR_RDM6300_RX "|"
  D_SENSOR_IBEACON_TX "|" D_SENSOR_IBEACON_RX "|"
  D_SENSOR_A4988_DIR "|" D_SENSOR_A4988_STP "|" D_SENSOR_A4988_ENA "|" D_SENSOR_A4988_MS1 "|"
  D_SENSOR_OUTPUT_HI "|" D_SENSOR_OUTPUT_LO "|"
  D_SENSOR_DDS2382_TX "|" D_SENSOR_DDS2382_RX "|"
  D_SENSOR_DDSU666_TX "|" D_SENSOR_DDSU666_RX "|"
  D_SENSOR_SM2135_CLK "|" D_SENSOR_SM2135_DAT "|"
  D_SENSOR_DEEPSLEEP "|" D_SENSOR_EXS_ENABLE "|"
  D_SENSOR_CLIENT_TX "|" D_SENSOR_CLIENT_RX "|" D_SENSOR_CLIENT_RESET "|" D_SENSOR_CLIENT_RESET "_i|"
  D_SENSOR_HPMA_RX "|" D_SENSOR_HPMA_TX "|"
  D_SENSOR_GPS_RX "|" D_SENSOR_GPS_TX "|"
  D_SENSOR_HM10_RX "|" D_SENSOR_HM10_TX "|"
  D_SENSOR_LE01MR_RX "|" D_SENSOR_LE01MR_TX "|"
  D_SENSOR_CC1101_GDO0 "|" D_SENSOR_CC1101_GDO2 "|"
  D_SENSOR_HRXL_RX "|"
  D_SENSOR_ELECTRIQ_MOODL "|"
  D_SENSOR_AS3935 "|"
  D_SENSOR_ADC_INPUT "|"
  D_SENSOR_ADC_TEMP "|"
  D_SENSOR_ADC_LIGHT "|"
  D_SENSOR_ADC_BUTTON "|" D_SENSOR_ADC_BUTTON "_i|"
  D_SENSOR_ADC_RANGE "|"
  D_SENSOR_ADC_CT_POWER "|"
#ifdef ESP32
  D_GPIO_WEBCAM_PWDN "|" D_GPIO_WEBCAM_RESET "|" D_GPIO_WEBCAM_XCLK "|"
  D_GPIO_WEBCAM_SIOD "|" D_GPIO_WEBCAM_SIOC "|"
  D_GPIO_WEBCAM_DATA "|"
  D_GPIO_WEBCAM_VSYNC "|" D_GPIO_WEBCAM_HREF "|" D_GPIO_WEBCAM_PCLK "|"
  D_GPIO_WEBCAM_PSCLK "|"
  D_GPIO_WEBCAM_HSD "|"
  D_GPIO_WEBCAM_PSRCS "|"
#endif
  D_SENSOR_BOILER_OT_RX "|" D_SENSOR_BOILER_OT_TX "|"
  D_SENSOR_WINDMETER_SPEED "|" D_SENSOR_BUTTON "_tc|"
  D_SENSOR_BL0940_RX "|"
  D_SENSOR_TCP_TXD "|" D_SENSOR_TCP_RXD "|"
#ifdef ESP32
  D_SENSOR_ETH_PHY_POWER "|" D_SENSOR_ETH_PHY_MDC "|" D_SENSOR_ETH_PHY_MDIO "|"
#endif
  D_SENSOR_TELEINFO_RX "|" D_SENSOR_TELEINFO_ENABLE "|"
  D_SENSOR_LMT01_PULSE "|"
  D_SENSOR_IEM3000_TX "|" D_SENSOR_IEM3000_RX "|"
  D_SENSOR_ZIGBEE_RST "|"
  D_SENSOR_DYP_RX "|"
  D_SENSOR_MIEL_HVAC_TX "|" D_SENSOR_MIEL_HVAC_RX "|"
  D_SENSOR_WE517_TX "|" D_SENSOR_WE517_RX "|"
  D_SENSOR_AS608_TX "|" D_SENSOR_AS608_RX "|"
  D_SENSOR_SHELLY_DIMMER_BOOT0 "|" D_SENSOR_SHELLY_DIMMER_RST_INV "|"
  D_SENSOR_RC522_RST "|"
  D_SENSOR_P9813_CLK "|" D_SENSOR_P9813_DAT "|"
  D_SENSOR_OPTION " A|"
  D_SENSOR_FTC532 "|"
  D_SENSOR_RC522_CS "|"
  D_SENSOR_NRF24_CS "|" D_SENSOR_NRF24_DC "|"
  D_SENSOR_ILI9341_CS "|" D_SENSOR_ILI9341_DC "|"
  D_SENSOR_ILI9488_CS "|"
  D_SENSOR_EPAPER29_CS "|"
  D_SENSOR_EPAPER42_CS "|"
  D_SENSOR_SSD1351_CS "|"
  D_SENSOR_RA8876_CS "|"
  D_SENSOR_ST7789_CS "|" D_SENSOR_ST7789_DC "|"
  D_SENSOR_SSD1331_CS "|" D_SENSOR_SSD1331_DC "|"
  D_SENSOR_SDCARD_CS "|"
  D_SENSOR_ROTARY " A_n|" D_SENSOR_ROTARY " B_n|"
  D_SENSOR_ADC_PH "|"
  D_SENSOR_BS814_CLK "|" D_SENSOR_BS814_DAT "|"
  D_SENSOR_WIEGAND_D0 "|" D_SENSOR_WIEGAND_D1 "|"
  D_SENSOR_NEOPOOL_TX "|" D_SENSOR_NEOPOOL_RX "|"
  D_SENSOR_SDM72_TX "|" D_SENSOR_SDM72_RX "|"
  D_SENSOR_TM1637_CLK "|" D_SENSOR_TM1637_DIO "|"
  D_SENSOR_PROJECTOR_CTRL_TX "|" D_SENSOR_PROJECTOR_CTRL_RX "|"
  D_SENSOR_SSD1351_DC "|"
  D_SENSOR_XPT2046_CS "|"
  D_SENSOR_CSE7761_TX "|" D_SENSOR_CSE7761_RX "|"
  D_SENSOR_VL53LXX_XSHUT "|"
  D_SENSOR_MAX7219_CLK "|" D_SENSOR_MAX7219_DIN "|" D_SENSOR_MAX7219_CS "|"
  D_SENSOR_TFMINIPLUS_TX "|" D_SENSOR_TFMINIPLUS_RX "|"
  D_SENSOR_ZEROCROSS "|"
#ifdef ESP32
  D_SENSOR_HALLEFFECT "|"
  D_SENSOR_EPD_DATA "|"
#endif
  D_SENSOR_INPUT "|"
#ifdef ESP32
  D_SENSOR_BUTTON "_d|" D_SENSOR_BUTTON "_id|" D_SENSOR_SWITCH "_d|"
#endif
  D_SENSOR_I2S_DOUT "|" D_SENSOR_I2S_BCLK "|" D_SENSOR_I2S_WS "|"
  D_SENSOR_I2S_DIN "|" D_SENSOR_I2S_BCLK_IN "|" D_SENSOR_I2S_WS_IN "|"
  D_SENSOR_INTERRUPT "|"
  D_SENSOR_MCP2515_CS "|"
  D_SENSOR_HRG15_TX "|" D_SENSOR_HRG15_RX "|"
  D_SENSOR_VINDRIKTNING_RX "|"
  D_SENSOR_BL0939_RX "|"
  D_SENSOR_BL0942_RX "|"
  D_SENSOR_HM330X_SET "|"
  D_SENSOR_HEARTBEAT "|" D_SENSOR_HEARTBEAT "_i|"
  D_GPIO_SHIFT595_SRCLK "|" D_GPIO_SHIFT595_RCLK "|" D_GPIO_SHIFT595_OE "|" D_GPIO_SHIFT595_SER "|"
  D_SENSOR_SOLAXX1_RTS "|"
  D_SENSOR_OPTION " E|"
  D_SENSOR_SDM230_TX "|" D_SENSOR_SDM230_RX "|"
  D_SENSOR_ADC_MQ "|"
  D_SENSOR_CM11_TX "|" D_SENSOR_CM11_RX "|"
  D_SENSOR_BL6523_TX "|" D_SENSOR_BL6523_RX "|"
  D_SENSOR_ADE7880_IRQ "|"
  D_SENSOR_RESET "|"
  D_SENSOR_MS01 "|"
  D_SENSOR_SDIO_CMD "|"
  D_SENSOR_SDIO_CLK "|"
  D_SENSOR_SDIO_D0 "|"
  D_SENSOR_SDIO_D1 "|"
  D_SENSOR_SDIO_D2 "|"
  D_SENSOR_SDIO_D3 "|"
  D_SENSOR_FLOWRATEMETER "|"
  D_SENSOR_BP5758D_CLK "|" D_SENSOR_BP5758D_DAT "|"
  D_SENSOR_SM2335_CLK "|" D_SENSOR_SM2335_DAT "|"
  D_SENSOR_DFR562_BUSY "|"
  D_GPIO_TM1621_CS "|" D_GPIO_TM1621_WR "|" D_GPIO_TM1621_RD "|" D_GPIO_TM1621_DAT "|"
  D_SENSOR_RELAY "_b|" D_SENSOR_RELAY "_bi|"
  D_SENSOR_I2S_MCLK "|"
  D_SENSOR_MBR_TX "|" D_SENSOR_MBR_RX "|"
  D_SENSOR_ADE7953_RST "|"
  D_SENSOR_NRG_MBS_TX "|" D_SENSOR_NRG_MBS_RX "|"
  D_SENSOR_ADE7953_CS "|"
  D_SENSOR_DALI_RX "|" D_SENSOR_DALI_TX "|"
  D_SENSOR_BP1658CJ_CLK "|" D_SENSOR_BP1658CJ_DAT "|"
  D_GPIO_DINGTIAN_CLK "|" D_GPIO_DINGTIAN_SDI "|" D_GPIO_DINGTIAN_Q7 "|" D_GPIO_DINGTIAN_PL "|" D_GPIO_DINGTIAN_RCK "|"
  D_SENSOR_LD2410_TX "|" D_SENSOR_LD2410_RX "|"
  D_SENSOR_MBR_TX_ENA "|" D_SENSOR_NRG_MBS_TX_ENA "|"
  D_SENSOR_ME007_TRIG "|" D_SENSOR_ME007_RX "|"
  D_SENSOR_TUYAMCUBR_TX "|" D_SENSOR_TUYAMCUBR_RX "|"
  D_SENSOR_BIOPDU_PZEM0XX_TX "|" D_SENSOR_BIOPDU_PZEM016_RX "|" D_SENSOR_BIOPDU_BIT "|"
  D_SENSOR_MCP23XXX_INT "|" D_SENSOR_MCP23SXX_CS "|"
  D_SENSOR_PCF8574_INT "|"
  D_SENSOR_LOX_O2_RX "|"
  D_SENSOR_GM861_TX "|" D_SENSOR_GM861_RX "|"
  D_GPIO_DINGTIAN_OE "|"
  D_SENSOR_HDMI_CEC "|"
  D_SENSOR_HC8_RX "|"
  D_SENSOR_I2S_DAC "|"
  D_GPIO_MAGIC_SWITCH "|"
  D_SENSOR_PIPSOLAR_TX "|" D_SENSOR_PIPSOLAR_RX "|"
  D_GPIO_LORA_CS "|" D_GPIO_LORA_RST "|" D_GPIO_LORA_BUSY "|" D_GPIO_LORA_DI "0|" D_GPIO_LORA_DI "1|" D_GPIO_LORA_DI "2|" D_GPIO_LORA_DI "3|" D_GPIO_LORA_DI "4|" D_GPIO_LORA_DI "5|"
  D_GPIO_TS_SPI_CS "|" D_GPIO_TS_RST "|" D_GPIO_TS_IRQ "|"
  ;

const char kSensorNamesFixed[] PROGMEM =
  D_SENSOR_USER;

// Max number of GPIOs
#define MAX_MAX31855S    6
#define MAX_MAX31865S    6
#define MAX_MCP23XXX     6
#define MAX_FLOWRATEMETER 2
#define MAX_A4988_MSS    3
#define MAX_WEBCAM_DATA  8
#define MAX_WEBCAM_HSD   3
#define MAX_SM2135_DAT   10
#define MAX_SM2335_DAT   16
#define MAX_DSB          4
#define MAX_BP1658CJ_DAT 16
#define MAX_DINGTIAN_SHIFT  4
#define MAX_MAGIC_SWITCH_MODES   2
#define MAX_BL0942_RX    8              // Baudrates 1/5 (4800), 2/6 (9600), 3/7 (19200), 4/8 (38400), Support Positive values only 1..4, Support also negative values 5..8

const uint16_t kGpioNiceList[] PROGMEM = {
  GPIO_NONE,                            // Not used
  AGPIO(GPIO_OPTION_A) + MAX_OPTIONS_A, // Device specific options
#ifdef ESP32
  AGPIO(GPIO_OPTION_E) + MAX_OPTIONS_E, // Device module emulation
#endif
  AGPIO(GPIO_KEY1) + MAX_KEYS,          // Buttons
  AGPIO(GPIO_KEY1_NP) + MAX_KEYS,
#ifdef ESP32
  AGPIO(GPIO_KEY1_PD) + MAX_KEYS,
#endif
  AGPIO(GPIO_KEY1_INV) + MAX_KEYS,
  AGPIO(GPIO_KEY1_INV_NP) + MAX_KEYS,
#ifdef ESP32
  AGPIO(GPIO_KEY1_INV_PD) + MAX_KEYS,
#if defined(SOC_TOUCH_VERSION_1) || defined(SOC_TOUCH_VERSION_2)
  AGPIO(GPIO_KEY1_TC) + MAX_KEYS,       // Touch button
#endif  // ESP32 SOC_TOUCH_VERSION_1 or SOC_TOUCH_VERSION_2
#endif
  AGPIO(GPIO_SWT1) + MAX_SWITCHES,      // User connected external switches
  AGPIO(GPIO_SWT1_NP) + MAX_SWITCHES,
#ifdef ESP32
  AGPIO(GPIO_SWT1_PD) + MAX_SWITCHES,
#endif
#ifdef ROTARY_V1
  AGPIO(GPIO_ROT1A) + MAX_ROTARIES,     // Rotary A Pin
  AGPIO(GPIO_ROT1B) + MAX_ROTARIES,     // Rotary B Pin
  AGPIO(GPIO_ROT1A_NP) + MAX_ROTARIES,  // Rotary A Pin No Pullup
  AGPIO(GPIO_ROT1B_NP) + MAX_ROTARIES,  // Rotary B Pin No Pullup
#endif
  AGPIO(GPIO_REL1) + MAX_RELAYS,        // Relays
  AGPIO(GPIO_REL1_INV) + MAX_RELAYS,
  AGPIO(GPIO_REL1_BI) + MAX_RELAYS,     // Bistable (Latching) two coil relays
  AGPIO(GPIO_REL1_BI_INV) + MAX_RELAYS,
  AGPIO(GPIO_LED1) + MAX_LEDS,          // Leds
  AGPIO(GPIO_LED1_INV) + MAX_LEDS,
#ifdef USE_COUNTER
  AGPIO(GPIO_CNTR1) + MAX_COUNTERS,     // Counters
  AGPIO(GPIO_CNTR1_NP) + MAX_COUNTERS,
#endif
  AGPIO(GPIO_PWM1) + MAX_PWMS,          // RGB   Red   or C  Cold White
  AGPIO(GPIO_PWM1_INV) + MAX_PWMS,      // or extended PWM for ESP32
#ifdef USE_BUZZER
  AGPIO(GPIO_BUZZER),                   // Buzzer
  AGPIO(GPIO_BUZZER_INV),               // Inverted buzzer
#endif
  AGPIO(GPIO_LEDLNK),                   // Link led
  AGPIO(GPIO_LEDLNK_INV),               // Inverted link led
#ifdef USE_BERRY
  AGPIO(GPIO_INPUT) + MAX_SWITCHES,     // Pure digital input to be read via Berry
  AGPIO(GPIO_INTERRUPT) + MAX_SWITCHES, // Interrupt pins to be catched by Berry
#endif
  AGPIO(GPIO_OUTPUT_HI),                // Fixed output high
  AGPIO(GPIO_OUTPUT_LO),                // Fixed output low
  AGPIO(GPIO_HEARTBEAT),                // Every second pulsed high
  AGPIO(GPIO_HEARTBEAT_INV),            // Every second pulsed low
  AGPIO(GPIO_RESET),                    // Generic reset
#ifdef USE_FTC532
  AGPIO(GPIO_FTC532),                   // FTC532 touch input
#endif
#ifdef USE_BS814A2
  AGPIO(GPIO_BS814_CLK),                // Holtek BS814A2 touch ctrlr
  AGPIO(GPIO_BS814_DAT),
#endif

/*-------------------------------------------------------------------------------------------*\
 * Protocol specifics
\*-------------------------------------------------------------------------------------------*/

#if defined(USE_DALI) && defined(ESP32)
  AGPIO(GPIO_DALI_RX),                  // DALI RX
  AGPIO(GPIO_DALI_TX),                  // DALI TX
#endif  // USE_DALI

#ifdef USE_I2C
  AGPIO(GPIO_I2C_SCL) + MAX_I2C,        // I2C SCL
  AGPIO(GPIO_I2C_SDA) + MAX_I2C,        // I2C SDA
#ifdef USE_PCF8574
  AGPIO(GPIO_PCF8574_INT),              // PCF8574 Interrupt
#endif  // USE_PCF8574
#endif

#if defined(USE_I2S_AUDIO) || defined (USE_I2S)
  AGPIO(GPIO_I2S_MCLK) + MAX_I2S,       // I2S master clock
  AGPIO(GPIO_I2S_BCLK) + MAX_I2S,       // I2S bit clock
  AGPIO(GPIO_I2S_DOUT) + MAX_I2S,       // I2S Out Data
  AGPIO(GPIO_I2S_DAC) + 2,              // I2S DAC Output
  AGPIO(GPIO_I2S_WS) + MAX_I2S,         // I2S word select
  AGPIO(GPIO_I2S_DIN) + MAX_I2S,        // I2S IN Data
#endif
#ifdef USE_I2S
  AGPIO(GPIO_I2S_BCLK_IN) + MAX_I2S,    // I2S bit clock in
  AGPIO(GPIO_I2S_WS_IN) + MAX_I2S,      // I2S word select in
#endif

#ifdef USE_SPI
  AGPIO(GPIO_SPI_MISO) + MAX_SPI,       // SPI MISO
  AGPIO(GPIO_SPI_MOSI) + MAX_SPI,       // SPI MOSI
  AGPIO(GPIO_SPI_CLK) + MAX_SPI,        // SPI Clk
  AGPIO(GPIO_SPI_CS) + MAX_SPI,         // SPI Chip Select
  AGPIO(GPIO_SPI_DC) + MAX_SPI,         // SPI Data Direction
#ifdef USE_NRF24
  AGPIO(GPIO_NRF24_CS),
  AGPIO(GPIO_NRF24_DC),
#endif
#ifdef USE_RC522
  AGPIO(GPIO_RC522_CS),                 // RC522 Rfid Chip Select
  AGPIO(GPIO_RC522_RST),                // RC522 Rfid Reset
#endif
#ifdef USE_SDCARD
  AGPIO(GPIO_SDCARD_CS),                // SDCard in SPI mode
#endif  // USE_SDCARD
#if defined(USE_MCP2515) || defined(USE_CANSNIFFER)
  AGPIO(GPIO_MCP2515_CS),
#endif  // USE_MCP2515
#ifdef USE_MCP23XXX_DRV
  AGPIO(GPIO_MCP23SXX_CS) + MAX_MCP23XXX,
#endif  // USE_MCP23XXX_DRV
#ifdef USE_SPI_LORA
  AGPIO(GPIO_LORA_CS),
  AGPIO(GPIO_LORA_RST),
  AGPIO(GPIO_LORA_BUSY),
  AGPIO(GPIO_LORA_DI0),
  AGPIO(GPIO_LORA_DI1),
  AGPIO(GPIO_LORA_DI2),
  AGPIO(GPIO_LORA_DI3),
  AGPIO(GPIO_LORA_DI4),
  AGPIO(GPIO_LORA_DI5),
#endif  // USE_SPI_LORA
#endif  // USE_SPI

#if defined(USE_SDCARD) && defined(ESP32)
  AGPIO(GPIO_SDIO_CMD),                 // SDCard in SDIO mode
  AGPIO(GPIO_SDIO_CLK),
  AGPIO(GPIO_SDIO_D0),
  AGPIO(GPIO_SDIO_D1),                  // (opt) if in 4-bit mode, DAT1-3 are needed
  AGPIO(GPIO_SDIO_D2),
  AGPIO(GPIO_SDIO_D3),
#endif  // USE_SDCARD

  AGPIO(GPIO_SSPI_MISO),                // Software SPI Master Input Client Output
  AGPIO(GPIO_SSPI_MOSI),                // Software SPI Master Output Client Input
  AGPIO(GPIO_SSPI_SCLK),                // Software SPI Serial Clock
  AGPIO(GPIO_SSPI_CS),                  // Software SPI Chip Select
  AGPIO(GPIO_SSPI_DC),                  // Software SPI Data or Command

#if defined(USE_DISPLAY) || defined(USE_LVGL)
#ifdef USE_UNIVERSAL_TOUCH
  AGPIO(GPIO_TS_SPI_CS),                 // Touch CS
  AGPIO(GPIO_TS_RST),                // Touch Reset
  AGPIO(GPIO_TS_IRQ),                // Touch IRQ
#endif // USE_UNIVERSAL_TOUCH
#ifdef USE_DISPLAY_ILI9341
  AGPIO(GPIO_ILI9341_CS),
  AGPIO(GPIO_ILI9341_DC),
#endif  // USE_DISPLAY_ILI9341

#ifdef USE_XPT2046
  AGPIO(GPIO_XPT2046_CS),               // XPT2046 SPI Chip Select
#endif

#ifdef USE_DISPLAY_ILI9488
  AGPIO(GPIO_ILI9488_CS),
#endif  // USE_DISPLAY_ILI9488
#ifdef USE_DISPLAY_EPAPER_29
  AGPIO(GPIO_EPAPER29_CS),
#endif  // USE_DISPLAY_EPAPER_29
#ifdef USE_DISPLAY_EPAPER_42
  AGPIO(GPIO_EPAPER42_CS),
#endif  // USE_DISPLAY_EPAPER_42
#ifdef USE_DISPLAY_SSD1351
  AGPIO(GPIO_SSD1351_CS),
  AGPIO(GPIO_SSD1351_DC),
#endif  // USE_DISPLAY_SSD1351
#ifdef USE_DISPLAY_RA8876
  AGPIO(GPIO_RA8876_CS),
#endif  // USE_DISPLAY_RA8876
#ifdef USE_DISPLAY_ST7789
  AGPIO(GPIO_ST7789_CS),
  AGPIO(GPIO_ST7789_DC),
#endif  // USE_DISPLAY_ST7789
#ifdef USE_DISPLAY_SSD1331
  AGPIO(GPIO_SSD1331_CS),
  AGPIO(GPIO_SSD1331_DC),
#endif  // USE_DISPLAY_SSD1331
#ifdef USE_DISPLAY_MAX7219_MATRIX
  #undef USE_DISPLAY_MAX7219
  #undef USE_DISPLAY_TM1637
  AGPIO(GPIO_MAX7219CLK),
  AGPIO(GPIO_MAX7219DIN),
  AGPIO(GPIO_MAX7219CS),
#endif  // USE_DISPLAY_MAX7219_MATRIX
#ifdef USE_DISPLAY_MAX7219
  AGPIO(GPIO_MAX7219CLK),
  AGPIO(GPIO_MAX7219DIN),
  AGPIO(GPIO_MAX7219CS),
#endif  // USE_DISPLAY_MAX7219
#ifdef USE_DISPLAY_TM1637
  AGPIO(GPIO_TM1637CLK),
  AGPIO(GPIO_TM1637DIO),
  AGPIO(GPIO_TM1638CLK),
  AGPIO(GPIO_TM1638DIO),
  AGPIO(GPIO_TM1638STB),
#endif  // USE_DISPLAY_TM1637
  AGPIO(GPIO_BACKLIGHT),                // Display backlight control
  AGPIO(GPIO_OLED_RESET),               // OLED Display Reset
#ifdef ESP32
  AGPIO(GPIO_EPD_DATA),                 // Base connection EPD driver
#endif
#endif  // USE_DISPLAY

#ifdef USE_DISPLAY_TM1621_SONOFF
// Initial support outside display driver
  AGPIO(GPIO_TM1621_CS),
  AGPIO(GPIO_TM1621_WR),
  AGPIO(GPIO_TM1621_RD),
  AGPIO(GPIO_TM1621_DAT),
#endif  // USE_DISPLAY_TM1621_SONOFF

#ifdef USE_MAX31865
  AGPIO(GPIO_SSPI_MAX31865_CS1) + MAX_MAX31865S,
#endif

#ifdef USE_MCP23XXX_DRV
  AGPIO(GPIO_MCP23XXX_INT) + MAX_MCP23XXX,
#endif

#ifdef USE_HDMI_CEC
  AGPIO(GPIO_HDMI_CEC),                 // HDMI CEC bus
#endif

  AGPIO(GPIO_TXD),                      // Serial interface
  AGPIO(GPIO_RXD),                      // Serial interface

/*-------------------------------------------------------------------------------------------*\
 * Single wire sensors
\*-------------------------------------------------------------------------------------------*/

#ifdef USE_DHT
  AGPIO(GPIO_DHT11),                    // DHT11
  AGPIO(GPIO_DHT22),                    // DHT21, DHT22, AM2301, AM2302, AM2321
  AGPIO(GPIO_SI7021),                   // iTead SI7021
  AGPIO(GPIO_MS01),                     // Sonoff MS01
  AGPIO(GPIO_DHT11_OUT),                // Pseudo Single wire DHT11, DHT21, DHT22, AM2301, AM2302, AM2321
#endif
#ifdef USE_DS18x20
  AGPIO(GPIO_DSB) + MAX_DSB,            // Single wire DS18B20 or DS18S20
  AGPIO(GPIO_DSB_OUT) + MAX_DSB,        // Pseudo Single wire DS18B20 or DS18S20
#endif  // USE_DS18x20
#ifdef USE_LMT01
  AGPIO(GPIO_LMT01),                    // LMT01, count pulses on GPIO
#endif

/*-------------------------------------------------------------------------------------------*\
 * Light
\*-------------------------------------------------------------------------------------------*/

#ifdef USE_LIGHT
#ifdef USE_WS2812
#if (USE_WS2812_HARDWARE == NEO_HW_P9813)
  AGPIO(GPIO_P9813_CLK),                // P9813 CLOCK
  AGPIO(GPIO_P9813_DAT),                // P9813 DATA
#else
  AGPIO(GPIO_WS2812) + (MAX_RMT ? MAX_RMT + 1 : 0), // WS2812 Led string, using RMT on ESP32
#endif  // NEO_HW_P9813
#endif
#ifdef USE_ARILUX_RF
  AGPIO(GPIO_ARIRFRCV),                 // AriLux RF Receive input
  AGPIO(GPIO_ARIRFSEL),                 // Arilux RF Receive input selected
#endif
#ifdef USE_MY92X1
  AGPIO(GPIO_DI),                       // my92x1 PWM input
  AGPIO(GPIO_DCKI),                     // my92x1 CLK input
#endif  // USE_MY92X1
#ifdef USE_SM16716
  AGPIO(GPIO_SM16716_CLK),              // SM16716 CLOCK
  AGPIO(GPIO_SM16716_DAT),              // SM16716 DATA
  AGPIO(GPIO_SM16716_SEL),              // SM16716 SELECT
#endif  // USE_SM16716
#ifdef USE_SM2135
  AGPIO(GPIO_SM2135_CLK),                   // SM2135 CLOCK
  AGPIO(GPIO_SM2135_DAT) + MAX_SM2135_DAT,  // SM2135 DATA
#endif  // USE_SM2135
#ifdef USE_SM2335
  AGPIO(GPIO_SM2335_CLK),                   // SM2335 CLOCK
  AGPIO(GPIO_SM2335_DAT) + MAX_SM2335_DAT,  // SM2335 DATA
#endif  // USE_SM2335
#ifdef USE_BP1658CJ
  AGPIO(GPIO_BP1658CJ_CLK),                    // BP1658CJ CLOCK
  AGPIO(GPIO_BP1658CJ_DAT) + MAX_BP1658CJ_DAT, // BP1658CJ DATA
#endif  // USE_BP1658CJ
#ifdef USE_BP5758D
  AGPIO(GPIO_BP5758D_CLK),              // BP5758D CLOCK
  AGPIO(GPIO_BP5758D_DAT),              // BP5758D DATA
#endif  // USE_BP5758D
#ifdef USE_TUYA_MCU
  AGPIO(GPIO_TUYA_TX),                  // Tuya Serial interface
  AGPIO(GPIO_TUYA_RX),                  // Tuya Serial interface
#endif
#ifdef USE_EXS_DIMMER
  AGPIO(GPIO_EXS_ENABLE),               // EXS MCU Enable
#endif
#ifdef USE_ELECTRIQ_MOODL
  AGPIO(GPIO_ELECTRIQ_MOODL_TX),
#endif
#ifdef USE_SHELLY_DIMMER
  AGPIO(GPIO_SHELLY_DIMMER_BOOT0),
  AGPIO(GPIO_SHELLY_DIMMER_RST_INV),
#endif
#endif  // USE_LIGHT

/*-------------------------------------------------------------------------------------------*\
 * Transmission sensors
\*-------------------------------------------------------------------------------------------*/

#if defined(USE_IR_REMOTE) || defined(USE_IR_REMOTE_FULL)
  AGPIO(GPIO_IRSEND) + MAX_IRSEND,      // IR remote
#if defined(USE_IR_RECEIVE) || defined(USE_IR_REMOTE_FULL)
  AGPIO(GPIO_IRRECV),                   // IR receiver
#endif
#endif
#ifdef USE_RC_SWITCH
  AGPIO(GPIO_RFSEND),                   // RF transmitter
  AGPIO(GPIO_RFRECV),                   // RF receiver
#endif
#ifdef USE_RF_SENSOR
  AGPIO(GPIO_RF_SENSOR),                // Rf receiver with sensor decoding
#endif
#ifdef USE_SR04
  AGPIO(GPIO_SR04_TRIG),                // SR04 Tri/TXgger pin
  AGPIO(GPIO_SR04_ECHO),                // SR04 Ech/RXo pin
#endif
#ifdef USE_ME007
  AGPIO(GPIO_ME007_TRIG),              // ME007 Trigger pin (xsns_23_me007.ino)
  AGPIO(GPIO_ME007_RX),                // ME007 Rx pin (xsns_23_me007.ino)
#endif
#ifdef USE_TM1638
  AGPIO(GPIO_TM1638CLK),                // TM1638 Clock
  AGPIO(GPIO_TM1638DIO),                // TM1638 Data I/O
  AGPIO(GPIO_TM1638STB),                // TM1638 Strobe
#endif
#ifdef USE_HX711
  AGPIO(GPIO_HX711_SCK),                // HX711 Load Cell clock
  AGPIO(GPIO_HX711_DAT),                // HX711 Load Cell data
#endif
#ifdef USE_TFMINIPLUS
  AGPIO(GPIO_TFMINIPLUS_TX),            // TFmini Plus TX pin
  AGPIO(GPIO_TFMINIPLUS_RX),            // TFmini Plus RX pin
#endif

/*-------------------------------------------------------------------------------------------*\
 * Energy sensors
\*-------------------------------------------------------------------------------------------*/

#ifdef USE_ENERGY_SENSOR
#ifdef USE_HLW8012
  AGPIO(GPIO_NRG_SEL),                  // HLW8012/HLJ-01 Sel output (1 = Voltage)
  AGPIO(GPIO_NRG_SEL_INV),              // HLW8012/HLJ-01 Sel output (0 = Voltage)
  AGPIO(GPIO_NRG_CF1),                  // HLW8012/HLJ-01 CF1 voltage / current
  AGPIO(GPIO_HLW_CF),                   // HLW8012 CF power
  AGPIO(GPIO_HJL_CF),                   // HJL-01/BL0937 CF power
#endif
#if defined(USE_I2C) && defined(USE_ADE7880)
  AGPIO(GPIO_ADE7880_IRQ) + 2,          // ADE7880 IRQ - (1 = IRQ1, 2 = IRQ2)
#endif
#ifdef USE_ADE7953
#if defined(USE_I2C) || defined(USE_SPI)
  AGPIO(GPIO_ADE7953_IRQ) + 6,          // ADE7953 IRQ - (1 = Shelly 2.5, 2 = Shelly EM, 3 = Shelly Plus 2PM, 4 = Shelly Pro 1PM, 5 = Shelly Pro 2PM, 6 = Shelly Pro 4PM)
  AGPIO(GPIO_ADE7953_RST),              // ADE7953 Reset
#ifdef USE_SPI
  AGPIO(GPIO_ADE7953_CS) + 2,           // ADE7953 SPI Chip Select (1 = CS1 (1PM, 2PM), 2 = CS2 (2PM))
#endif  // USE_SPI
#endif  // USE_I2C or USE_SPI
#endif  // USE_ADE7953
#ifdef USE_CSE7761
  AGPIO(GPIO_CSE7761_TX),               // CSE7761 Serial interface (Dual R3)
  AGPIO(GPIO_CSE7761_RX),               // CSE7761 Serial interface (Dual R3)
#endif
#ifdef USE_CSE7766
  AGPIO(GPIO_CSE7766_TX),               // CSE7766 Serial interface (S31 and Pow R2)
  AGPIO(GPIO_CSE7766_RX),               // CSE7766 Serial interface (S31 and Pow R2)
#endif
#ifdef USE_MCP39F501
  AGPIO(GPIO_MCP39F5_TX),               // MCP39F501 Serial interface (Shelly2)
  AGPIO(GPIO_MCP39F5_RX),               // MCP39F501 Serial interface (Shelly2)
  AGPIO(GPIO_MCP39F5_RST),              // MCP39F501 Reset (Shelly2)
#endif
  AGPIO(GPIO_NRG_MBS_TX_ENA),           // Generic Energy Modbus Transmit Enable
#if defined(USE_PZEM004T) || defined(USE_PZEM_AC) || defined(USE_PZEM_DC)
  AGPIO(GPIO_PZEM0XX_TX),               // PZEM0XX Serial interface
#endif
#ifdef USE_PZEM004T
  AGPIO(GPIO_PZEM004_RX),               // PZEM004T Serial interface
#endif
#ifdef USE_PZEM_AC
  AGPIO(GPIO_PZEM016_RX),               // PZEM-014,016 Serial Modbus interface
#endif
#ifdef USE_PZEM_DC
  AGPIO(GPIO_PZEM017_RX),               // PZEM-003,017 Serial Modbus interface
#endif
#ifdef USE_MODBUS_ENERGY
  AGPIO(GPIO_NRG_MBS_TX),               // Generic Energy Modbus device
  AGPIO(GPIO_NRG_MBS_RX),
#endif
#ifdef USE_SDM120
  AGPIO(GPIO_SDM120_TX),                // SDM120 Serial interface
  AGPIO(GPIO_SDM120_RX),                // SDM120 Serial interface
#endif
#ifdef USE_SDM630
  AGPIO(GPIO_SDM630_TX),                // SDM630 Serial interface
  AGPIO(GPIO_SDM630_RX),                // SDM630 Serial interface
#endif
#ifdef USE_DDS2382
  AGPIO(GPIO_DDS2382_TX),               // DDS2382 Serial interface
  AGPIO(GPIO_DDS2382_RX),               // DDS2382 Serial interface
#endif
#ifdef USE_DDSU666
  AGPIO(GPIO_DDSU666_TX),               // DDSU666 Serial interface
  AGPIO(GPIO_DDSU666_RX),               // DDSU666 Serial interface
#endif  // USE_DDSU666
#ifdef USE_SOLAX_X1
  AGPIO(GPIO_SOLAXX1_TX),               // Solax Inverter tx pin
  AGPIO(GPIO_SOLAXX1_RX),               // Solax Inverter rx pin
  AGPIO(GPIO_SOLAXX1_RTS),              // Solax Inverter RTS pin
#endif // USE_SOLAX_X1
#ifdef USE_LE01MR
  AGPIO(GPIO_LE01MR_TX),                // F7F LE-01MR energy meter tx pin
  AGPIO(GPIO_LE01MR_RX),                // F7F LE-01MR energy meter rx pin
#endif // IFDEF:USE_LE01MR
#if defined(USE_BL0940) || defined(USE_BL09XX)
  AGPIO(GPIO_BL0939_RX),                // BL0939 Serial interface (Dual R3 v2)
  AGPIO(GPIO_BL0940_RX),                // BL0940 Serial interface
  AGPIO(GPIO_BL0942_RX) + MAX_BL0942_RX,  // BL0942 Serial interface
#endif
#ifdef USE_IEM3000
  AGPIO(GPIO_IEM3000_TX),               // IEM3000 Serial interface
  AGPIO(GPIO_IEM3000_RX),               // IEM3000 Serial interface
#endif
#ifdef USE_WE517
  AGPIO(GPIO_WE517_TX),                 // WE517 Serial interface
  AGPIO(GPIO_WE517_RX),                 // WE517 Serial interface
#endif
#ifdef USE_SDM72
  AGPIO(GPIO_SDM72_TX),                 // SDM72 Serial interface
  AGPIO(GPIO_SDM72_RX),                 // SDM72 Serial interface
#endif
  AGPIO(GPIO_ZEROCROSS),
#ifdef USE_SDM230
  AGPIO(GPIO_SDM230_TX),                // SDM230 Serial interface
  AGPIO(GPIO_SDM230_RX),                // SDM230 Serial interface
#endif
#ifdef USE_BL6523
  AGPIO(GPIO_BL6523_TX),                // BL6523 based Watt meter Serial interface
  AGPIO(GPIO_BL6523_RX),                // BL6523 based Watt meter Serial interface
#endif
#endif  // USE_ENERGY_SENSOR

/*-------------------------------------------------------------------------------------------*\
 * Serial sensors
\*-------------------------------------------------------------------------------------------*/

#ifdef USE_SERIAL_BRIDGE
  AGPIO(GPIO_SBR_TX),                   // Serial Bridge Serial interface
  AGPIO(GPIO_SBR_RX),                   // Serial Bridge Serial interface
#endif
#ifdef USE_MODBUS_BRIDGE
  AGPIO(GPIO_MBR_TX_ENA),               // Modbus Bridge Serial interface
  AGPIO(GPIO_MBR_TX),                   // Modbus Bridge Serial interface
  AGPIO(GPIO_MBR_RX),                   // Modbus Bridge Serial interface
#endif
#ifdef USE_TCP_BRIDGE
  AGPIO(GPIO_TCP_TX),                   // TCP Serial bridge
  AGPIO(GPIO_TCP_RX),                   // TCP Serial bridge
#endif
#ifdef USE_ZIGBEE
  AGPIO(GPIO_ZIGBEE_TX),                // Zigbee Serial interface
  AGPIO(GPIO_ZIGBEE_RX),                // Zigbee Serial interface
  AGPIO(GPIO_ZIGBEE_RST) + 2,           // Zigbee reset, pin 1 is reset, pin 2 is bootloader mode
#endif
#ifdef USE_MHZ19
  AGPIO(GPIO_MHZ_TXD),                  // MH-Z19 Serial interface
  AGPIO(GPIO_MHZ_RXD),                  // MH-Z19 Serial interface
#endif
#ifdef USE_HC8
  AGPIO(GPIO_HC8_RXD),                  // HC8 Serial interface
#endif
#ifdef USE_SENSEAIR
  AGPIO(GPIO_SAIR_TX),                  // SenseAir Serial interface
  AGPIO(GPIO_SAIR_RX),                  // SenseAir Serial interface
#endif
#ifdef USE_NOVA_SDS
  AGPIO(GPIO_SDS0X1_TX),                // Nova Fitness SDS011 Serial interface
  AGPIO(GPIO_SDS0X1_RX),                // Nova Fitness SDS011 Serial interface
#endif
#ifdef USE_HPMA
  AGPIO(GPIO_HPMA_TX),                  // Honeywell HPMA115S0 Serial interface
  AGPIO(GPIO_HPMA_RX),                  // Honeywell HPMA115S0 Serial interface
#endif
#ifdef USE_PMS5003
  AGPIO(GPIO_PMS5003_TX),               // Plantower PMS5003 Serial interface
  AGPIO(GPIO_PMS5003_RX),               // Plantower PMS5003 Serial interface
#endif
#ifdef USE_VINDRIKTNING
  AGPIO(GPIO_VINDRIKTNING_RX),          // Ikea Vindriktning
#endif
#ifdef USE_HM330X
  AGPIO(GPIO_HM330X_SET),               // HM330X Sleep pin (active low)
#endif
#if defined(USE_TX20_WIND_SENSOR) || defined(USE_TX23_WIND_SENSOR) || defined(USE_WS2300_WIND_SENSOR)
  AGPIO(GPIO_TX2X_TXD_BLACK),           // TX20/TX23 Transmission Pin
#endif
#ifdef USE_WINDMETER                    // xsns_68_windmeter.ino
  AGPIO(GPIO_WINDMETER_SPEED),
#endif
#ifdef USE_MP3_PLAYER                   // xdrv_14_mp3.ino
  AGPIO(GPIO_MP3_DFR562),               // RB-DFR-562, DFPlayer Mini MP3 Player Serial interface
  AGPIO(GPIO_MP3_DFR562_BUSY),          // RB-DFR-562, DFPlayer Mini MP3 Player optional Busy flag
  #endif
#ifdef USE_AZ7798                       // xsns_38_az7798
  AGPIO(GPIO_AZ_TXD),                   // AZ-Instrument 7798 CO2 datalogger Serial interface
  AGPIO(GPIO_AZ_RXD),                   // AZ-Instrument 7798 CO2 datalogger Serial interface
#endif
#ifdef USE_PN532_HSU                    // xsns_40_pn532.ino
  AGPIO(GPIO_PN532_TXD),                // PN532 HSU Tx
  AGPIO(GPIO_PN532_RXD),                // PN532 HSU Rx
#endif
#ifdef USE_TASMOTA_CLIENT               // xdrv_31_tasmota_client.ino
  AGPIO(GPIO_TASMOTACLIENT_TXD),        // Tasmota Client TX
  AGPIO(GPIO_TASMOTACLIENT_RXD),        // Tasmota Client RX
  AGPIO(GPIO_TASMOTACLIENT_RST),        // Tasmota Client Reset
  AGPIO(GPIO_TASMOTACLIENT_RST_INV),    // Tasmota Client Reset Inverted
#endif
#ifdef USE_RDM6300                      // xsns_51_rdm6300.ino
  AGPIO(GPIO_RDM6300_RX),
#endif
#ifdef USE_IBEACON                      // xsns_52_ibeacon.ino
  AGPIO(GPIO_IBEACON_TX),
  AGPIO(GPIO_IBEACON_RX),
#endif
#ifdef USE_GPS                          // xsns_60_gps.ino
  AGPIO(GPIO_GPS_TX),                   // GPS serial interface
  AGPIO(GPIO_GPS_RX),                   // GPS serial interface
#endif
#ifdef USE_HM10                         // xsns_62_mi_hm10.ino
  AGPIO(GPIO_HM10_TX),                  // HM10 serial interface
  AGPIO(GPIO_HM10_RX),                  // HM10 serial interface
#endif
#ifdef USE_OPENTHERM                    // xsns_69_opentherm.ino
  AGPIO(GPIO_BOILER_OT_TX),
  AGPIO(GPIO_BOILER_OT_RX),
#endif
#ifdef USE_AS608                        // xsns_79_as608.ino
  AGPIO(GPIO_AS608_TX),
  AGPIO(GPIO_AS608_RX),
#endif
#ifdef USE_GM861                        // xsns_107_gm861.ino
  AGPIO(GPIO_GM861_TX),
  AGPIO(GPIO_GM861_RX),
#endif
#ifdef USE_HRG15                        // xsns_90_hrg15.ino
  AGPIO(GPIO_HRG15_TX),
  AGPIO(GPIO_HRG15_RX),
#endif
#ifdef USE_CM110x                       // xsns_95_cm110x.ino
  AGPIO(GPIO_CM11_TXD),                 // CM110x Serial interface
  AGPIO(GPIO_CM11_RXD),                 // CM110x Serial interface
#endif
#ifdef USE_LD2410                       // xsns_102_ld2410.ino
  AGPIO(GPIO_LD2410_TX),                // HLK-LD2410 Serial interface
  AGPIO(GPIO_LD2410_RX),                // HLK-LD2410 Serial interface
#endif
#ifdef USE_LOX_O2                       // xsns_105_lox_o2.ino
  AGPIO(GPIO_LOX_O2_RX),                // LuminOx Oxygen Sensor LOX-O2 Serial interface
#endif

/*-------------------------------------------------------------------------------------------*\
 * Other sensors
\*-------------------------------------------------------------------------------------------*/

#ifdef USE_MGC3130
  AGPIO(GPIO_MGC3130_XFER),
  AGPIO(GPIO_MGC3130_RESET),
#endif
#ifdef USE_MAX31855
  AGPIO(GPIO_MAX31855CS) + MAX_MAX31855S, //MAX31855 Serial interface
  AGPIO(GPIO_MAX31855CLK),              // MAX31855 Serial interface
  AGPIO(GPIO_MAX31855DO),               // MAX31855 Serial interface
#endif
#ifdef USE_HRE
  AGPIO(GPIO_HRE_CLOCK),
  AGPIO(GPIO_HRE_DATA),
#endif
#ifdef USE_A4988_STEPPER
  AGPIO(GPIO_A4988_DIR),                // A4988 direction pin
  AGPIO(GPIO_A4988_STP),                // A4988 step pin
  // folowing are not mandatory
  AGPIO(GPIO_A4988_ENA),                // A4988 enabled pin
  AGPIO(GPIO_A4988_MS1) + MAX_A4988_MSS,  // A4988 microstep pin1 to pin3
#endif
#ifdef USE_DEEPSLEEP
  AGPIO(GPIO_DEEPSLEEP),
#endif
#ifdef USE_KEELOQ
  AGPIO(GPIO_CC1101_GDO0),              // CC1101 pin for RX
  AGPIO(GPIO_CC1101_GDO2),              // CC1101 pin for RX
#endif
#ifdef USE_HRXL
  AGPIO(GPIO_HRXL_RX),
#endif
#ifdef USE_DYP
  AGPIO(GPIO_DYP_RX),
#endif
#ifdef USE_AS3935
  AGPIO(GPIO_AS3935),                   // AS3935 IRQ Pin
#endif
#ifdef USE_TELEINFO
  AGPIO(GPIO_TELEINFO_RX),
  AGPIO(GPIO_TELEINFO_ENABLE),
#endif
#ifdef USE_MIEL_HVAC
  AGPIO(GPIO_MIEL_HVAC_TX),             // Mitsubishi Electric HVAC TX pin
  AGPIO(GPIO_MIEL_HVAC_RX),             // Mitsubishi Electric HVAC RX pin
#endif
#ifdef USE_TUYAMCUBR
  AGPIO(GPIO_TUYAMCUBR_TX),
  AGPIO(GPIO_TUYAMCUBR_RX),
#endif
#ifdef USE_WIEGAND
  AGPIO(GPIO_WIEGAND_D0),               // Date line D0 of Wiegand devices
  AGPIO(GPIO_WIEGAND_D1),               // Date line D1 of Wiegand devices
#endif
#ifdef USE_NEOPOOL
  AGPIO(GPIO_NEOPOOL_TX),               // Sugar Valley RS485 Interface
  AGPIO(GPIO_NEOPOOL_RX),               // Sugar Valley RS485 Interface
#endif
#ifdef USE_PROJECTOR_CTRL
  AGPIO(GPIO_PROJECTOR_CTRL_TX),        // LCD/DLP Projector Serial Control
  AGPIO(GPIO_PROJECTOR_CTRL_RX),        // LCD/DLP Projector Serial Control
#endif
#if defined(USE_VL53L0X) or defined (USE_VL53L1X)
  AGPIO(GPIO_VL53LXX_XSHUT1) + VL53LXX_MAX_SENSORS,  // When using multiple VL53LXX.
#endif
#ifdef USE_FLOWRATEMETER
  AGPIO(GPIO_FLOWRATEMETER_IN) + MAX_FLOWRATEMETER, // Flow meter Pin
#endif

#ifdef USE_SHIFT595
  AGPIO(GPIO_SHIFT595_SRCLK),           // 74x595 shift register
  AGPIO(GPIO_SHIFT595_RCLK),
  AGPIO(GPIO_SHIFT595_OE),
  AGPIO(GPIO_SHIFT595_SER),
#endif

#if defined (ESP32) && defined(USE_DINGTIAN_RELAY)
  AGPIO(GPIO_DINGTIAN_CLK) + MAX_DINGTIAN_SHIFT, // Dingtian Relay board - 8,16,24 or 32 relays & inputs
  AGPIO(GPIO_DINGTIAN_SDI),
  AGPIO(GPIO_DINGTIAN_Q7),
  AGPIO(GPIO_DINGTIAN_PL),
  AGPIO(GPIO_DINGTIAN_OE),
  AGPIO(GPIO_DINGTIAN_RCK),
#endif

#ifdef USE_MAGIC_SWITCH
  AGPIO(GPIO_MAGIC_SWITCH) + MAX_MAGIC_SWITCH_MODES,
#endif

#ifdef USE_PIPSOLAR                       // xdrv_92_pipsolar.ino
  AGPIO(GPIO_PIPSOLAR_TX),                // pipsolar inverter Serial interface
  AGPIO(GPIO_PIPSOLAR_RX),                // pipsolar inverter Serial interface
#endif

/*-------------------------------------------------------------------------------------------*\
 * ESP32 specifics
\*-------------------------------------------------------------------------------------------*/

#ifdef ESP32
#if CONFIG_IDF_TARGET_ESP32
  AGPIO(GPIO_HALLEFFECT) + 2,           // Hall effect sensor connected to GPIO36 and 39
#endif  // CONFIG_IDF_TARGET_ESP32
#ifdef USE_WEBCAM
  AGPIO(GPIO_WEBCAM_PWDN),
  AGPIO(GPIO_WEBCAM_RESET),
  AGPIO(GPIO_WEBCAM_XCLK),
  AGPIO(GPIO_WEBCAM_SIOD),
  AGPIO(GPIO_WEBCAM_SIOC),
  AGPIO(GPIO_WEBCAM_DATA) + MAX_WEBCAM_DATA,
  AGPIO(GPIO_WEBCAM_VSYNC),
  AGPIO(GPIO_WEBCAM_HREF),
  AGPIO(GPIO_WEBCAM_PCLK),
  AGPIO(GPIO_WEBCAM_PSCLK),
  AGPIO(GPIO_WEBCAM_HSD) + MAX_WEBCAM_HSD,
  AGPIO(GPIO_WEBCAM_PSRCS),
#endif  // USE_WEBCAM
#ifdef USE_ETHERNET
  AGPIO(GPIO_ETH_PHY_POWER),
  AGPIO(GPIO_ETH_PHY_MDC),
  AGPIO(GPIO_ETH_PHY_MDIO),             // Ethernet
#endif  // USE_ETHERNET

/*-------------------------------------------------------------------------------------------*\
 * ESP32 multiple Analog / Digital converter inputs
\*-------------------------------------------------------------------------------------------*/

  AGPIO(GPIO_ADC_INPUT) + MAX_ADCS,     // Analog inputs
  AGPIO(GPIO_ADC_TEMP) + MAX_ADCS,      // Thermistor
  AGPIO(GPIO_ADC_LIGHT) + MAX_ADCS,     // Light sensor
  AGPIO(GPIO_ADC_BUTTON) + MAX_KEYS,    // Button
  AGPIO(GPIO_ADC_BUTTON_INV) + MAX_KEYS,
  AGPIO(GPIO_ADC_RANGE) + MAX_ADCS,     // Range
  AGPIO(GPIO_ADC_CT_POWER) + MAX_ADCS,  // Current
  AGPIO(GPIO_ADC_JOY) + MAX_ADCS,       // Joystick
  AGPIO(GPIO_ADC_PH) + MAX_ADCS,        // Analog PH Sensor
  AGPIO(GPIO_ADC_MQ) + MAX_ADCS,        // Analog MQ Sensor

#ifdef USE_BIOPDU
  AGPIO(GPIO_BIOPDU_PZEM0XX_TX),  // Biomine BioPDU pins
  AGPIO(GPIO_BIOPDU_PZEM016_RX),
  AGPIO(GPIO_BIOPDU_BIT) + 3,
#endif
#endif  // ESP32
};

/*-------------------------------------------------------------------------------------------*\
 * ESP8266 single Analog / Digital converter input
\*-------------------------------------------------------------------------------------------*/

#ifdef ESP8266
const uint16_t kAdcNiceList[] PROGMEM = {
  GPIO_NONE,                              // Not used
  AGPIO(GPIO_ADC_INPUT),                  // Analog inputs
  AGPIO(GPIO_ADC_TEMP),                   // Thermistor
  AGPIO(GPIO_ADC_LIGHT),                  // Light sensor
  AGPIO(GPIO_ADC_BUTTON) + MAX_KEYS,      // Button
  AGPIO(GPIO_ADC_BUTTON_INV) + MAX_KEYS,
  AGPIO(GPIO_ADC_RANGE),                  // Range
  AGPIO(GPIO_ADC_CT_POWER),               // Current
  AGPIO(GPIO_ADC_JOY),                    // Joystick
  AGPIO(GPIO_ADC_PH),                     // Analog PH Sensor
  AGPIO(GPIO_ADC_MQ),                     // Analog MQ Sensor
};
#endif  // ESP8266

// User selectable ADC functionality
enum UserSelectableAdc {
  ADC_NONE,           // Not used
  ADC_INPUT,          // Analog input
  ADC_TEMP,           // Thermistor
  ADC_LIGHT,          // Light sensor
  ADC_BUTTON,         // Button
  ADC_BUTTON_INV,
  ADC_RANGE,          // Range
  ADC_CT_POWER,       // Current
  ADC_JOY,            // Joystick
  ADC_PH,             // Analog PH Sensor
  ADC_MQ,             // Analog MQ Sensor
//  ADC_SWITCH,         // Switch
//  ADC_SWITCH_INV,
  ADC_END };

/*********************************************************************************************\
 * ATTENTION: No user changeable features beyond this point - do not add templates !!!
\*********************************************************************************************/

#define GPIO_ANY           32   // Any GPIO

#ifdef ESP8266

#define MAX_GPI8_PIN       17   // Number of supported GPIO (0..16)
#define FLASH_PINS         6    // Number of flash chip pins

#define MAX_GPIO_PIN       18   // Number of supported GPIO (0..16 + ADC0)
#define ADC0_PIN           17   // Pin number of ADC0
#define MIN_FLASH_PINS     4    // Number of flash chip pins unusable for configuration (GPIO6, 7, 8 and 11)
#define MAX_USER_PINS      14   // MAX_GPIO_PIN - MIN_FLASH_PINS
#define WEMOS_MODULE       17   // Wemos module

const char PINS_WEMOS[] PROGMEM = "D3TXD4RXD2D1flashcFLFLolD6D7D5D8D0A0";

typedef struct MYIO8 {
  uint8_t      io[MAX_GPI8_PIN];
} myio8;                        // 17 bytes

typedef struct MYCFGIO8285 {
  uint8_t      io[MAX_GPI8_PIN - MIN_FLASH_PINS];
} mycfgio8285;                  // 13 bytes

typedef struct MYTMPLT8285 {
  mycfgio8285  gp;
  uint8_t      flag;
} mytmplt8285;                  // 14 bytes

typedef struct MYCFGIO8266 {
  uint8_t      io[MAX_GPI8_PIN - FLASH_PINS];
} mycfgio8266;                  // 11 bytes

typedef struct MYTMPLT8266 {
  mycfgio8266  gp;
  uint8_t      flag;
} mytmplt8266;                  // 12 bytes

#endif  // ESP8266

#ifdef ESP32
#if CONFIG_IDF_TARGET_ESP32C2

/* ****************************************
 * ESP32C2
 * ****************************************/
#define MAX_GPIO_PIN       21   // Number of supported GPIO
#define MIN_FLASH_PINS     0    // Number of flash chip pins unusable for configuration (GPIO11 to 17)
#define MAX_USER_PINS      21   // MAX_GPIO_PIN - MIN_FLASH_PINS
#define WEMOS_MODULE       0    // Wemos module

//                                  0 1 2 3 4 5 6 7 8 91011121314151617181920
const char PINS_WEMOS[] PROGMEM = "AOAOAOAOAOIOIOIOIOIOIOFLFLFLFLFLFLFLIORXTX";

#elif CONFIG_IDF_TARGET_ESP32C3

/* ****************************************
 * ESP32C3
 * ****************************************/
#define MAX_GPIO_PIN       22   // Number of supported GPIO
#define MIN_FLASH_PINS     0    // Number of flash chip pins unusable for configuration (GPIO11 to 17)
#define MAX_USER_PINS      22   // MAX_GPIO_PIN - MIN_FLASH_PINS
#define WEMOS_MODULE       0    // Wemos module

//                                  0 1 2 3 4 5 6 7 8 9101112131415161718192021
const char PINS_WEMOS[] PROGMEM = "AOAOAOAOAOAOIOIOIOIOIOFLFLFLFLFLFLFLIOIORXTX";

#elif CONFIG_IDF_TARGET_ESP32C6

/* ****************************************
 * ESP32C6
 * ****************************************/
#define MAX_GPIO_PIN       31   // Number of supported GPIO
#define MIN_FLASH_PINS     0    // Number of flash chip pins unusable for configuration (GPIO24 to 30)
#define MAX_USER_PINS      31   // MAX_GPIO_PIN - MIN_FLASH_PINS
#define WEMOS_MODULE       0    // Wemos module

//                                  0 1 2 3 4 5 6 7 8 9101112131415161718192021222324252627282930
const char PINS_WEMOS[] PROGMEM = "AOAOAOAOAOAOAOIOIOIOIOIOIOIOIOIOTXRXIOIOIOIOIOIOFLFLFLFLFLFLFL";

#elif CONFIG_IDF_TARGET_ESP32S2

/* ****************************************
 * ESP32S2
 * ****************************************/
#define MAX_GPIO_PIN       47   // Number of supported GPIO
#define MIN_FLASH_PINS     11   // Number of flash chip pins unusable for configuration (22-25 don't exist, 26-32 for SPI)
#define MAX_USER_PINS      36   // MAX_GPIO_PIN - MIN_FLASH_PINS
#define WEMOS_MODULE       0    // Wemos module

//                                  0 1 2 3 4 5 6 7 8 910111213141516171819202122232425262728293031323334353637383940414243444546
const char PINS_WEMOS[] PROGMEM = "IOAOAOAOAOAOAOAOAOAOAOAOAOAOAOAOAOAOAOAOAOIO--------FLFLFLFLFLFLFLIOIOIOIOIOIOIOIOIOIOIOIOIOI ";

#elif CONFIG_IDF_TARGET_ESP32S3
/* ****************************************
 * ESP32S3
 * GPIOs 0..21 + 33..48
 * - 22..25 are not used
 * - 26..32 are used for SPI Flash
 * - 33..37 are used by PSRAM
 * ****************************************/
#define MAX_GPIO_PIN       49   // Number of supported GPIO, 0..48
#define MIN_FLASH_PINS     11   // Number of flash chip pins unusable for configuration (22-25 don't exist, 26-32 for SPI)
#define MAX_USER_PINS      38   // MAX_GPIO_PIN - MIN_FLASH_PINS
#define WEMOS_MODULE       0    // Wemos module

//                                  0 1 2 3 4 5 6 7 8 9101112131415161718192021222324252627282930313233343536373839404142434445464748
const char PINS_WEMOS[] PROGMEM = "IOAOAOAOAOAOAOAOAOAOAOAOAOAOAOAOAOAOAOAOAOIO--------FLFLFLFLFLFLFLIOIOIOIOIOIOIOIOIOIOIOIOIOIOIOIO";

#else  // not CONFIG_IDF_TARGET_ESP32C2/C3/C6 nor CONFIG_IDF_TARGET_ESP32S2 - ESP32

/* ****************************************
 * ESP32 - including Pico
 *
 * The initial template was 0-5 9-10 12-39
 * New template covers 0-27 32-39
 * However to maintain backwards compatibility, the following mapping occures
 * Template GPIO | Phyiscal GPIO
 *   28          |  6
 *   29          |  7
 *   30          |  8
 *   31          |  11
 * ****************************************/
// Conversion table
#define ESP32_TEMPLATE_TO_PHY         \
   0,  1,  2,  3,  4,  5,             \
   9, 10,                             \
  12, 13, 14, 15, 16, 17, 18, 19,     \
  20, 21, 22, 23, 24, 25, 26, 27,     \
   6,  7,  8, 11,      /* 28-31 */    \
  32, 33, 34, 35, 36, 37, 38, 39

#define MAX_GPIO_PIN       40   // Number of supported GPIO
#define MIN_FLASH_PINS     4    // Number of flash chip pins unusable for configuration (GPIO6, 7, 8 and 11)
#define MAX_USER_PINS      36   // MAX_GPIO_PIN - MIN_FLASH_PINS
#define WEMOS_MODULE       0    // Wemos module

//                                  0 1 2 3 4 5 6 7 8 9101112131415161718192021222324252627282930313233343536373839
const char PINS_WEMOS[] PROGMEM = "IOTXIORXIOIOFLFLFLFLFLFLIOIOIOIOIOIOIOIOIOIOIOIOIOIOIOIO--------AOAOIAIAIAIAIAIA";

#endif  // ESP32/S2/C2/C3/C6 selection
#endif  // ESP32

/********************************************************************************************\
 * !!! Changes in below type sizes impact Settings layout - Add fill bytes in Settings !!!
\********************************************************************************************/

typedef struct MYIO {
  uint16_t      io[MAX_GPIO_PIN];
} myio;                         // ESP8266: 18*2 = 36 bytes / ESP32: 40*2 = 80 bytes / ESP32-C3: 22*2 = 44 bytes / ESP32-S2: 47*2 = 94 bytes / ESP32-S3: 49*2 = 98 bytes

typedef struct MYCFGIO {
  uint16_t      io[MAX_USER_PINS];
} mycfgio;                      // ESP8266: 14*2 = 28 bytes / ESP32: 36*2 = 72 bytes / ESP32-C3: 22*2 = 44 bytes / ESP32-S2: 36*2 = 72 bytes / ESP32-S3: 33*2 = 66 bytes

#define GPIO_FLAG_USED       0  // Currently no flags used

typedef union {
  uint16_t data;
  struct {
    uint16_t spare00 : 1;
    uint16_t spare01 : 1;
    uint16_t spare02 : 1;
    uint16_t spare03 : 1;
    uint16_t spare04 : 1;
    uint16_t spare05 : 1;
    uint16_t spare06 : 1;
    uint16_t spare07 : 1;
    uint16_t spare08 : 1;
    uint16_t spare09 : 1;
    uint16_t spare10 : 1;
    uint16_t spare11 : 1;
    uint16_t spare12 : 1;
    uint16_t spare13 : 1;
    uint16_t spare14 : 1;
    uint16_t spare15 : 1;
  };
} gpio_flag;                    // 2 bytes

typedef struct MYTMPLT {
  mycfgio      gp;              // 28 / 72 / 44 / 72 bytes
  gpio_flag    flag;            // 2 bytes
} mytmplt;                      // 30 / 74 / 46 / 74 bytes

//********************************************************************************************

#ifdef ESP8266
#include "include/tasmota_template_legacy.h"

/********************************************************************************************\
 * ESP8266 Module Templates
\********************************************************************************************/

#define USER_MODULE        255

// Supported ESP8266 hardware modules
enum SupportedModulesESP8266 {
  SONOFF_BASIC, SONOFF_RF, SONOFF_SV, SONOFF_TH, SONOFF_DUAL, SONOFF_POW, SONOFF_4CH, SONOFF_S2X, SLAMPHER, SONOFF_TOUCH,
  SONOFF_LED, CH1, CH4, MOTOR, ELECTRODRAGON, EXS_RELAY, WION, WEMOS, SONOFF_DEV, H801,
  SONOFF_SC, SONOFF_BN, SONOFF_4CHPRO, HUAFAN_SS, SONOFF_BRIDGE, SONOFF_B1, AILIGHT, SONOFF_T11, SONOFF_T12, SONOFF_T13,
  SUPLA1, WITTY, YUNSHAN, MAGICHOME, LUANIHVIO, KMC_70011, ARILUX_LC01, ARILUX_LC11, SONOFF_DUAL_R2, ARILUX_LC06,
  SONOFF_S31, ZENGGE_ZF_WF017, SONOFF_POW_R2, SONOFF_IFAN02, BLITZWOLF_BWSHP, SHELLY1, SHELLY2, PHILIPS, NEO_COOLCAM, ESP_SWITCH,
  OBI, TECKIN, APLIC_WDP303075, TUYA_DIMMER, GOSUND, ARMTRONIX_DIMMERS, SK03_TUYA, PS_16_DZ, TECKIN_US, MANZOKU_EU_4,
  OBI2, YTF_IR_BRIDGE, DIGOO, KA10, ZX2820, MI_DESK_LAMP, SP10, WAGA, SYF05, SONOFF_L1,
  SONOFF_IFAN03, EXS_DIMMER, PWM_DIMMER, SONOFF_D1, SONOFF_ZB_BRIDGE,
  MAXMODULE };

const char kModuleNames[] PROGMEM =
  "Sonoff Basic|Sonoff RF|Sonoff SV|Sonoff TH|Sonoff Dual|Sonoff Pow|Sonoff 4CH|Sonoff S2X|Slampher|Sonoff Touch|"
  "Sonoff LED|1 Channel|4 Channel|Motor C/AC|ElectroDragon|EXS Relay(s)|WiOn|Generic|Sonoff Dev|H801|"
  "Sonoff SC|Sonoff BN-SZ|Sonoff 4CH Pro|Huafan SS|Sonoff Bridge|Sonoff B1|AiLight|Sonoff T1 1CH|Sonoff T1 2CH|Sonoff T1 3CH|"
  "Supla Espablo|Witty Cloud|Yunshan Relay|MagicHome|Luani HVIO|KMC 70011|Arilux LC01|Arilux LC11|Sonoff Dual R2|Arilux LC06|"
  "Sonoff S31|Zengge WF017|Sonoff Pow R2|Sonoff iFan02|BlitzWolf SHP|Shelly 1|Shelly 2|Xiaomi Philips|Neo Coolcam|ESP Switch|"
  "OBI Socket|Teckin|AplicWDP303075|Tuya MCU|Gosund SP1 v23|ARMTR Dimmer|SK03 Outdoor|PS-16-DZ|Teckin US|Manzoku strip|"
  "OBI Socket 2|YTF IR Bridge|Digoo DG-SP202|KA10|Luminea ZX2820|Mi Desk Lamp|SP10|WAGA CHCZ02MB|SYF05|Sonoff L1|"
  "Sonoff iFan03|EXS Dimmer|PWM Dimmer|Sonoff D1|Sonoff ZbBridge"
  ;

const uint8_t kModuleNiceList[] PROGMEM = {
  SONOFF_BASIC,        // Sonoff Relay Devices
  SONOFF_RF,
  SONOFF_TH,
  SONOFF_DUAL,
  SONOFF_DUAL_R2,
  SONOFF_POW,
  SONOFF_POW_R2,
  SONOFF_4CH,
  SONOFF_4CHPRO,
  SONOFF_S31,          // Sonoff Socket Relay Devices with Energy Monitoring
  SONOFF_S2X,          // Sonoff Socket Relay Devices
  SONOFF_TOUCH,        // Sonoff Switch Devices
  SONOFF_T11,
  SONOFF_T12,
  SONOFF_T13,
#ifdef USE_SONOFF_D1
  SONOFF_D1,           // Sonoff D1
#endif
  SONOFF_LED,          // Sonoff Light Devices
  SONOFF_BN,
#ifdef USE_SONOFF_L1
  SONOFF_L1,
#endif
  SONOFF_B1,           // Sonoff Light Bulbs
  SLAMPHER,
#ifdef USE_SONOFF_SC
  SONOFF_SC,           // Sonoff Environmemtal Sensor
#endif
#ifdef USE_SONOFF_IFAN
  SONOFF_IFAN02,       // Sonoff Fan
  SONOFF_IFAN03,
#endif
#ifdef USE_SONOFF_RF
  SONOFF_BRIDGE,       // Sonoff Bridge
#endif
#ifdef USE_ZIGBEE_EZSP
  SONOFF_ZB_BRIDGE,
#endif
  SONOFF_SV,           // Sonoff Development Devices
  SONOFF_DEV,
  CH1,                 // Relay Devices
  CH4,
  MOTOR,
  ELECTRODRAGON,
  EXS_RELAY,
  SUPLA1,
  LUANIHVIO,
  YUNSHAN,
  WION,
  SHELLY1,
  SHELLY2,
  BLITZWOLF_BWSHP,     // Socket Relay Devices with Energy Monitoring
  TECKIN,
  TECKIN_US,
  APLIC_WDP303075,
  GOSUND,
  ZX2820,
  SK03_TUYA,
  DIGOO,
  KA10,
  SP10,
  WAGA,
  NEO_COOLCAM,         // Socket Relay Devices
  OBI,
  OBI2,
  MANZOKU_EU_4,
  ESP_SWITCH,          // Switch Devices
#ifdef USE_TUYA_MCU
  TUYA_DIMMER,         // Dimmer Devices
#endif
#ifdef USE_ARMTRONIX_DIMMERS
  ARMTRONIX_DIMMERS,
#endif
#ifdef USE_PS_16_DZ
  PS_16_DZ,
#endif
#ifdef USE_EXS_DIMMER
  EXS_DIMMER,
#endif
#ifdef USE_PWM_DIMMER
  PWM_DIMMER,
#endif
  H801,                // Light Devices
  MAGICHOME,
  ARILUX_LC01,
  ARILUX_LC06,
  ARILUX_LC11,
  ZENGGE_ZF_WF017,
  HUAFAN_SS,
#ifdef ROTARY_V1
  MI_DESK_LAMP,
#endif
  KMC_70011,
  AILIGHT,             // Light Bulbs
  PHILIPS,
  SYF05,
  YTF_IR_BRIDGE,
  WITTY,               // Development Devices
  WEMOS
};

enum SupportedTemplates8285 {
  TMP_SONOFF_BASIC, TMP_SONOFF_SV, TMP_SONOFF_DUAL, TMP_SONOFF_POW, TMP_SONOFF_LED, TMP_ELECTRODRAGON,
  TMP_EXS_RELAY, TMP_WION, TMP_SONOFF_DEV, TMP_H801, TMP_SONOFF_SC, TMP_SONOFF_BN, TMP_HUAFAN_SS, TMP_SONOFF_BRIDGE,
  TMP_SONOFF_B1, TMP_AILIGHT, TMP_SONOFF_T11, TMP_SUPLA1, TMP_WITTY, TMP_YUNSHAN, TMP_MAGICHOME,
  TMP_LUANIHVIO, TMP_KMC_70011, TMP_ARILUX_LC01, TMP_ARILUX_LC11, TMP_ARILUX_LC06, TMP_ZENGGE_ZF_WF017,
  TMP_SONOFF_POW_R2, TMP_BLITZWOLF_BWSHP, TMP_SHELLY1, TMP_SHELLY2, TMP_PHILIPS, TMP_NEO_COOLCAM, TMP_ESP_SWITCH, TMP_OBI,
  TMP_TECKIN, TMP_APLIC_WDP303075, TMP_TUYA_DIMMER, TMP_GOSUND, TMP_ARMTRONIX_DIMMERS, TMP_SK03_TUYA, TMP_PS_16_DZ,
  TMP_TECKIN_US, TMP_MANZOKU_EU_4, TMP_OBI2, TMP_YTF_IR_BRIDGE, TMP_DIGOO, TMP_KA10, TMP_ZX2820, TMP_MI_DESK_LAMP, TMP_SP10,
  TMP_WAGA, TMP_SYF05, TMP_EXS_DIMMER, TMP_PWM_DIMMER, TMP_SONOFF_ZB_BRIDGE,
  TMP_MAXMODULE_8285 };

enum SupportedTemplates8266 {
  TMP_WEMOS = TMP_MAXMODULE_8285, TMP_SONOFF_4CH, TMP_SONOFF_T12, TMP_SONOFF_T13, TMP_SONOFF_DUAL_R2, TMP_SONOFF_IFAN03,
  TMP_MAXMODULE_8266 };

const uint8_t kModuleTemplateList[MAXMODULE] PROGMEM = {
  TMP_SONOFF_BASIC,
  TMP_SONOFF_BASIC,     // SONOFF_RF
  TMP_SONOFF_SV,
  TMP_SONOFF_BASIC,     // SONOFF_TH
  TMP_SONOFF_DUAL,
  TMP_SONOFF_POW,
  TMP_SONOFF_4CH,
  TMP_SONOFF_BASIC,     // SONOFF_S2X
  TMP_SONOFF_BASIC,     // SLAMPHER
  TMP_SONOFF_T11,       // SONOFF_TOUCH
  TMP_SONOFF_LED,
  TMP_SONOFF_BASIC,     // CH1
  TMP_SONOFF_DUAL,      // CH4
  TMP_SONOFF_BASIC,     // MOTOR
  TMP_ELECTRODRAGON,
  TMP_EXS_RELAY,
  TMP_WION,
  TMP_WEMOS,
  TMP_SONOFF_DEV,
  TMP_H801,
  TMP_SONOFF_SC,
  TMP_SONOFF_BN,
  TMP_SONOFF_4CH,       // SONOFF_4CHPRO
  TMP_HUAFAN_SS,
  TMP_SONOFF_BRIDGE,
  TMP_SONOFF_B1,
  TMP_AILIGHT,
  TMP_SONOFF_T11,
  TMP_SONOFF_T12,
  TMP_SONOFF_T13,
  TMP_SUPLA1,
  TMP_WITTY,
  TMP_YUNSHAN,
  TMP_MAGICHOME,
  TMP_LUANIHVIO,
  TMP_KMC_70011,
  TMP_ARILUX_LC01,
  TMP_ARILUX_LC11,
  TMP_SONOFF_DUAL_R2,
  TMP_ARILUX_LC06,
  TMP_SONOFF_POW_R2,    // SONOFF_S31
  TMP_ZENGGE_ZF_WF017,
  TMP_SONOFF_POW_R2,
  TMP_SONOFF_4CH,       // SONOFF_IFAN02
  TMP_BLITZWOLF_BWSHP,
  TMP_SHELLY1,
  TMP_SHELLY2,
  TMP_PHILIPS,
  TMP_NEO_COOLCAM,
  TMP_ESP_SWITCH,
  TMP_OBI,
  TMP_TECKIN,
  TMP_APLIC_WDP303075,
  TMP_TUYA_DIMMER,
  TMP_GOSUND,
  TMP_ARMTRONIX_DIMMERS,
  TMP_SK03_TUYA,
  TMP_PS_16_DZ,
  TMP_TECKIN_US,
  TMP_MANZOKU_EU_4,
  TMP_OBI2,
  TMP_YTF_IR_BRIDGE,
  TMP_DIGOO,
  TMP_KA10,
  TMP_ZX2820,
  TMP_MI_DESK_LAMP,
  TMP_SP10,
  TMP_WAGA,
  TMP_SYF05,
  TMP_SONOFF_DUAL,      // SONOFF_L1
  TMP_SONOFF_IFAN03,
  TMP_EXS_DIMMER,
  TMP_PWM_DIMMER,
  TMP_SONOFF_DUAL,      // SONOFF_D1
  TMP_SONOFF_ZB_BRIDGE,
  };

/*********************************************************************************************\
 * Templates with 12 usable pins (ESP8266)
\*********************************************************************************************/

const mytmplt8266 kModules8266[TMP_MAXMODULE_8285] PROGMEM = {
  {                     // SONOFF_BASIC - Sonoff Basic (ESP8266)
    GPI8_KEY1,          // GPIO00 Button
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    GPI8_USER,          // GPIO02 Only available on newer Sonoff Basic R2 V1
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    GPI8_USER,          // GPIO04 Optional sensor
    0,                  // GPIO05
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL1,          // GPIO12 Red Led and Relay (0 = Off, 1 = On)
    GPI8_LED1_INV,      // GPIO13 Green Led (0 = On, 1 = Off) - Link and Power status
    GPI8_USER,          // GPIO14 Optional sensor
    0,                  // GPIO15
    0,                  // GPIO16
    0                   // ADC0 Analog input
  },
  {                     // SONOFF_SV - Sonoff SV (ESP8266)
    GPI8_KEY1,          // GPIO00 Button
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    0,
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    GPI8_USER,          // GPIO04 Optional sensor
    GPI8_USER,          // GPIO05 Optional sensor
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL1,          // GPIO12 Red Led and Relay (0 = Off, 1 = On)
    GPI8_LED1_INV,      // GPIO13 Green Led (0 = On, 1 = Off) - Link and Power status
    GPI8_USER,          // GPIO14 Optional sensor
    0, 0,
    GPI8_USER           // ADC0 Analog input
  },
  {                     // SONOFF_DUAL - Sonoff Dual (ESP8266)
    GPI8_USER,          // GPIO00 Pad
    GPI8_TXD,           // GPIO01 Relay control
    0,
    GPI8_RXD,           // GPIO03 Relay control
    GPI8_USER,          // GPIO04 Optional sensor
    0,
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    0,
    GPI8_LED1_INV,      // GPIO13 Blue Led (0 = On, 1 = Off) - Link and Power status
    GPI8_USER,          // GPIO14 Optional sensor
    0, 0, 0
  },
  {                     // SONOFF_POW - Sonoff Pow (ESP8266 - HLW8012)
    GPI8_KEY1,          // GPIO00 Button
    0, 0, 0, 0,
    GPI8_NRG_SEL,       // GPIO05 HLW8012 Sel output (1 = Voltage)
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL1,          // GPIO12 Red Led and Relay (0 = Off, 1 = On)
    GPI8_NRG_CF1,       // GPIO13 HLW8012 CF1 voltage / current
    GPI8_HLW_CF,        // GPIO14 HLW8012 CF power
    GPI8_LED1,          // GPIO15 Blue Led (0 = On, 1 = Off) - Link and Power status
    0, 0
  },
  {                     // SONOFF_LED - Sonoff LED (ESP8266)
    GPI8_KEY1,          // GPIO00 Button
    0, 0, 0,
    GPI8_USER,          // GPIO04 Optional sensor (PWM3 Green)
    GPI8_USER,          // GPIO05 Optional sensor (PWM2 Red)
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_PWM1,          // GPIO12 Cold light (PWM0 Cold)
    GPI8_LED1_INV,      // GPIO13 Blue Led (0 = On, 1 = Off) - Link and Power status
    GPI8_PWM2,          // GPIO14 Warm light (PWM1 Warm)
    GPI8_USER,          // GPIO15 Optional sensor (PWM4 Blue)
    0, 0
  },
  {                     // ELECTRODRAGON - ElectroDragon IoT Relay Board (ESP8266)
    GPI8_KEY2,          // GPIO00 Button 2
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    GPI8_KEY1,          // GPIO02 Button 1
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    GPI8_USER,          // GPIO04 Optional sensor
    GPI8_USER,          // GPIO05 Optional sensor
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL2,          // GPIO12 Red Led and Relay 2 (0 = Off, 1 = On)
    GPI8_REL1,          // GPIO13 Red Led and Relay 1 (0 = Off, 1 = On)
    GPI8_USER,          // GPIO14 Optional sensor
    GPI8_USER,          // GPIO15 Optional sensor
    GPI8_LED1,          // GPIO16 Green/Blue Led (1 = On, 0 = Off) - Link and Power status
    GPI8_USER           // ADC0   A0 Analog input
  },
  {                     // EXS_RELAY - ES-Store Latching relay(s) (ESP8266)
                        // https://ex-store.de/ESP8266-WiFi-Relay-V31
                        //   V3.1 Module Pin 1 VCC 3V3, Module Pin 6 GND
                        // https://ex-store.de/2-Kanal-WiFi-WLan-Relay-V5-Blackline-fuer-Unterputzmontage
    GPI8_USER,          // GPIO00 V3.1 Module Pin 8 - V5.0 Module Pin 4
    GPI8_USER,          // GPIO01 UART0_TXD V3.1 Module Pin 2 - V5.0 Module Pin 3
    GPI8_USER,          // GPIO02 V3.1 Module Pin 7
    GPI8_USER,          // GPIO03 UART0_RXD V3.1 Module Pin 3
    GPI8_USER,          // GPIO04 V3.1 Module Pin 10 - V5.0 Module Pin 2
    GPI8_USER,          // GPIO05 V3.1 Module Pin 9 - V5.0 Module Pin 1
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL1,          // GPIO12 Relay1 ( 1 = Off)
    GPI8_REL2,          // GPIO13 Relay1 ( 1 = On)
    GPI8_USER,          // GPIO14 V3.1 Module Pin 5 - V5.0 GPI8_REL3_INV Relay2 ( 1 = Off)
    GPI8_LED1,          // GPIO15 V5.0 LED1 - Link and Power status
    GPI8_USER,          // GPIO16 V3.1 Module Pin 4 - V5.0 GPI8_REL4_INV Relay2 ( 1 = On)
    0
  },
  {                     // WION - Indoor Tap (ESP8266)
                        // https://www.amazon.com/gp/product/B00ZYLUBJU/ref=s9_acsd_al_bw_c_x_3_w
    GPI8_USER,          // GPIO00 Optional sensor (pm clock)
    0,
    GPI8_LED1,          // GPIO02 Green Led (1 = On, 0 = Off) - Link and Power status
    0, 0, 0,
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_USER,          // GPIO12 Optional sensor (pm data)
    GPI8_KEY1,          // GPIO13 Button
    0,
    GPI8_REL1,          // GPIO15 Relay (0 = Off, 1 = On)
    0, 0
  },
  {                     // SONOFF_DEV - Sonoff Dev (ESP8266)
    GPI8_KEY1,          // GPIO00 E-FW Button
    GPI8_USER,          // GPIO01 TX Serial RXD and Optional sensor
    0,                         // GPIO02
    GPI8_USER,          // GPIO03 RX Serial TXD and Optional sensor
    GPI8_USER,          // GPIO04 Optional sensor
    GPI8_USER,          // GPIO05 Optional sensor
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_USER,          // GPIO12
    GPI8_USER,          // GPIO13 BLUE LED
    GPI8_USER,          // GPIO14 Optional sensor
    0,                  // GPIO15
    0,                  // GPIO16
    GPI8_USER           // ADC0 A0 Analog input
  },
  {                     // H801 - Lixada H801 Wifi (ESP8266)
    GPI8_USER,          // GPIO00 E-FW Button
    GPI8_LED1,          // GPIO01 Green LED - Link and Power status
    GPI8_USER,          // GPIO02 TX and Optional sensor - Pin next to TX on the PCB
    GPI8_USER,          // GPIO03 RX and Optional sensor - Pin next to GND on the PCB
    GPI8_PWM5,          // GPIO04 W2 - PWM5
    GPI8_LED2_INV,      // GPIO05 Red LED
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_PWM3,          // GPIO12 Blue
    GPI8_PWM2,          // GPIO13 Green
    GPI8_PWM4,          // GPIO14 W1 - PWM4
    GPI8_PWM1,          // GPIO15 Red
    0, 0
  },
  {                     // SONOFF_SC - onoff SC (ESP8266)
    GPI8_KEY1,          // GPIO00 Button
    GPI8_TXD,           // GPIO01 RXD to ATMEGA328P
    GPI8_USER,          // GPIO02 Optional sensor
    GPI8_RXD,           // GPIO03 TXD to ATMEGA328P
    0, 0,
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    0,
    GPI8_LED1_INV,      // GPIO13 Green Led (0 = On, 1 = Off) - Link and Power status
    0, 0, 0, 0
  },
  {                     // SONOFF_BN - Sonoff BN-SZ01 Ceiling led (ESP8285)
    0, 0, 0, 0, 0, 0,
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_PWM1,          // GPIO12 Light
    GPI8_LED1_INV,      // GPIO13 Red Led (0 = On, 1 = Off) - Link and Power status
    0, 0, 0, 0
  },
  {                     // HUAFAN_SS - Hua Fan Smart Socket (ESP8266) - like Sonoff Pow
    GPI8_LEDLNK_INV,    // GPIO00 Blue Led (0 = On, 1 = Off) - Link status
    0, 0,
    GPI8_LED1_INV,      // GPIO03 Red Led (0 = On, 1 = Off) - Power status
    GPI8_KEY1,          // GPIO04 Button
    GPI8_REL1_INV,      // GPIO05 Relay (0 = On, 1 = Off)
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_NRG_CF1,       // GPIO12 HLW8012 CF1 voltage / current
    GPI8_NRG_SEL,       // GPIO13 HLW8012 Sel output (1 = Voltage)
    GPI8_HLW_CF,        // GPIO14 HLW8012 CF power
    0, 0, 0
  },
  {                     // SONOFF_BRIDGE - Sonoff RF Bridge 433 (ESP8285)
    GPI8_KEY1,          // GPIO00 Button
    GPI8_TXD,           // GPIO01 RF bridge control
    GPI8_USER,          // GPIO02 Optional sensor
    GPI8_RXD,           // GPIO03 RF bridge control
    GPI8_USER,          // GPIO04 Optional sensor
    GPI8_USER,          // GPIO05 Optional sensor
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_USER,          // GPIO12 Optional sensor
    GPI8_LED1_INV,      // GPIO13 Blue Led (0 = On, 1 = Off) - Link and Power status
    GPI8_USER,          // GPIO14 Optional sensor
    0, 0, 0
  },
  {                     // SONOFF_B1 - Sonoff B1 (ESP8285 - my9231)
    GPI8_KEY1,          // GPIO00 Pad
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor pad
    GPI8_USER,          // GPIO02 Optional sensor SDA pad
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor pad
    0, 0,
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_DI,            // GPIO12 my9231 DI
    0,
    GPI8_DCKI,          // GPIO14 my9231 DCKI
    0, 0, 0
  },
  {                     // AILIGHT - Ai-Thinker RGBW led (ESP8266 - my9291)
    GPI8_KEY1,          // GPIO00 Pad
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor pad
    GPI8_USER,          // GPIO02 Optional sensor SDA pad
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor pad
    0, 0,
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    0,
    GPI8_DI,            // GPIO13 my9291 DI
    0,
    GPI8_DCKI,          // GPIO15 my9291 DCKI
    0, 0
  },
  {                     // SONOFF_T11 - Sonoff T1 1CH (ESP8285)
    GPI8_KEY1,          // GPIO00 Button 1
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    GPI8_USER,          // GPIO02 Optional Sensor (J3 Pin 5)
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    0, 0,
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL1,          // GPIO12 Blue Led and Relay 1 (0 = Off, 1 = On)
    GPI8_LED1_INV,      // GPIO13 Blue Led (0 = On, 1 = Off) - Link and Power status
    0, 0, 0, 0
  },
  {                     // SUPLA1 - Supla Espablo (ESP8266)
                        // http://www.wykop.pl/ramka/3325399/diy-supla-do-puszki-instalacyjnej-podtynkowej-supla-org/
    0,                  // GPIO00 Flash jumper
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
#ifdef USE_DS18x20
    GPI8_DSB,           // GPIO02 DS18B20 sensor
#else
    GPI8_USER,          // GPIO02 Optional sensor
#endif
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    GPI8_KEY1,          // GPIO04 Button 1
    GPI8_REL1,          // GPIO05 Relay 1 (0 = Off, 1 = On)
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_USER,          // GPIO12 Optional sensor
    GPI8_REL2,          // GPIO13 Relay 2 (0 = Off, 1 = On)
    GPI8_USER,          // GPIO14 Optional sensor
    0,
    GPI8_LED1,          // GPIO16 Led (1 = On, 0 = Off) - Link and Power status
    GPI8_USER           // ADC0 A0 Analog input
  },
  {                     // WITTY - Witty Cloud Dev Board (ESP8266)
                        // https://www.aliexpress.com/item/ESP8266-serial-WIFI-Witty-cloud-Development-Board-ESP-12F-module-MINI-nodemcu/32643464555.html
    GPI8_USER,          // GPIO00 D3 flash push button on interface board
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    GPI8_LED1_INV,      // GPIO02 D4 Blue Led (0 = On, 1 = Off) on ESP-12F - Link and Power status
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    GPI8_KEY1,          // GPIO04 D2 push button on ESP-12F board
    GPI8_USER,          // GPIO05 D1 optional sensor
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_PWM2,          // GPIO12 D6 RGB LED Green
    GPI8_PWM3,          // GPIO13 D7 RGB LED Blue
    GPI8_USER,          // GPIO14 D5 optional sensor
    GPI8_PWM1,          // GPIO15 D8 RGB LED Red
    GPI8_USER,          // GPIO16 D0 optional sensor
    GPI8_USER           // ADC0 A0 Light sensor / Requires USE_ADC_VCC in user_config.h to be disabled
  },
  {                     // YUNSHAN - Yunshan Wifi Relay (ESP8266)
                        // https://www.ebay.com/p/Esp8266-220v-10a-Network-Relay-WiFi-Module/1369583381
                        // Schematics and Info https://ucexperiment.wordpress.com/2016/12/18/yunshan-esp8266-250v-15a-acdc-network-wifi-relay-module/
    0,                  // GPIO00 Flash jumper - Module Pin 8
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor - Module Pin 2
    GPI8_LED1_INV,      // GPIO02 Blue Led (0 = On, 1 = Off) on ESP-12F - Module Pin 7 - Link and Power status
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor - Module Pin 3
    GPI8_REL1,          // GPIO04 Red Led and Relay (0 = Off, 1 = On) - Module Pin 10
    GPI8_KEY1,          // GPIO05 Blue Led and OptoCoupler input - Module Pin 9
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    0, 0, 0, 0, 0, 0
  },
  {                     // MAGICHOME - Magic Home (aka Flux-light) (ESP8266) and Arilux LC10 (ESP8285)
                        // https://www.aliexpress.com/item/Magic-Home-Mini-RGB-RGBW-Wifi-Controller-For-Led-Strip-Panel-light-Timing-Function-16million-colors/32686853650.html
    0,
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    GPI8_LED1_INV,      // GPIO02 Blue onboard LED - Link and Power status
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    GPI8_ARIRFRCV,      // GPIO04 IR or RF receiver (optional) (Arilux LC10)
    GPI8_PWM2,          // GPIO05 RGB LED Green
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_PWM3,          // GPIO12 RGB LED Blue
    GPI8_USER,          // GPIO13 RGBW LED White (optional - set to PWM4 for Cold White or Warm White as used on Arilux LC10)
    GPI8_PWM1,          // GPIO14 RGB LED Red
    GPI8_ARIRFSEL,      // GPIO15 RF receiver control (Arilux LC10)
    0, 0
  },
  {                     // LUANIHVIO - ESP8266_HVIO
                        // https://luani.de/projekte/esp8266-hvio/
    0,                  // GPIO00 Flash jumper
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    GPI8_USER,          // GPIO02 Optional sensor / I2C SDA pad
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    GPI8_REL1,          // GPIO04 Relay 1 (0 = Off, 1 = On)
    GPI8_REL2,          // GPIO05 Relay 2 (0 = Off, 1 = On)
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_SWT1,          // GPIO12 External input 1 (0 = On, 1 = Off)
    GPI8_SWT2,          // GPIO13 External input 2 (0 = On, 1 = Off)
    GPI8_USER,          // GPIO14 Optional sensor / I2C SCL pad
    GPI8_LED1,          // GPIO15 Led (1 = On, 0 = Off) - Link and Power status
    0,
    GPI8_USER           // ADC0 A0 Analog input
  },
  {                     // KMC_70011 - KMC 70011
                        // https://www.amazon.com/KMC-Timing-Monitoring-Network-125V-240V/dp/B06XRX2GTQ
    GPI8_KEY1,          // GPIO00 Button
    0, 0, 0,
    GPI8_HLW_CF,        // GPIO04 HLW8012 CF power
    GPI8_NRG_CF1,       // GPIO05 HLW8012 CF1 voltage / current
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_NRG_SEL,       // GPIO12 HLW8012 SEL (1 = Voltage)
    GPI8_LED1_INV,      // GPIO13 Green Led - Link and Power status
    GPI8_REL1,          // GPIO14 Relay
    0, 0, 0
  },
  {                     // ARILUX_LC01 - Arilux AL-LC01 (ESP8285)
                        // https://www.banggood.com/nl/ARILUX-AL-LC01-Super-Mini-LED-WIFI-Smart-RGB-Controller-For-RGB-LED-Strip-Light-DC-9-12V-p-1058603.html
                        //  (PwmFrequency 1111Hz)
    GPI8_KEY1,          // GPIO00 Optional Button
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    GPI8_ARIRFSEL,      // GPIO02 RF receiver control
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    GPI8_ARIRFRCV,      // GPIO04 IR or RF receiver (optional)
    GPI8_PWM1,          // GPIO05 RGB LED Red
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_PWM2,          // GPIO12 RGB LED Green
    GPI8_PWM3,          // GPIO13 RGB LED Blue
    GPI8_USER,          // GPIO14 RGBW LED White (optional - set to PWM4 for Cold White or Warm White)
    0, 0, 0
  },
  {                     // ARILUX_LC11 - Arilux AL-LC11 (ESP8266)
                        // https://www.banggood.com/nl/ARILUX-AL-LC11-Super-Mini-LED-WIFI-APP-Controller-RF-Remote-Control-For-RGBWW-LED-Strip-DC9-28V-p-1085112.html
                        //  (PwmFrequency 540Hz)
    GPI8_KEY1,          // GPIO00 Optional Button
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    GPI8_ARIRFSEL,      // GPIO02 RF receiver control
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    GPI8_PWM2,          // GPIO04 RGB LED Green
    GPI8_PWM1,          // GPIO05 RGB LED Red
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_PWM5,          // GPIO12 RGBCW LED Warm
    GPI8_PWM4,          // GPIO13 RGBW LED Cold
    GPI8_PWM3,          // GPIO14 RGB LED Blue
    GPI8_ARIRFRCV,      // GPIO15 RF receiver input
    0, 0
  },
  {                     // ARILUX_LC06 - Arilux AL-LC06 (ESP8285)
                        // https://www.banggood.com/ARILUX-AL-LC06-LED-WIFI-Smartphone-Controller-Romote-5-Channels-DC12-24V-For-RGBWW-Strip-light-p-1061476.html
    GPI8_KEY1,          // GPIO00 Optional Button
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    GPI8_USER,          // GPIO02 Empty pad
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    GPI8_USER,          // GPIO04 W2 - PWM5
    0,
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_PWM2,          // GPIO12 RGB LED Green
    GPI8_PWM3,          // GPIO13 RGB LED Blue
    GPI8_PWM1,          // GPIO14 RGB LED Red
    GPI8_USER,          // GPIO15 RGBW LED White
    0, 0
  },
  {                     // ZENGGE_ZF_WF017 - Zenggee ZJ-WF017-A (ESP12S))
                        // https://www.ebay.com/p/Smartphone-Android-IOS-WiFi-Music-Controller-for-RGB-5050-3528-LED-Strip-Light/534446632?_trksid=p2047675.l2644
    GPI8_KEY1,          // GPIO00 Optional Button
    0,
    GPI8_USER,          // GPIO02 Empty pad
    0,
    GPI8_USER,          // GPIO04 W2 - PWM5
    0,
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_PWM2,          // GPIO12 RGB LED Green
    GPI8_PWM1,          // GPIO13 RGB LED Red
    GPI8_PWM3,          // GPIO14 RGB LED Blue
    0, 0, 0
  },
  {                     // SONOFF_POW_R2 - Sonoff Pow R2 (ESP8285 - CSE7766)
    GPI8_KEY1,          // GPIO00 Button
    GPI8_CSE7766_TX,    // GPIO01 Serial RXD 4800 baud 8E1 CSE7766 energy sensor
    0,
    GPI8_CSE7766_RX,    // GPIO03 Serial TXD
    0, 0,
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL1,          // GPIO12 Red Led and Relay (0 = Off, 1 = On)
    GPI8_LED1_INV,      // GPIO13 Blue Led (0 = On, 1 = Off) - Link and Power status
    0, 0, 0, 0
  },
  {                     // BLITZWOLF_BWSHP - BlitzWolf BW-SHP2 and BW-SHP6 (ESP8285 - BL0937 or HJL-01 Energy Monitoring)
                        // https://www.banggood.com/BlitzWolf-BW-SHP2-Smart-WIFI-Socket-EU-Plug-220V-16A-Work-with-Amazon-Alexa-Google-Assistant-p-1292899.html
                        // https://www.amazon.de/Steckdose-Homecube-intelligente-Verbrauchsanzeige-funktioniert/dp/B076Q2LKHG/ref=sr_1_fkmr0_1
                        // https://www.amazon.de/Intelligente-Stromverbrauch-Fernsteurung-Schaltbare-Energieklasse/dp/B076WZQS4S/ref=sr_1_1
                        // https://www.aliexpress.com/store/product/BlitzWolf-BW-SHP6-EU-Plug-Metering-Version-WIFI-Smart-Socket-220V-240V-10A-Work-with-Amazon/1965360_32945504669.html
    GPI8_LED1_INV,      // GPIO00 Red Led (1 = On, 0 = Off) - Power status
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    GPI8_LEDLNK_INV,    // GPIO02 Blue Led (1 = On, 0 = Off) - Link status
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    0,
    GPI8_HJL_CF,        // GPIO05 BL0937 or HJL-01 CF power
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_NRG_SEL_INV,   // GPIO12 BL0937 or HJL-01 Sel output (0 = Voltage)
    GPI8_KEY1,          // GPIO13 Button
    GPI8_NRG_CF1,       // GPIO14 BL0937 or HJL-01 CF1 current / voltage
    GPI8_REL1,          // GPIO15 Relay (0 = Off, 1 = On)
    0, 0
  },
  {                     // SHELLY1 - Shelly1 Open Source (ESP8266 - 2MB) - https://shelly.cloud/shelly1-open-source/
    GPI8_USER,          // GPIO00 - Can be changed to GPI8_USER, only if Shelly is powered with 12V DC
    GPI8_USER,          // GPIO01 Serial RXD - Can be changed to GPI8_USER, only if Shelly is powered with 12V DC
    0,
    GPI8_USER,          // GPIO03 Serial TXD - Can be changed to GPI8_USER, only if Shelly is powered with 12V DC
    GPI8_REL1,          // GPIO04 Relay (0 = Off, 1 = On)
    GPI8_SWT1_NP,       // GPIO05 SW pin
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    0, 0, 0, 0, 0, 0
  },
  {                     // SHELLY2 - Shelly2 (ESP8266 - 2MB) - https://shelly.cloud/shelly2/
    0,
    GPI8_MCP39F5_TX,    // GPIO01 MCP39F501 Serial input
    0,
    GPI8_MCP39F5_RX,    // GPIO03 MCP39F501 Serial output
    GPI8_REL1,          // GPIO04
    GPI8_REL2,          // GPIO05
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_SWT1,          // GPIO12
    0,
    GPI8_SWT2,          // GPIO14
    GPI8_MCP39F5_RST,   // GPIO15 MCP39F501 Reset
    0,
    0
  },
  {                     // PHILIPS - Xiaomi Philips bulb (ESP8266)
    0, 0, 0, 0, 0, 0,
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_PWM2,          // GPIO12 cold/warm light
    0, 0,
    GPI8_PWM1,          // GPIO15 light intensity
    0, 0
  },
  {                     // NEO_COOLCAM - Neo Coolcam (ESP8266)
                        // https://www.banggood.com/NEO-COOLCAM-WiFi-Mini-Smart-Plug-APP-Remote-Control-Timing-Smart-Socket-EU-Plug-p-1288562.html?cur_warehouse=CN
    0, 0, 0, 0,
    GPI8_LED1_INV,      // GPIO04 Red Led (0 = On, 1 = Off) - Link and Power status
    0,
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL1,          // GPIO12 Red Led and Relay (0 = Off, 1 = On)
    GPI8_KEY1,          // GPIO13 Button
    0, 0, 0, 0
  },
  {                     // ESP_SWITCH - Michael Haustein 4 channel wall switch (ESP07 = ESP8266)
                        // Use rules for further actions like - rule on power1#state do publish cmnd/other_device/power %value% endon
    GPI8_KEY2,          // GPIO00 Button 2
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    GPI8_REL3_INV,      // GPIO02 Yellow Led 3 (0 = On, 1 = Off)
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    GPI8_KEY1,          // GPIO04 Button 1
    GPI8_REL2_INV,      // GPIO05 Red Led 2 (0 = On, 1 = Off)
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL4_INV,      // GPIO12 Blue Led 4 (0 = On, 1 = Off)
    GPI8_KEY4,          // GPIO13 Button 4
    GPI8_KEY3,          // GPIO14 Button 3
    GPI8_LED1,          // GPIO15 Optional sensor
    GPI8_REL1_INV,      // GPIO16 Green Led 1 (0 = On, 1 = Off)
    0
  },
  {                     // OBI - OBI socket (ESP8266) - https://www.obi.de/hausfunksteuerung/wifi-stecker-schuko/p/2291706
    GPI8_USER,          // GPIO00
    GPI8_USER,          // GPIO01 Serial RXD
    0,
    GPI8_USER,          // GPIO03 Serial TXD
    GPI8_LED1,          // GPIO04 Blue LED - Link and Power status
    GPI8_REL1,          // GPIO05 (Relay OFF, but used as Relay Switch)
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_LED3,          // GPIO12 (Relay ON, but set to LOW, so we can switch with GPIO05)
    GPI8_USER,          // GPIO13
    GPI8_KEY1,          // GPIO14 Button
    0,
    GPI8_USER,          // GPIO16
    GPI8_USER           // ADC0   A0 Analog input
  },
  {                     // TECKIN - https://www.amazon.de/gp/product/B07D5V139R
    0,
    GPI8_KEY1,          // GPIO01 Serial TXD and Button
    0,
    GPI8_LED1_INV,      // GPIO03 Serial RXD and Red Led (0 = On, 1 = Off) - Power status
    GPI8_HJL_CF,        // GPIO04 BL0937 or HJL-01 CF power
    GPI8_NRG_CF1,       // GPIO05 BL0937 or HJL-01 CF1 current / voltage
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_NRG_SEL_INV,   // GPIO12 BL0937 or HJL-01 Sel output (0 = Voltage)
    GPI8_LEDLNK_INV,    // GPIO13 Blue Led (0 = On, 1 = Off) - Link status
    GPI8_REL1,          // GPIO14 Relay (0 = Off, 1 = On)
    0, 0, 0
  },
  {                     // APLIC_WDP303075 - Aplic WDP 303075 (ESP8285 - HLW8012 Energy Monitoring)
                        // https://www.amazon.de/dp/B07CNWVNJ2
    0, 0, 0,
    GPI8_KEY1,          // GPIO03 Button
    GPI8_HLW_CF,        // GPIO04 HLW8012 CF power
    GPI8_NRG_CF1,       // GPIO05 HLW8012 CF1 current / voltage
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_NRG_SEL_INV,   // GPIO12 HLW8012 CF Sel output (0 = Voltage)
    GPI8_LED1_INV,      // GPIO13 LED (0 = On, 1 = Off) - Link and Power status
    GPI8_REL1,          // GPIO14 Relay SRU 5VDC SDA (0 = Off, 1 = On )
    0, 0, 0
  },
  {                     // TUYA_DIMMER - Tuya MCU device (ESP8266 w/ separate MCU)
                        // https://www.amazon.com/gp/product/B07CTNSZZ8/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
    GPI8_USER,          // Virtual Button (controlled by MCU)
    GPI8_USER,          // GPIO01 MCU serial control
    GPI8_USER,
    GPI8_USER,          // GPIO03 MCU serial control
    GPI8_USER,
    GPI8_USER,
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_USER,
    GPI8_USER,
    GPI8_USER,          // GPIO14 Green Led
    GPI8_USER,
    GPI8_USER,
    0
  },
  {                     // GOSUND - https://www.amazon.de/gp/product/B0777BWS1P
    0,
    GPI8_LEDLNK_INV,    // GPIO01 Serial RXD and LED1 (blue) inv - Link status
    0,
    GPI8_KEY1,          // GPIO03 Serial TXD and Button
    GPI8_HJL_CF,        // GPIO04 BL0937 or HJL-01 CF power
    GPI8_NRG_CF1,       // GPIO05 BL0937 or HJL-01 CF1 current / voltage
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_NRG_SEL_INV,   // GPIO12 BL0937 or HJL-01 Sel output (0 = Voltage)
    GPI8_LED1_INV,      // GPIO13 LED2 (red) inv - Power status
    GPI8_REL1,          // GPIO14 Relay (0 = Off, 1 = On)
    0, 0, 0
  },
  {                     // ARMTRONIX_DIMMERS - ARMTRONIX Dimmer, one or two channel (ESP8266 w/ separate MCU dimmer)
                        // https://www.tindie.com/products/Armtronix/wifi-ac-dimmer-two-triac-board/
                        // https://www.tindie.com/products/Armtronix/wifi-ac-dimmer-esp8266-one-triac-board-alexaecho/
    GPI8_USER,
    GPI8_TXD,           // GPIO01 MCU serial control
    GPI8_USER,
    GPI8_RXD,           // GPIO03 MCU serial control
    GPI8_USER,
    GPI8_USER,
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_USER,
    GPI8_USER,
    GPI8_USER,
    GPI8_USER,
    GPI8_USER,
    0
  },
  {                     // SK03_TUYA - Outdoor smart plug with power monitoring HLW8012 chip - https://www.amazon.com/gp/product/B07CG7MBPV
    GPI8_KEY1,          // GPIO00 Button
    0, 0, 0,
    GPI8_HLW_CF,        // GPIO04 HLW8012 CF power
    GPI8_NRG_CF1,       // GPIO05 HLW8012 CF1 current / voltage
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_NRG_SEL_INV,   // GPIO12 HLW8012 CF Sel output (0 = Voltage)
    GPI8_LED1_INV,      // GPIO13 Red Led (0 = On, 1 = Off) - Power status
    GPI8_LEDLNK_INV,    // GPIO14 Blue Led (0 = On, 1 = Off) - Link status
    GPI8_REL1,          // GPIO15 Relay (0 = Off, 1 = On)
    0, 0
  },
  {                     // PS_16_DZ - PS-16-DZ Dimmer (ESP8266 w/ separate Nuvoton MCU dimmer)
                        // https://www.aliexpress.com/item/SM-Smart-WIFI-Wall-Dimmer-Light-Switch-US-Ewelink-APP-Remote-Control-Wi-Fi-Wirele-Work/32871151902.html
    GPI8_USER,
    GPI8_TXD,           // GPIO01 MCU serial control
    GPI8_USER,
    GPI8_RXD,           // GPIO03 MCU serial control
    GPI8_USER,
    GPI8_USER,
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_USER,
    GPI8_LED1,          // GPIO13 WiFi LED - Link and Power status
    GPI8_USER,
    GPI8_USER,
    GPI8_USER,
    0
  },
  {                     // TECKIN_US - Teckin SP20 US with Energy Monitoring
                        // https://www.amazon.com/Outlet-Compatible-Monitoring-Function-Required/dp/B079Q5W22B
                        // https://www.amazon.com/Outlet-ZOOZEE-Monitoring-Function-Compatible/dp/B07J2LR5KN
    GPI8_LED1_INV,      // GPIO00 Red Led (1 = On, 0 = Off) - Power status
    0,
    GPI8_LEDLNK_INV,    // GPIO02 Blue Led (1 = On, 0 = Off) - Link status
    0,
    GPI8_REL1,          // GPIO04 Relay (0 = Off, 1 = On)
    GPI8_HJL_CF,        // GPIO05 BL0937 or HJL-01 CF power
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_NRG_SEL_INV,   // GPIO12 BL0937 or HJL-01 Sel output (0 = Voltage)
    GPI8_KEY1,          // GPIO13 Button
    GPI8_NRG_CF1,       // GPIO14 BL0937 or HJL-01 CF1 current / voltage
    0, 0, 0
  },
  {                     // MANZOKU_EU_4 - "MANZOKU" labeled power strip, EU version
                        // https://www.amazon.de/Steckdosenleiste-AOFO-Mehrfachsteckdose-Ãœberspannungsschutz-Sprachsteuerung/dp/B07GBSD11P/
                        // https://www.amazon.de/Steckdosenleiste-Geekbes-USB-Anschluss-Kompatibel-gesteuert/dp/B078W23BW9/
    0,                  // GPIO00
    0,                  // GPIO01 Serial RXD
    0,
    GPI8_KEY1,          // GPIO03 Serial TXD + Button
    GPI8_REL2,          // GPIO04 Relay 2
    GPI8_REL1,          // GPIO05 Relay 1
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL3,          // GPIO12 Relay 3
    GPI8_REL4,          // GPIO13 Relay 4
    GPI8_USER,          // GPIO14
    0,
    GPI8_USER,          // GPIO16
    0
  },
  {                     // OBI2 - OBI socket (ESP8266) - https://www.obi.de/hausfunksteuerung/wifi-stecker-schuko-2-stueck-weiss/p/4077673
    0,                  // GPIO00
    0,                  // GPIO01 Serial RXD
    0,
    0,                  // GPIO03 Serial TXD
    GPI8_REL1,          // GPIO04 Relay 1
    GPI8_KEY1,          // GPIO05 Button
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_LEDLNK_INV,    // GPIO12 Green LED - Link status
    GPI8_LED1,          // GPIO13 Red LED - Power status
    0, 0, 0, 0
  },
  {                     // YTF_IR_BRIDGE - https://www.aliexpress.com/item/Tuya-universal-Smart-IR-Hub-remote-control-Voice-Control-AC-TV-Work-With-Alexa-Google-Home/32951202513.html
    GPI8_USER,          // GPIO00
    GPI8_USER,          // GPIO01 Serial RXD
    GPI8_USER,          // GPIO02
    GPI8_USER,          // GPIO03 Serial TXD
    GPI8_LED1_INV,      // GPIO04 Blue Led - Link status
    GPI8_IRRECV,        // GPIO05 IR Receiver
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    0,                  // GPIO12
    GPI8_KEY1,          // GPIO13 Button
    GPI8_IRSEND,        // GPIO14 IR Transmitter
    0, 0, 0
  },
  {                     // DIGOO - Digoo DG-SP202
                        // https://www.banggood.com/DIGOO-DG-SP202-Dual-EU-Plug-Smart-WIFI-Socket-Individual-Controllable-Energy-Monitor-Remote-Control-Timing-Smart-Home-Outlet-let-p-1375323.html
    GPI8_KEY1,          // GPIO00 Button1
    0,                  // GPIO01 Serial RXD
    0,                  // GPIO02
    0,                  // GPIO03 Serial TXD
    GPI8_HJL_CF,        // GPIO04 BL0937 or HJL-01 CF power
    GPI8_NRG_CF1,       // GPIO05 BL0937 or HJL-01 CF1 current / voltage
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_NRG_SEL_INV,   // GPIO12 BL0937 or HJL-01 Sel output (0 = Voltage)
    GPI8_LED1,          // GPIO13 Blue Leds - Link Status
    GPI8_REL2,          // GPIO14 Relay2 (0 = Off, 1 = On) and Red Led
    GPI8_REL1,          // GPIO15 Relay1 (0 = Off, 1 = On) and Red Led
    GPI8_KEY2_NP,       // GPIO16 Button2, externally pulled up
    0
  },
  {                     // KA10 - SMANERGY KA10 (ESP8285 - BL0937 Energy Monitoring) - https://www.amazon.es/dp/B07MBTCH2Y
    0,                  // GPIO00
    GPI8_LEDLNK_INV,    // GPIO01 Blue LED - Link status
    0,                  // GPIO02
    GPI8_KEY1,          // GPIO03 Button
    GPI8_HJL_CF,        // GPIO04 BL0937 CF power
    GPI8_NRG_CF1,       // GPIO05 BL0937 CF1 voltage / current
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_NRG_SEL_INV,   // GPIO12 BL0937 Sel output (1 = Voltage)
    GPI8_LED1,          // GPIO13 Red LED - Power status
    GPI8_REL1,          // GPIO14 Relay 1
    0, 0, 0
  },
  {                     // ZX2820
    GPI8_KEY1,          // GPIO00 Button
    0, 0, 0,
    GPI8_HLW_CF,        // GPIO04 HLW8012 CF power
    GPI8_NRG_CF1,       // GPIO05 HLW8012 CF1 voltage / current
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_NRG_SEL_INV,   // GPIO12 HLW8012 SEL (0 = Voltage)
    GPI8_LED1_INV,      // GPIO13 Green Led - Link and Power status
    GPI8_REL1,          // GPIO14 Relay
    0, 0, 0
  },
  {                     // MI_DESK_LAMP - Mi LED Desk Lamp - https://www.mi.com/global/smartlamp/
    0, 0,
    GPI8_KEY1,          // GPIO02 Button
    0,
    GPI8_PWM1,          // GPIO04 Cold White
    GPI8_PWM2,          // GPIO05 Warm White
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_ROT1A,         // GPIO12 Rotary switch A pin
    GPI8_ROT1B,         // GPIO13 Rotary switch B pin
    0, 0, 0, 0
  },
  {                     // SP10 - Tuya SP10 (BL0937 Energy Monitoring)
                        // https://www.aliexpress.com/item/Smart-Mini-WiFi-Plug-Outlet-Switch-Work-With-ForEcho-Alexa-Google-Home-Remote-EU-Smart-Socket/32963670423.html
    0,                  // GPIO00
    GPI8_PWM1,          // GPIO01 Nightlight
    0,                  // GPIO02
    GPI8_KEY1,          // GPIO03 Button
    GPI8_HJL_CF,        // GPIO04 BL0937 CF power
    GPI8_NRG_CF1,       // GPIO05 BL0937 CF1 voltage / current
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_NRG_SEL_INV,   // GPIO12 BL0937 Sel output (1 = Voltage)
    GPI8_LED1,          // GPIO13 Blue LED - Link status
    GPI8_REL1,          // GPIO14 Relay and red LED
    0, 0, 0
  },
  {                     // WAGA - WAGA life CHCZ02MB (HJL-01 Energy Monitoring)
                        // https://www.ebay.com/itm/332595697006
    GPI8_LED1_INV,      // GPIO00 Red LED
    0,                  // GPIO01 Serial RXD
    0,                  // GPIO02
    GPI8_NRG_SEL_INV,   // GPIO03 HJL-01 Sel output (1 = Voltage)
    0,                  // GPIO04
    GPI8_HJL_CF,        // GPIO05 HJL-01 CF power
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL1,          // GPIO12 Relay
    GPI8_KEY1,          // GPIO13 Button
    GPI8_NRG_CF1,       // GPIO14 HJL-01 CF1 voltage / current
    GPI8_LEDLNK_INV,    // GPIO15 Blue LED - Link status
    0, 0
  },
  {                     // SYF05 - Sunyesmart SYF05 (a.k.a. Fcmila) = TYWE3S + SM16726
                        // Also works with Merkury 904 RGBW Bulbs with 13 set to GPI8_SM16716_SEL
                        // https://www.flipkart.com/fc-mila-bxav-xs-ad-smart-bulb/p/itmf85zgs45fzr7n
                        // https://docs.tuya.com/en/hardware/WiFi-module/wifi-e3s-module.html
                        // http://www.datasheet-pdf.com/PDF/SM16716-Datasheet-Sunmoon-932771
    GPI8_USER,          // GPIO00 N.C.
    0,                  // GPIO01 Serial RXD
    GPI8_USER,          // GPIO02 N.C.
    0,                  // GPIO03 Serial TXD
    GPI8_SM16716_CLK,   // GPIO04 SM16716 Clock
    GPI8_PWM1,          // GPIO05 White
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_USER,          // GPIO12 Alt. White on some devices
    GPI8_USER,          // GPIO13 SM16716 Enable on some devices
    GPI8_SM16716_DAT,   // GPIO14 SM16716 Data
    0,                  // GPIO15 wired to GND
    GPI8_USER,          // GPIO16 N.C.
    GPI8_USER           // ADC0 A0 Analog input
  },
  {                     // EXS_DIMMER - EX-Store WiFi Dimmer v4, two channel (ESP8266 w/ separate MCU dimmer)
                        // https://ex-store.de/2-Kanal-RS232-WiFi-WLan-Dimmer-Modul-V4-fuer-Unterputzmontage-230V-3A
                        // https://ex-store.de/2-Kanal-RS232-WiFi-WLan-Dimmer-Modul-V4-fuer-Unterputzmontage-230V-3A-ESP8266-V12-Stift-und-Buchsenleisten
    0,
    GPI8_TXD,           // GPIO01 MCU serial control
    GPI8_LEDLNK,        // GPIO02 LED Link
    GPI8_RXD,           // GPIO03 MCU serial control
    GPI8_USER,          // GPIO04
    GPI8_USER,          // GPIO05
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_USER,          // GPIO12
    GPI8_EXS_ENABLE,    // GPIO13 EXS MCU Enable
    GPI8_USER,          // GPIO14
    0,                  // GPIO15
    0, 0
  },
  {                     // PWM_DIMMER - Support for Martin Jerry/acenx/Tessan/NTONPOWER SD0x PWM
                        // dimmer switches. The brightness of the load for these dimmers is
                        // controlled by a PWM GPIO pin. There are typically power, up & down
                        // buttons and 4 LED's. Examples are:
                        // https://www.amazon.com/dp/B07FXYSVR1
                        // https://www.amazon.com/dp/B07V26Q3VD
                        // https://www.amazon.com/dp/B07K67D43J
                        // https://www.amazon.com/dp/B07TTGFWFM
    GPI8_KEY3,          // GPIO00 Up button
    GPI8_KEY2,          // GPIO01 Down button
    0,                  // GPIO02
    GPI8_LED4_INV,      // GPIO03 Level 5 LED
    GPI8_LEDLNK_INV,    // GPIO04 LED Link
    GPI8_LED3_INV,      // GPIO05 Level 4 LED
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_LED2_INV,      // GPIO12 Level 3 LED
    GPI8_PWM1,          // GPIO13 Dimmer PWM
    GPI8_LED1_INV,      // GPIO12 Level 2 LED
    GPI8_KEY1_INV,      // GPIO15 Power button
    GPI8_REL1_INV,      // GPIO16 Power relay/Level 1 LED
    0
  },
  {                     // SONOFF_ZB_BRIDGE - Sonoff Zigbee Bridge (ESP8266)
    GPI8_LED1_INV,      // GPIO00 Green Led (0 = On, 1 = Off) - Traffic between ESP and EFR
    GPI8_ZIGBEE_TX,     // GPIO01 Zigbee Serial control
    0,                  // GPIO02
    GPI8_ZIGBEE_RX,     // GPIO03 Zigbee Serial control
    GPI8_ZIGBEE_RST,    // GPIO04 Zigbee Reset
    0,                  // GPIO05 EFR32 Bootloader mode (drive Low for Gecko Bootloader, inactive or high for Zigbee EmberZNet)
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
                        // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
                        // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_I2C_SDA,       // GPIO12 I2C SDA - connected to 512KB EEPROM
    GPI8_LEDLNK_INV,    // GPIO13 Blue Led (0 = On, 1 = Off) - Link status
    GPI8_I2C_SCL,       // GPIO14 I2C SCL - connected to 512KB EEPROM
    0,                  // GPIO15 connected to IO15 pad, also used for logging
    GPI8_KEY1,          // GPIO16 Button
    0
  }
};

/*********************************************************************************************\
 * Templates with 14 usable pins (ESP8285)
\*********************************************************************************************/

const mytmplt8285 kModules8285[TMP_MAXMODULE_8266 - TMP_WEMOS] PROGMEM = {
  {                     // WEMOS - Any ESP8266/ESP8285 device like WeMos and NodeMCU hardware (ESP8266)
    GPI8_USER,          // GPIO00 D3 Wemos Button Shield
    GPI8_USER,          // GPIO01 TX Serial RXD
    GPI8_USER,          // GPIO02 D4 Wemos DHT Shield
    GPI8_USER,          // GPIO03 RX Serial TXD and Optional sensor
    GPI8_USER,          // GPIO04 D2 Wemos I2C SDA
    GPI8_USER,          // GPIO05 D1 Wemos I2C SCL / Wemos Relay Shield (0 = Off, 1 = On) / Wemos WS2812B RGB led Shield
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
    GPI8_USER,          // GPIO09 (SD_DATA2 Flash QIO or ESP8285)
    GPI8_USER,          // GPIO10 (SD_DATA3 Flash QIO or ESP8285)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_USER,          // GPIO12 D6
    GPI8_USER,          // GPIO13 D7
    GPI8_USER,          // GPIO14 D5
    GPI8_USER,          // GPIO15 D8
    GPI8_USER,          // GPIO16 D0 Wemos Wake
    GPI8_USER           // ADC0 A0 Analog input
  },
  {                     // SONOFF_4CH - Sonoff 4CH (ESP8285)
    GPI8_KEY1,          // GPIO00 Button 1
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    GPI8_USER,          // GPIO02 Optional sensor
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    GPI8_REL3,          // GPIO04 Sonoff 4CH Red Led and Relay 3 (0 = Off, 1 = On)
    GPI8_REL2,          // GPIO05 Sonoff 4CH Red Led and Relay 2 (0 = Off, 1 = On)
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
    GPI8_KEY2,          // GPIO09 Button 2
    GPI8_KEY3,          // GPIO10 Button 3
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL1,          // GPIO12 Red Led and Relay 1 (0 = Off, 1 = On) - Link and Power status
    GPI8_LED1_INV,      // GPIO13 Blue Led (0 = On, 1 = Off)
    GPI8_KEY4,          // GPIO14 Button 4
    GPI8_REL4,          // GPIO15 Red Led and Relay 4 (0 = Off, 1 = On)
    0, 0
  },
  {                     // SONOFF_T12 - Sonoff T1 2CH (ESP8285)
    GPI8_KEY1,          // GPIO00 Button 1
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    GPI8_USER,          // GPIO02 Optional Sensor (J3 Pin 5)
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    0,
    GPI8_REL2,          // GPIO05 Blue Led and Relay 2 (0 = Off, 1 = On)
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
    GPI8_KEY2,          // GPIO09 Button 2
    0,                  // GPIO10
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL1,          // GPIO12 Blue Led and Relay 1 (0 = Off, 1 = On)
    GPI8_LED1_INV,      // GPIO13 Blue Led (0 = On, 1 = Off) - Link and Power status
    0, 0, 0, 0
  },
  {                     // SONOFF_T13 - Sonoff T1 3CH (ESP8285)
    GPI8_KEY1,          // GPIO00 Button 1
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    GPI8_USER,          // GPIO02 Optional Sensor (J3 Pin 5)
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    GPI8_REL3,          // GPIO04 Blue Led and Relay 3 (0 = Off, 1 = On)
    GPI8_REL2,          // GPIO05 Blue Led and Relay 2 (0 = Off, 1 = On)
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
    GPI8_KEY2,          // GPIO09 Button 2
    GPI8_KEY3,          // GPIO10 Button 3
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL1,          // GPIO12 Blue Led and Relay 1 (0 = Off, 1 = On)
    GPI8_LED1_INV,      // GPIO13 Blue Led (0 = On, 1 = Off) - Link and Power status
    0, 0, 0, 0
  },
  {                     // SONOFF_DUAL_R2 - Sonoff Dual R2 (ESP8285)
    GPI8_USER,          // GPIO00 Button 0 on header (0 = On, 1 = Off)
    GPI8_USER,          // GPIO01 Serial RXD and Optional sensor
    0,
    GPI8_USER,          // GPIO03 Serial TXD and Optional sensor
    0,
    GPI8_REL2,          // GPIO05 Relay 2 (0 = Off, 1 = On)
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
    GPI8_USER,          // GPIO09 Button 1 on header (0 = On, 1 = Off)
    GPI8_KEY1,          // GPIO10 Button on casing
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL1,          // GPIO12 Relay 1 (0 = Off, 1 = On)
    GPI8_LED1_INV,      // GPIO13 Blue Led (0 = On, 1 = Off) - Link and Power status
    0, 0, 0, 0
  },
  {                     // SONOFF_IFAN03 - Sonoff iFan03 (ESP8285)
    GPI8_KEY1,          // GPIO00 WIFI_KEY0 Button 1
    GPI8_TXD,           // GPIO01 ESP_TXD Serial RXD connection to P0.5 of RF microcontroller
    0,                  // GPIO02 ESP_LOG
    GPI8_RXD,           // GPIO03 ESP_RXD Serial TXD connection to P0.4 of RF microcontroller
    0,                  // GPIO04 DEBUG_RX
    0,                  // GPIO05 DEBUG_TX
                        // GPIO06 (SD_CLK   Flash)
                        // GPIO07 (SD_DATA0 Flash QIO/DIO/DOUT)
                        // GPIO08 (SD_DATA1 Flash QIO/DIO/DOUT)
    GPI8_REL1_INV,      // GPIO09 WIFI_O0 Relay 1 (0 = Off, 1 = On) controlling the light
    GPI8_BUZZER_INV,    // GPIO10 WIFI_O4 Buzzer (0 = Off, 1 = On)
                        // GPIO11 (SD_CMD   Flash)
    GPI8_REL3,          // GPIO12 WIFI_O2 Relay 3 (0 = Off, 1 = On) controlling the fan
    GPI8_LED1_INV,      // GPIO13 WIFI_CHK Blue Led on PCA (0 = On, 1 = Off) - Link and Power status
    GPI8_REL2,          // GPIO14 WIFI_O1 Relay 2 (0 = Off, 1 = On) controlling the fan
    GPI8_REL4,          // GPIO15 WIFI_O3 Relay 4 (0 = Off, 1 = On) controlling the fan
    0, 0
  }
};

#endif  // ESP8266

#ifdef ESP32
#if CONFIG_IDF_TARGET_ESP32C2
/********************************************************************************************\
 * ESP32-C2 Module templates
\********************************************************************************************/

#define USER_MODULE        255

// Supported hardware modules
enum SupportedModulesESP32C2 {
  WEMOS, // not really correct, a placeholder for now
  MAXMODULE };

// Default module settings
const uint8_t kModuleNiceList[] PROGMEM = {
  WEMOS,
};

// !!! Update this list in the same order as kModuleNiceList !!!
const char kModuleNames[] PROGMEM =
  "ESP32C2|"
  ;

// !!! Update this list in the same order as SupportedModulesESP32C2 !!!
const mytmplt kModules[] PROGMEM = {
  {                              // Generic ESP32C2 device
    AGPIO(GPIO_USER),            // 0       IO                  GPIO0, ADC1_CH0,  RTC
    AGPIO(GPIO_USER),            // 1       IO                  GPIO1, ADC1_CH1,  RTC
    AGPIO(GPIO_USER),            // 2       IO                  GPIO2, ADC1_CH2,  RTC
    AGPIO(GPIO_USER),            // 3       IO                  GPIO3, ADC1_CH3,  RTC 
    AGPIO(GPIO_USER),            // 4       IO                  GPIO4, ADC1_CH4,  RTC 
    AGPIO(GPIO_USER),            // 5       IO                  GPIO5, RTC 
    AGPIO(GPIO_USER),            // 6       IO                  GPIO6,
    AGPIO(GPIO_USER),            // 7       IO                  GPIO7, 
    AGPIO(GPIO_USER),            // 8       IO                  GPIO8, Strapping
    AGPIO(GPIO_USER),            // 9       IO                  GPIO9, Strapping
    AGPIO(GPIO_USER),            // 10      IO                  GPIO10
    0,                           // 11      IO                  GPIO11, output power supply for flash
    0,                           // 12      IO                  GPIO12, SPIHD - Free if flash DIO/DOUT
    0,                           // 13      IO                  GPIO13, SPIWP - Free if flash DIO/DOUT
    0,                           // 14      IO                  GPIO14, SPICS0
    0,                           // 15      IO                  GPIO15, SPICLK
    0,                           // 16      IO                  GPIO16, SPID
    0,                           // 17      IO                  GPIO17, SPIQ
    AGPIO(GPIO_USER),            // 18      IO                  GPIO18,
    AGPIO(GPIO_USER),            // 19      IO     RXD0         GPIO19, U0RXD
    AGPIO(GPIO_USER),            // 20      IO     TXD0         GPIO20, U0TXD
    0                            // Flag
  },
};

/*********************************************************************************************\
 Known templates
\*********************************************************************************************/

#elif CONFIG_IDF_TARGET_ESP32C3
/********************************************************************************************\
 * ESP32-C3 Module templates
\********************************************************************************************/

#define USER_MODULE        255

// Supported hardware modules
enum SupportedModulesESP32C3 {
  WEMOS,
  MAXMODULE };

// Default module settings
const uint8_t kModuleNiceList[] PROGMEM = {
  WEMOS,
};

// !!! Update this list in the same order as kModuleNiceList !!!
const char kModuleNames[] PROGMEM =
  "ESP32C3|"
  ;

// !!! Update this list in the same order as SupportedModulesESP32C3 !!!
const mytmplt kModules[] PROGMEM = {
  {                              // Generic ESP32C3 device
    AGPIO(GPIO_USER),            // 0       IO                  GPIO0, ADC1_CH0, XTAL_32K_P
    AGPIO(GPIO_USER),            // 1       IO                  GPIO1, ADC1_CH1, XTAL_32K_N
    AGPIO(GPIO_USER),            // 2       IO                  GPIO2, ADC1_CH2, FSPIQ
    AGPIO(GPIO_USER),            // 3       IO                  GPIO3, ADC1_CH3
    AGPIO(GPIO_USER),            // 4       IO                  GPIO4, ADC1_CH4, FSPIHD, MTMS
    AGPIO(GPIO_USER),            // 5       IO                  GPIO5, ADC2_CH0, FSPIWP, MTDI
    AGPIO(GPIO_USER),            // 6       IO                  GPIO6, FSPICLK, MTCK
    AGPIO(GPIO_USER),            // 7       IO                  GPIO7, FSPID, MTDO
    AGPIO(GPIO_USER),            // 8       IO                  GPIO8
    AGPIO(GPIO_USER),            // 9       IO                  GPIO9
    AGPIO(GPIO_USER),            // 10      IO                  GPIO10
    0,                           // 11      IO                  GPIO11, output power supply for flash
    0,                           // 12      IO                  GPIO12, SPIHD - Free if flash DIO/DOUT
    0,                           // 13      IO                  GPIO13, SPIWP - Free if flash DIO/DOUT
    0,                           // 14      IO                  GPIO14, SPICS0
    0,                           // 15      IO                  GPIO15, SPICLK
    0,                           // 16      IO                  GPIO16, SPID
    0,                           // 17      IO                  GPIO17, SPIQ
    AGPIO(GPIO_USER),            // 18      IO                  GPIO18, USB_D
    AGPIO(GPIO_USER),            // 19      IO                  GPIO19, USB_D+
    AGPIO(GPIO_USER),            // 20      IO     RXD0         GPIO20, U0RXD
    AGPIO(GPIO_USER),            // 21      IO     TXD0         GPIO21, U0TXD
    0                            // Flag
  },
};

/*********************************************************************************************\
 Known templates
\*********************************************************************************************/

#elif CONFIG_IDF_TARGET_ESP32C6
/********************************************************************************************\
 * ESP32-C6 Module templates
\********************************************************************************************/

#define USER_MODULE        255

// Supported hardware modules
enum SupportedModulesESP32C6 {
  WEMOS, // not really correct, a placeholder for now
  MAXMODULE };

// Default module settings
const uint8_t kModuleNiceList[] PROGMEM = {
  WEMOS,
};

// !!! Update this list in the same order as kModuleNiceList !!!
const char kModuleNames[] PROGMEM =
  "ESP32C6|"
  ;

// !!! Update this list in the same order as SupportedModulesESP32C6 !!!
const mytmplt kModules[] PROGMEM = {
  {                              // Generic ESP32C6 device
    AGPIO(GPIO_USER),            // 0       IO                  GPIO0, ADC1_CH0, LP_GPIO0
    AGPIO(GPIO_USER),            // 1       IO                  GPIO1, ADC1_CH1, LP_GPIO1
    AGPIO(GPIO_USER),            // 2       IO                  GPIO2, ADC1_CH2, LP_GPIO2
    AGPIO(GPIO_USER),            // 3       IO                  GPIO3, ADC1_CH3, LP_GPIO3 
    AGPIO(GPIO_USER),            // 4       IO                  GPIO4, ADC1_CH4, LP_GPIO4, Strapping
    AGPIO(GPIO_USER),            // 5       IO                  GPIO5, ADC1_CH5, LP_GPIO5, Strapping
    AGPIO(GPIO_USER),            // 6       IO                  GPIO6, ADC1_CH6, LP_GPIO6
    AGPIO(GPIO_USER),            // 7       IO                  GPIO7,           LP_GPIO7
    AGPIO(GPIO_USER),            // 8       IO                  GPIO8, Strapping
    AGPIO(GPIO_USER),            // 9       IO                  GPIO9, Strapping
    AGPIO(GPIO_USER),            // 10      IO                  GPIO10 (QFN40 only)
    AGPIO(GPIO_USER),            // 11      IO                  GPIO11 (QFN40 only)
    AGPIO(GPIO_USER),            // 12      IO                  GPIO12, USB-JTAG
    AGPIO(GPIO_USER),            // 13      IO                  GPIO13, USB-JTAG
    AGPIO(GPIO_USER),            // 14      IO                  GPIO14 (QFN32 only)
    AGPIO(GPIO_USER),            // 15      IO                  GPIO15, Strapping
    AGPIO(GPIO_USER),            // 16      IO     TXD0         GPIO16, U0TXD
    AGPIO(GPIO_USER),            // 17      IO     RXD0         GPIO17, U0RXD
    AGPIO(GPIO_USER),            // 18      IO                  GPIO18, SDIO_CMD
    AGPIO(GPIO_USER),            // 19      IO                  GPIO19, SDIO_CLK
    AGPIO(GPIO_USER),            // 20      IO                  GPIO20, SDIO_DATA0
    AGPIO(GPIO_USER),            // 21      IO                  GPIO21, SDIO_DATA1
    AGPIO(GPIO_USER),            // 22      IO                  GPIO22, SDIO_DATA2
    AGPIO(GPIO_USER),            // 23      IO                  GPIO23, SDIO_DATA3
    0,                           // 24      IO                  GPIO24, SPICS1, PSRAM
    0,                           // 25      IO                  GPIO25, SPIQ
    0,                           // 26      IO                  GPIO26, SPIWP - Free if flash DIO/DOUT
    0,                           // 27      IO                  GPIO27, SPIVDD
    0,                           // 28      IO                  GPIO28, SPIHD - Free if flash DIO/DOUT
    0,                           // 29      IO                  GPIO29, SPICLK
    0,                           // 30      IO                  GPIO30, SPID
    0                            // Flag
  },
};

/*********************************************************************************************\
 Known templates
\*********************************************************************************************/

#elif CONFIG_IDF_TARGET_ESP32S2
/********************************************************************************************\
 * ESP32-S2 Module templates
\********************************************************************************************/

#define USER_MODULE        255

// Supported hardware modules
enum SupportedModulesESP32S2 {
  WEMOS,
  MAXMODULE };

// Default module settings
const uint8_t kModuleNiceList[] PROGMEM = {
  WEMOS,
};

// !!! Update this list in the same order as kModuleNiceList !!!
const char kModuleNames[] PROGMEM =
  "ESP32S2|"
  ;

// !!! Update this list in the same order as SupportedModulesESP32S2 !!!
const mytmplt kModules[] PROGMEM = {
  {                              // Generic ESP32C3 device
    AGPIO(GPIO_USER),            // 0       IO                  GPIO0, RTC_GPIO0, Strapping
    AGPIO(GPIO_USER),            // 1       AO                  GPIO1, ADC1_CH0, RTC_GPIO1
    AGPIO(GPIO_USER),            // 2       AO                  GPIO2, ADC1_CH1, RTC_GPIO2
    AGPIO(GPIO_USER),            // 3       AO                  GPIO3, ADC1_CH2, RTC_GPIO3
    AGPIO(GPIO_USER),            // 4       AO                  GPIO4, ADC1_CH3, RTC_GPIO4
    AGPIO(GPIO_USER),            // 5       AO                  GPIO5, ADC1_CH4, RTC_GPIO5
    AGPIO(GPIO_USER),            // 6       AO                  GPIO6, ADC1_CH5, RTC_GPIO6
    AGPIO(GPIO_USER),            // 7       AO                  GPIO7, ADC1_CH6, RTC_GPIO7
    AGPIO(GPIO_USER),            // 8       AO                  GPIO8, ADC1_CH7, RTC_GPIO8
    AGPIO(GPIO_USER),            // 9       AO                  GPIO9, ADC1_CH8, RTC_GPIO9
    AGPIO(GPIO_USER),            // 10      AO                  GPIO10, ADC1_CH9, RTC_GPIO10
    AGPIO(GPIO_USER),            // 11      AO                  GPIO11, ADC2_CH0, RTC_GPIO11
    AGPIO(GPIO_USER),            // 12      AO                  GPIO12, ADC2_CH1, RTC_GPIO12
    AGPIO(GPIO_USER),            // 13      AO                  GPIO13, ADC2_CH2, RTC_GPIO13
    AGPIO(GPIO_USER),            // 14      AO                  GPIO14, ADC2_CH3, RTC_GPIO14
    AGPIO(GPIO_USER),            // 15      AO                  GPIO15, ADC2_CH4, RTC_GPIO15, XTAL_32K_P
    AGPIO(GPIO_USER),            // 16      AO                  GPIO16, ADC2_CH5, RTC_GPIO16, XTAL_32K_N
    AGPIO(GPIO_USER),            // 17      AO                  GPIO17, ADC2_CH6, RTC_GPIO17, DAC_1
    AGPIO(GPIO_USER),            // 18      AO                  GPIO18, ADC2_CH7, RTC_GPIO18, DAC_2
    AGPIO(GPIO_USER),            // 19      AO                  GPIO19, ADC2_CH8, RTC_GPIO19
    AGPIO(GPIO_USER),            // 20      AO                  GPIO20, ADC2_CH9, RTC_GPIO20
    AGPIO(GPIO_USER),            // 21      IO                  GPIO21, RTC_GPIO21
                                 // 22      --                  Unused
                                 // 23      --                  Unused
                                 // 24      --                  Unused
                                 // 25      --                  Unused
                                 // 26      FL                  SPICS1, PSRAM
                                 // 27      FL                  SPIHD
                                 // 28      FL                  SPIWP
                                 // 29      FL                  SPICS0
                                 // 30      FL                  SPICLK
                                 // 31      FL                  SPIQ
                                 // 32      FL                  SPID
    AGPIO(GPIO_USER),            // 33      IO                  GPIO33
    AGPIO(GPIO_USER),            // 34      IO                  GPIO34
    AGPIO(GPIO_USER),            // 35      IO                  GPIO35
    AGPIO(GPIO_USER),            // 36      IO                  GPIO36
    AGPIO(GPIO_USER),            // 37      IO                  GPIO37
    AGPIO(GPIO_USER),            // 38      IO                  GPIO38
    AGPIO(GPIO_USER),            // 39      IO                  GPIO39, JTAG MTCK
    AGPIO(GPIO_USER),            // 40      IO                  GPIO40, JTAG MTDO
    AGPIO(GPIO_USER),            // 41      IO                  GPIO41, JTAG MTDI
    AGPIO(GPIO_USER),            // 42      IO                  GPIO42, JTAG MTMS
    AGPIO(GPIO_USER),            // 43      IO                  GPIO43, U0TXD
    AGPIO(GPIO_USER),            // 44      IO                  GPIO44, U0RXD
    AGPIO(GPIO_USER),            // 45      IO                  GPIO45, Strapping
    AGPIO(GPIO_USER),            // 46      I                   GPIO46, Input only, Strapping
    0                            // Flag
  },
};

/*********************************************************************************************\
 Known templates
\*********************************************************************************************/

#elif CONFIG_IDF_TARGET_ESP32S3
/********************************************************************************************\
 * ESP32-S3 Module templates
\********************************************************************************************/

#define USER_MODULE        255

// Supported hardware modules
enum SupportedModulesESP32S3 {
  WEMOS,
  MAXMODULE };

// Default module settings
const uint8_t kModuleNiceList[] PROGMEM = {
  WEMOS,
};

// !!! Update this list in the same order as kModuleNiceList !!!
const char kModuleNames[] PROGMEM =
  "ESP32S3|"
  ;

// !!! Update this list in the same order as SupportedModulesESP32S2 !!!
const mytmplt kModules[] PROGMEM = {
  {                              // Generic ESP32C3 device
    AGPIO(GPIO_USER),            // 0       IO                  RTC_GPIO0, GPIO0, Strapping
    AGPIO(GPIO_USER),            // 1       AO                  RTC_GPIO1, GPIO1, TOUCH1, ADC1_CH0
    AGPIO(GPIO_USER),            // 2       AO                  RTC_GPIO2, GPIO2, TOUCH2, ADC1_CH1
    AGPIO(GPIO_USER),            // 3       AO                  RTC_GPIO3, GPIO3, TOUCH3, ADC1_CH2, Strapping
    AGPIO(GPIO_USER),            // 4       AO                  RTC_GPIO4, GPIO4, TOUCH4, ADC1_CH3
    AGPIO(GPIO_USER),            // 5       AO                  RTC_GPIO5, GPIO5, TOUCH5, ADC1_CH4
    AGPIO(GPIO_USER),            // 6       AO                  RTC_GPIO6, GPIO6, TOUCH6, ADC1_CH5
    AGPIO(GPIO_USER),            // 7       AO                  RTC_GPIO7, GPIO7, TOUCH7, ADC1_CH6
    AGPIO(GPIO_USER),            // 8       AO                  RTC_GPIO8, GPIO8, TOUCH8, ADC1_CH7, SUBSPICS1
    AGPIO(GPIO_USER),            // 9       AO                  RTC_GPIO9, GPIO9, TOUCH9, ADC1_CH8, SUBSPIHD, FSPIHD
    AGPIO(GPIO_USER),            // 10      AO                  RTC_GPIO10, GPIO10, TOUCH10, ADC1_CH9, FSPIIO4, SUBSPICS0, FSPICS0
    AGPIO(GPIO_USER),            // 11      AO                  RTC_GPIO11, GPIO11, TOUCH11, ADC2_CH0, FSPIIO5, SUBSPID, FSPID
    AGPIO(GPIO_USER),            // 12      AO                  RTC_GPIO12, GPIO12, TOUCH12, ADC2_CH1, FSPIIO6, SUBSPICLK, FSPICLK
    AGPIO(GPIO_USER),            // 13      AO                  RTC_GPIO13, GPIO13, TOUCH13, ADC2_CH2, FSPIIO7, SUBSPIQ, FSPIQ
    AGPIO(GPIO_USER),            // 14      AO                  RTC_GPIO14, GPIO14, TOUCH14, ADC2_CH3, FSPIDQS, SUBSPIWP, FSPIWP
    AGPIO(GPIO_USER),            // 15      AO                  RTC_GPIO15, GPIO15, U0RTS, ADC2_CH4, XTAL_32K_P
    AGPIO(GPIO_USER),            // 16      AO                  RTC_GPIO16, GPIO16, U0CTS, ADC2_CH5, XTAL_32K_N
    AGPIO(GPIO_USER),            // 17      AO                  RTC_GPIO17, GPIO17, U1TXD, ADC2_CH6
    AGPIO(GPIO_USER),            // 18      AO                  RTC_GPIO18, GPIO18, U1RXD, ADC2_CH7, CLK_OUT3
    AGPIO(GPIO_USER),            // 19      AO                  RTC_GPIO19, GPIO19, U1RTS, ADC2_CH8, CLK_OUT2, USB_D­
    AGPIO(GPIO_USER),            // 20      AO                  RTC_GPIO20, GPIO20, U1CTS, ADC2_CH9, CLK_OUT1, USB_D+
    AGPIO(GPIO_USER),            // 21      IO                  RTC_GPIO21, GPIO21
                                 // 22      --                  Unused
                                 // 23      --                  Unused
                                 // 24      --                  Unused
                                 // 25      --                  Unused
                                 // 26      FL                  SPICS1, GPIO26
                                 // 27      FL                  SPIHD, GPIO27
                                 // 28      FL                  SPIWP, GPIO28
                                 // 29      FL                  SPICS0, GPIO29
                                 // 30      FL                  SPICLK, GPIO30
                                 // 31      FL                  SPIQ, GPIO31
                                 // 32      FL                  SPID, GPIO32
    AGPIO(GPIO_NONE),            // 33      IO                  SPIIO4, GPIO33, FSPIHD, SUBSPIHD
    AGPIO(GPIO_NONE),            // 34      IO                  SPIIO5, GPIO34, FSPICS0, SUBSPICS0
    AGPIO(GPIO_NONE),            // 35      IO                  SPIIO6, GPIO35, FSPID, SUBSPID
    AGPIO(GPIO_NONE),            // 36      IO                  SPIIO7, GPIO36, FSPICLK, SUBSPICLK
    AGPIO(GPIO_NONE),            // 37      IO                  SPIDQS, GPIO37, FSPIQ, SUBSPIQ
    AGPIO(GPIO_USER),            // 38      IO                  GPIO38, FSPIWP, SUBSPIWP
    AGPIO(GPIO_USER),            // 39      IO                  MTCK, GPIO39, CLK_OUT3, SUBSPICS1
    AGPIO(GPIO_USER),            // 40      IO                  MTDO, GPIO40, CLK_OUT2
    AGPIO(GPIO_USER),            // 41      IO                  MTDI, GPIO41, CLK_OUT1
    AGPIO(GPIO_USER),            // 42      IO                  MTMS, GPIO42
    AGPIO(GPIO_USER),            // 43      IO                  U0TXD, GPIO43, CLK_OUT1
    AGPIO(GPIO_USER),            // 44      IO                  U0RXD, GPIO44, CLK_OUT2
    AGPIO(GPIO_USER),            // 45      IO                  GPIO45, Strapping
    AGPIO(GPIO_USER),            // 46      IO                  GPIO46, Strapping
    AGPIO(GPIO_USER),            // 47      IO                  SPICLK_P_DIFF, GPIO47, SUBSPICLK_P_DIFF
    AGPIO(GPIO_USER),            // 48      IO                  SPICLK_N_DIFF, GPIO48, SUBSPICLK_N_DIFF
    0                            // Flag
  },
};

/*********************************************************************************************\
 Known templates
\*********************************************************************************************/

#else  // not CONFIG_IDF_TARGET_ESP32C2/C3/C6 nor CONFIG_IDF_TARGET_ESP32S2 - ESP32
/********************************************************************************************\
 * ESP32 Module templates
\********************************************************************************************/

#define USER_MODULE        255

// Supported hardware modules
enum SupportedModulesESP32 {
  WEMOS,
  ESP32_CAM_AITHINKER,
  ODROID_GO,
  ESP32_SOLO,
  WT32_ETH01,
  TTGO_WATCH,
  M5STACK_CORE2,
  MAXMODULE };

// Default module settings
const uint8_t kModuleNiceList[] PROGMEM = {
  WEMOS,
#ifdef USE_WEBCAM
  ESP32_CAM_AITHINKER,
#endif  // USE_WEBCAM
#ifdef USE_ODROID_GO
  ODROID_GO,
#endif  // USE_ODROID_GO
#ifdef USE_ESP32_SOLO
//  ESP32_SOLO,                // To be defined
#endif  // USE_ESP32_SOLO
#ifdef USE_WT32_ETH01
  WT32_ETH01,
#endif  // USE_WT32_ETH01
#ifdef USE_TTGO_WATCH
//  TTGO_WATCH,                // To be defined
#endif  // USE_TTGO_WATCH
#ifdef USE_M5STACK_CORE2
  M5STACK_CORE2,
#endif  // USE_M5STACK_CORE2
};

// !!! Update this list in the same order as kModuleNiceList !!!
const char kModuleNames[] PROGMEM =
  "ESP32-DevKit|"
#ifdef USE_WEBCAM
  "ESP32-Cam|"
#endif  // USE_WEBCAM
#ifdef USE_ODROID_GO
  "Odroid Go|"
#endif  // USE_ODROID_GO
#ifdef USE_ESP32_SOLO
//  "ESP32-Solo|"              // To be defined
#endif  // USE_ESP32_SOLO
#ifdef USE_WT32_ETH01
  "WT32-Eth01|"
#endif  // USE_WT32_ETH01
#ifdef USE_TTGO_WATCH
//  "TTGO Watch|"              // To be defined
#endif  // USE_TTGO_WATCH
#ifdef USE_M5STACK_CORE2
  "M5Stack Core2|"
#endif  // USE_M5STACK_CORE2
  ;

// !!! Update this list in the same order as SupportedModulesESP32 !!!
const mytmplt kModules[] PROGMEM = {
  {                              // WEMOS - Espressif ESP32-DevKitC - Any ESP32 device like WeMos and NodeMCU hardware (ESP32)
    AGPIO(GPIO_USER),            // 0       (I)O                GPIO0, ADC2_CH1, TOUCH1, RTC_GPIO11, CLK_OUT1, EMAC_TX_CLK
    AGPIO(GPIO_USER),            // 1       IO     TXD0         GPIO1, U0TXD, CLK_OUT3, EMAC_RXD2
    AGPIO(GPIO_USER),            // 2       IO                  GPIO2, ADC2_CH2, TOUCH2, RTC_GPIO12, HSPIWP, HS2_DATA0, SD_DATA0
    AGPIO(GPIO_USER),            // 3       IO     RXD0         GPIO3, U0RXD, CLK_OUT2
    AGPIO(GPIO_USER),            // 4       IO                  GPIO4, ADC2_CH0, TOUCH0, RTC_GPIO10, HSPIHD, HS2_DATA1, SD_DATA1, EMAC_TX_ER
    AGPIO(GPIO_USER),            // 5       IO                  GPIO5, VSPICS0, HS1_DATA6, EMAC_RX_CLK
                                 // 6       IO                  Remapped to 28
                                 // 7       IO                  Remapped to 29
                                 // 8       IO                  Remapped to 30
    AGPIO(GPIO_USER),            // 9       IO                  GPIO9, Flash D2, U1RXD
    AGPIO(GPIO_USER),            // 10      IO                  GPIO10, Flash D3, U1TXD
                                 // 11      IO                  Remapped to 31
    AGPIO(GPIO_USER),            // 12      (I)O                GPIO12, ADC2_CH5, TOUCH5, RTC_GPIO15, MTDI, HSPIQ, HS2_DATA2, SD_DATA2, EMAC_TXD3       (If driven High, flash voltage (VDD_SDIO) is 1.8V not default 3.3V. Has internal pull-down, so unconnected = Low = 3.3V. May prevent flashing and/or booting if 3.3V flash is connected and pulled high. See ESP32 datasheet for more details.)
    AGPIO(GPIO_USER),            // 13      IO                  GPIO13, ADC2_CH4, TOUCH4, RTC_GPIO14, MTCK, HSPID, HS2_DATA3, SD_DATA3, EMAC_RX_ER
    AGPIO(GPIO_USER),            // 14      IO                  GPIO14, ADC2_CH6, TOUCH6, RTC_GPIO16, MTMS, HSPICLK, HS2_CLK, SD_CLK, EMAC_TXD2
    AGPIO(GPIO_USER),            // 15      (I)O                GPIO15, ADC2_CH3, TOUCH3, MTDO, HSPICS0, RTC_GPIO13, HS2_CMD, SD_CMD, EMAC_RXD3         (If driven Low, silences boot messages from normal boot. Has internal pull-up, so unconnected = High = normal output.)
    AGPIO(GPIO_USER),            // 16      IO                  GPIO16, HS1_DATA4, U2RXD, EMAC_CLK_OUT
    AGPIO(GPIO_USER),            // 17      IO                  GPIO17, HS1_DATA5, U2TXD, EMAC_CLK_OUT_180
    AGPIO(GPIO_USER),            // 18      IO                  GPIO18, VSPICLK, HS1_DATA7
    AGPIO(GPIO_USER),            // 19      IO                  GPIO19, VSPIQ, U0CTS, EMAC_TXD0
    0,                           // 20
    AGPIO(GPIO_USER),            // 21      IO                  GPIO21, VSPIHD, EMAC_TX_EN
    AGPIO(GPIO_USER),            // 22      IO      LED         GPIO22, VSPIWP, U0RTS, EMAC_TXD1
    AGPIO(GPIO_USER),            // 23      IO                  GPIO23, VSPID, HS1_STROBE
    0,                           // 24
    AGPIO(GPIO_USER),            // 25      IO                  GPIO25, DAC_1, ADC2_CH8, RTC_GPIO6, EMAC_RXD0
    AGPIO(GPIO_USER),            // 26      IO                  GPIO26, DAC_2, ADC2_CH9, RTC_GPIO7, EMAC_RXD1
    AGPIO(GPIO_USER),            // 27      IO                  GPIO27, ADC2_CH7, TOUCH7, RTC_GPIO17, EMAC_RX_DV
    0,                           // 6       IO                  GPIO6, Flash CLK
    0,                           // 7       IO                  GPIO7, Flash D0
    0,                           // 8       IO                  GPIO8, Flash D1
    0,                           // 11      IO                  GPIO11, Flash CMD
    AGPIO(GPIO_USER),            // 32      IO                  GPIO32, XTAL_32K_P (32.768 kHz crystal oscillator input), ADC1_CH4, TOUCH9, RTC_GPIO9
    AGPIO(GPIO_USER),            // 33      IO                  GPIO33, XTAL_32K_N (32.768 kHz crystal oscillator output), ADC1_CH5, TOUCH8, RTC_GPIO8
    AGPIO(GPIO_USER),            // 34      I   NO PULLUP       GPIO34, ADC1_CH6, RTC_GPIO4
    AGPIO(GPIO_USER),            // 35      I   NO PULLUP       GPIO35, ADC1_CH7, RTC_GPIO5
    AGPIO(GPIO_USER),            // 36      I   NO PULLUP       GPIO36, SENSOR_VP, ADC_H, ADC1_CH0, RTC_GPIO0
    0,                           // 37          NO PULLUP
    0,                           // 38          NO PULLUP
    AGPIO(GPIO_USER),            // 39      I   NO PULLUP       GPIO39, SENSOR_VN, ADC1_CH3, ADC_H, RTC_GPIO3
    0                            // Flag
  },

#ifdef USE_WEBCAM
  {                              // ESP32_CAM_AITHINKER - Any ESP32 device with webcam (ESP32)
    AGPIO(GPIO_WEBCAM_XCLK),     // 0       (I)O                GPIO0, CAM_XCLK
    AGPIO(GPIO_USER),            // 1       IO     TXD0         GPIO1, U0TXD, CLK_OUT3, EMAC_RXD2
    AGPIO(GPIO_SPI_MISO),        // 2       IO                  GPIO2, VSPI_MISO
    AGPIO(GPIO_USER),            // 3       IO     RXD0         GPIO3, U0RXD, CLK_OUT2
    AGPIO(GPIO_PWM1),            // 4       IO                  GPIO4, Flashlight
    AGPIO(GPIO_WEBCAM_DATA),     // 5       IO                  GPIO5, CAM_DATA1
                                 // 6       IO                  Remapped to 28
                                 // 7       IO                  Remapped to 29
                                 // 8       IO                  Remapped to 30
    AGPIO(GPIO_USER),            // 9       IO                  GPIO9, Flash D2, U1RXD
    AGPIO(GPIO_USER),            // 10      IO                  GPIO10, Flash D3, U1TXD
                                 // 11      IO                  Remapped to 31
    AGPIO(GPIO_USER),            // 12      (I)O                GPIO12, ADC2_CH5, TOUCH5, RTC_GPIO15, MTDI, HSPIQ, HS2_DATA2, SD_DATA2, EMAC_TXD3       (If driven High, flash voltage (VDD_SDIO) is 1.8V not default 3.3V. Has internal pull-down, so unconnected = Low = 3.3V. May prevent flashing and/or booting if 3.3V flash is connected and pulled high. See ESP32 datasheet for more details.)
    AGPIO(GPIO_SDCARD_CS),       // 13      IO                  GPIO13, VSPI_CS_TFLASH
    AGPIO(GPIO_SPI_CLK),         // 14      IO                  GPIO14, VSPI_CLK
    AGPIO(GPIO_SPI_MOSI),        // 15      (I)O                GPIO15, VSPI_MOSI                                                                       (If driven Low, silences boot messages from normal boot. Has internal pull-up, so unconnected = High = normal output.)
    AGPIO(GPIO_USER),            // 16      IO                  GPIO16, HS1_DATA4, U2RXD, EMAC_CLK_OUT
    AGPIO(GPIO_USER),            // 17      IO                  GPIO17, HS1_DATA5, U2TXD, EMAC_CLK_OUT_180
    AGPIO(GPIO_WEBCAM_DATA) +1,  // 18      IO                  GPIO18, CAM_DATA2
    AGPIO(GPIO_WEBCAM_DATA) +2,  // 19      IO                  GPIO19, CAM_DATA3
    0,                           // 20
    AGPIO(GPIO_WEBCAM_DATA) +3,  // 21      IO                  GPIO21, CAM_DATA4
    AGPIO(GPIO_WEBCAM_PCLK),     // 22      IO      LED         GPIO22, CAM_PCLK
    AGPIO(GPIO_WEBCAM_HREF),     // 23      IO                  GPIO23, CAM_HREF
    0,                           // 24
    AGPIO(GPIO_WEBCAM_VSYNC),    // 25      IO                  GPIO25, CAM_VSYNC
    AGPIO(GPIO_WEBCAM_SIOD),     // 26      IO                  GPIO26, CAM_SIOD
    AGPIO(GPIO_WEBCAM_SIOC),     // 27      IO                  GPIO27, CAM_SIOC
    0,                           // 6       IO                  GPIO6, Flash CLK
    0,                           // 7       IO                  GPIO7, Flash D0
    0,                           // 8       IO                  GPIO8, Flash D1
    0,                           // 11      IO                  GPIO11, Flash CMD
    AGPIO(GPIO_WEBCAM_PWDN),     // 32      IO                  GPIO32, CAM_PWDN
    AGPIO(GPIO_USER),            // 33      IO                  GPIO33, XTAL_32K_N (32.768 kHz crystal oscillator output), ADC1_CH5, TOUCH8, RTC_GPIO8
    AGPIO(GPIO_WEBCAM_DATA) +6,  // 34      I   NO PULLUP       GPIO34, CAM_DATA7
    AGPIO(GPIO_WEBCAM_DATA) +7,  // 35      I   NO PULLUP       GPIO35, CAM_DATA8
    AGPIO(GPIO_WEBCAM_DATA) +4,  // 36      I   NO PULLUP       GPIO36, CAM_DATA5
    0,                           // 37          NO PULLUP
    0,                           // 38          NO PULLUP
    AGPIO(GPIO_WEBCAM_DATA) +5,  // 39      I   NO PULLUP       GPIO39, CAM_DATA6
    0                            // Flag
  },
#endif  // USE_WEBCAM

#ifdef USE_ODROID_GO
  {                              // ODROID_GO - (ESP32)
    AGPIO(GPIO_KEY1),            // 0       (I)O                GPIO0, BTN-VOLUME
    AGPIO(GPIO_TXD),             // 1       IO     TXD0         GPIO1, TXD0
    AGPIO(GPIO_LEDLNK),          // 2       IO                  GPIO2, STATUS LED
    AGPIO(GPIO_RXD),             // 3       IO     RXD0         GPIO3, RXD0
    AGPIO(GPIO_USER),            // 4       IO                  GPIO4, ADC2_CH0, TOUCH0, RTC_GPIO10, HSPIHD, HS2_DATA1, SD_DATA1, EMAC_TX_ER
    AGPIO(GPIO_ILI9341_CS),      // 5       IO                  GPIO5, VSPI_CS0_LCD
                                 // 6       IO                  Remapped to 28
                                 // 7       IO                  Remapped to 29
                                 // 8       IO                  Remapped to 30
    0,                           // 9       IO                  GPIO9, Flash D2, U1RXD
    0,                           // 10      IO                  GPIO10, Flash D3, U1TXD
                                 // 11      IO                  Remapped to 31
    AGPIO(GPIO_USER),            // 12      (I)O                GPIO12, ADC2_CH5, TOUCH5, RTC_GPIO15, MTDI, HSPIQ, HS2_DATA2, SD_DATA2, EMAC_TXD3       (If driven High, flash voltage (VDD_SDIO) is 1.8V not default 3.3V. Has internal pull-down, so unconnected = Low = 3.3V. May prevent flashing and/or booting if 3.3V flash is connected and pulled high. See ESP32 datasheet for more details.)
    AGPIO(GPIO_KEY1) +1,         // 13      IO                  GPIO13, BTN-MENU
    AGPIO(GPIO_PWM1),            // 14      IO                  GPIO14, LCD Backlight
    AGPIO(GPIO_USER),            // 15      (I)O                GPIO15, ADC2_CH3, TOUCH3, MTDO, HSPICS0, RTC_GPIO13, HS2_CMD, SD_CMD, EMAC_RXD3         (If driven Low, silences boot messages from normal boot. Has internal pull-up, so unconnected = High = normal output.)
    AGPIO(GPIO_USER),            // 16      IO                  GPIO16, HS1_DATA4, U2RXD, EMAC_CLK_OUT
    AGPIO(GPIO_USER),            // 17      IO                  GPIO17, HS1_DATA5, U2TXD, EMAC_CLK_OUT_180
    AGPIO(GPIO_SPI_CLK),         // 18      IO                  GPIO18, VSPI_CLK
    AGPIO(GPIO_SPI_MISO),        // 19      IO                  GPIO19, VSPI_MISO
    0,                           // 20
    AGPIO(GPIO_ILI9341_DC),      // 21      IO                  GPIO21, SPI_DC_LCD
    AGPIO(GPIO_SDCARD_CS),       // 22      IO      LED         GPIO22, VSPI_CS1_TFLASH
    AGPIO(GPIO_SPI_MOSI),        // 23      IO                  GPIO23, VSPI_MOSI
    0,                           // 24
    0,                           // 25      IO                  GPIO25, DAC_1 (PAM8304A)
    0,                           // 26      IO                  GPIO26, DAC_2 (PAM8304A)
    AGPIO(GPIO_KEY1) +2,         // 27      IO                  GPIO27, BTN-SELECT
    0,                           // 6       IO                  GPIO6, Flash CLK
    0,                           // 7       IO                  GPIO7, Flash D0
    0,                           // 8       IO                  GPIO8, Flash D1
    0,                           // 11      IO                  GPIO11, Flash CMD
    AGPIO(GPIO_SWT1) +4,         // 32      IO                  GPIO32, BTN-A
    AGPIO(GPIO_SWT1) +5,         // 33      IO                  GPIO33, BTN-B
    AGPIO(GPIO_ADC_JOY),         // 34      I   NO PULLUP       GPIO34, JOY-X (LEFT-RIGHT)
    AGPIO(GPIO_ADC_JOY) +1,      // 35      I   NO PULLUP       GPIO35, JOY-Y (UP-DOWN)
    AGPIO(GPIO_ADC_RANGE) +2,    // 36      I   NO PULLUP       GPIO36, SENSOR_VP (BATTERY CARGER)
    0,                           // 37          NO PULLUP
    0,                           // 38          NO PULLUP
    AGPIO(GPIO_KEY1) +3,         // 39      I   NO PULLUP       GPIO39, BTN-START
    0                            // Flag
  },
#endif  // USE_ODROID_GO

#ifdef USE_ESP32_SOLO
//  {                              // ESP32 Solo (ESP32) - To be defined
//  },
#endif  // USE_ESP32_SOLO

#ifdef USE_WT32_ETH01
  {                              // WT32_ETH01 - (ESP32)
    0,                           // 0       (I)O                GPIO0, Ethernet EMAC_REF_CLK
    AGPIO(GPIO_USER),            // 1       IO     TXD0         GPIO1, U0TXD, CLK_OUT3, EMAC_RXD2
    AGPIO(GPIO_USER),            // 2       IO                  GPIO2, ADC2_CH2, TOUCH2, RTC_GPIO12, HSPIWP, HS2_DATA0, SD_DATA0
    AGPIO(GPIO_USER),            // 3       IO     RXD0         GPIO3, U0RXD, CLK_OUT2
    AGPIO(GPIO_USER),            // 4       IO                  GPIO4, ADC2_CH0, TOUCH0, RTC_GPIO10, HSPIHD, HS2_DATA1, SD_DATA1, EMAC_TX_ER
    AGPIO(GPIO_USER),            // 5       IO                  GPIO5, RXD Led green
                                 // 6       IO                  Remapped to 28
                                 // 7       IO                  Remapped to 29
                                 // 8       IO                  Remapped to 30
    0,                           // 9       IO                  GPIO9, Flash D2, U1RXD
    0,                           // 10      IO                  GPIO10, Flash D3, U1TXD
                                 // 11      IO                  Remapped to 31
    AGPIO(GPIO_USER),            // 12      (I)O                GPIO12, ADC2_CH5, TOUCH5, RTC_GPIO15, MTDI, HSPIQ, HS2_DATA2, SD_DATA2, EMAC_TXD3       (If driven High, flash voltage (VDD_SDIO) is 1.8V not default 3.3V. Has internal pull-down, so unconnected = Low = 3.3V. May prevent flashing and/or booting if 3.3V flash is connected and pulled high. See ESP32 datasheet for more details.)
    0,                           // 13      IO                  GPIO13, Ethernet EMAC_RX_ER
    AGPIO(GPIO_USER),            // 14      IO                  GPIO14, ADC2_CH6, TOUCH6, RTC_GPIO16, MTMS, HSPICLK, HS2_CLK, SD_CLK, EMAC_TXD2
    AGPIO(GPIO_USER),            // 15      (I)O                GPIO15, ADC2_CH3, TOUCH3, MTDO, HSPICS0, RTC_GPIO13, HS2_CMD, SD_CMD, EMAC_RXD3         (If driven Low, silences boot messages from normal boot. Has internal pull-up, so unconnected = High = normal output.)
    AGPIO(GPIO_OUTPUT_HI),       // 16      IO                  GPIO16, Ethernet OSC_ENA
    AGPIO(GPIO_LEDLNK_INV),      // 17      IO                  GPIO17, Network link led (green)
    AGPIO(GPIO_ETH_PHY_MDIO),    // 18      IO                  GPIO18, Ethernet MDIO
    0,                           // 19      IO                  GPIO19, Ethernet TXD0
    0,                           // 20
    0,                           // 21      IO                  GPIO21, Ethernet EMAC_TX_EN
    0,                           // 22      IO      LED         GPIO22, Ethernet EMAC_TXD1
    AGPIO(GPIO_ETH_PHY_MDC),     // 23      IO                  GPIO23, Ethernet MDC
    0,                           // 24
    0,                           // 25      IO                  GPIO25, Ethernet EMAC_RXD0
    0,                           // 26      IO                  GPIO26, Ethernet EMAC_RXD1
    0,                           // 27      IO                  GPIO27, Ethernet EMAC_RX_DV
    0,                           // 6       IO                  GPIO6, Flash CLK
    0,                           // 7       IO                  GPIO7, Flash D0
    0,                           // 8       IO                  GPIO8, Flash D1
    0,                           // 11      IO                  GPIO11, Flash CMD
    AGPIO(GPIO_USER),            // 32      IO                  GPIO32, CFG
    AGPIO(GPIO_USER),            // 33      IO                  GPIO33, 485_EN
    0,                           // 34      I   NO PULLUP       GPIO34, ADC1_CH6, RTC_GPIO4
    AGPIO(GPIO_USER),            // 35      I   NO PULLUP       GPIO35, ADC1_CH7, RTC_GPIO5
    AGPIO(GPIO_USER),            // 36      I   NO PULLUP       GPIO36, SENSOR_VP, ADC_H, ADC1_CH0, RTC_GPIO0
    0,                           // 37          NO PULLUP
    0,                           // 38          NO PULLUP
    AGPIO(GPIO_USER),            // 39      I   NO PULLUP       GPIO39, SENSOR_VN, ADC1_CH3, ADC_H, RTC_GPIO3
    0                            // Flag
  },
#endif  // USE_WT32_ETH01

#ifdef USE_TTGO_WATCH
//  {                              // TTGO Watch (ESP32) - To be defined
//  },
#endif  // USE_TTGO_WATCH

#ifdef USE_M5STACK_CORE2
  {                              // M5STACK CORE2 - (ESP32)
    AGPIO(GPIO_USER),            // 0       (I)O                GPIO0, SPKR_LRCK
    AGPIO(GPIO_USER),            // 1       IO     TXD0         GPIO1, U0TXD
    AGPIO(GPIO_USER),            // 2       IO                  GPIO2, SPKR_DATA
    AGPIO(GPIO_USER),            // 3       IO     RXD0         GPIO3, U0RXD
    AGPIO(GPIO_SDCARD_CS),       // 4       IO                  GPIO4, SPI_CS_CARD
    AGPIO(GPIO_ILI9341_CS),      // 5       IO                  GPIO5, SPI_CS_LCD
                                 // 6       IO                  Remapped to 28
                                 // 7       IO                  Remapped to 29
                                 // 8       IO                  Remapped to 30
    0,                           // 9       IO                  GPIO9, Flash D2, PSRAM_D3
    0,                           // 10      IO                  GPIO10, Flash D3, PSRAM_D2
                                 // 11      IO                  Remapped to 31
    0,                           // 12      (I)O                GPIO12, SPKR_CLK
    AGPIO(GPIO_USER),            // 13      IO                  GPIO13, ADC2_CH4, TOUCH4, RTC_GPIO14, MTCK, HSPID, HS2_DATA3, SD_DATA3, EMAC_RX_ER
    AGPIO(GPIO_USER),            // 14      IO                  GPIO14, ADC2_CH6, TOUCH6, RTC_GPIO16, MTMS, HSPICLK, HS2_CLK, SD_CLK, EMAC_TXD2
    AGPIO(GPIO_ILI9341_DC),      // 15      (I)O                GPIO15, SPI_DC_LCD
    0,                           // 16      IO                  GPIO16, PSRAM_CS
    0,                           // 17      IO                  GPIO17, PSRAM_CLK
    AGPIO(GPIO_SPI_CLK),         // 18      IO                  GPIO18, SPI_CLK
    AGPIO(GPIO_USER),            // 19      IO                  GPIO19, VSPIQ, U0CTS, EMAC_TXD0
    0,                           // 20
    0,                           // 21      IO                  GPIO21, I2C_SDA_INTERNAL
    0,                           // 22      IO      LED         GPIO22, I2C_SCL_INTERNAL
    AGPIO(GPIO_SPI_MOSI),        // 23      IO                  GPIO23, SPI_MOSI
    0,                           // 24
    AGPIO(GPIO_USER),            // 25      IO                  GPIO25, DAC_1, ADC2_CH8, RTC_GPIO6, EMAC_RXD0
    AGPIO(GPIO_USER),            // 26      IO                  GPIO26, DAC_2, ADC2_CH9, RTC_GPIO7, EMAC_RXD1
    AGPIO(GPIO_USER),            // 27      IO                  GPIO27, ADC2_CH7, TOUCH7, RTC_GPIO17, EMAC_RX_DV
    0,                           // 6       IO                  GPIO6, Flash CLK
    0,                           // 7       IO                  GPIO7, Flash D0
    0,                           // 8       IO                  GPIO8, Flash D1
    0,                           // 11      IO                  GPIO11, Flash CMD
    AGPIO(GPIO_I2C_SDA),         // 32      IO                  GPIO32, I2C_SDA
    AGPIO(GPIO_I2C_SCL),         // 33      IO                  GPIO33, I2C_SCL
    AGPIO(GPIO_USER),            // 34      I   NO PULLUP       GPIO34, ADC1_CH6, RTC_GPIO4
    AGPIO(GPIO_USER),            // 35      I   NO PULLUP       GPIO35, ADC1_CH7, RTC_GPIO5
    AGPIO(GPIO_USER),            // 36      I   NO PULLUP       GPIO36, SENSOR_VP, ADC_H, ADC1_CH0, RTC_GPIO0
    0,                           // 37          NO PULLUP
    AGPIO(GPIO_SPI_MISO),        // 38          NO PULLUP       GPIO38, SPI_MISO
    0,                           // 39      I   NO PULLUP       GPIO39, INT_TOUCHPAD
    0                            // Flag
  }
#endif  // USE_M5STACK_CORE2
};

/*********************************************************************************************\
 Known templates

{"NAME":"AITHINKER CAM","GPIO":[4992,1,1,1,1,5088,1,1,1,1,1,1,1,1,5089,5090,0,5091,5184,5152,0,5120,5024,5056,0,0,0,0,4928,1,5094,5095,5092,0,0,5093],"FLAG":0,"BASE":1}
{"NAME":"Olimex ESP32-PoE","GPIO":[1,1,1,1,1,1,0,0,5536,1,1,1,1,0,5600,0,0,0,0,5568,0,0,0,0,0,0,0,0,1,1,1,1,1,0,0,1],"FLAG":0,"BASE":1}
{"NAME":"wESP32","GPIO":[1,1,1,1,1,1,0,0,0,1,1,1,5568,5600,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1,1,1,1,1,0,0,1],"FLAG":0,"BASE":1}
{"NAME":"Denky (Teleinfo)","GPIO":[1,1,1,1,5664,1,1,1,1,1,1,1,1,1,1,1,0,1,1,1,0,1376,1,1,0,0,0,0,1,5632,1,1,1,0,0,1],"FLAG":0,"BASE":1}

\*********************************************************************************************/

#endif  // ESP32/S2/C3 selection
#endif  // ESP32

#endif  // _TASMOTA_TEMPLATE_H_