2018-03-23 16:20:20 +00:00
|
|
|
/* 5.12.0i
|
|
|
|
|
* Add 16 timers using commands Timer and Timers (#1091)
|
2018-03-28 17:01:38 +01:00
|
|
|
* Add commands Timer 0 to clear timer and Timer 1..16 to copy timer
|
|
|
|
|
* Add optional Timer configuration webpage to be enabled in user_config.h with define USE_TIMERS_WEB
|
2018-04-02 13:19:57 +01:00
|
|
|
* Add hexadecimal Data entry to command IrSend using 0x notation (#1290, #2314)
|
2018-04-01 20:37:00 +01:00
|
|
|
* Add Domoticz Battery and RSSI Quality (#1604)
|
2018-03-29 13:51:34 +01:00
|
|
|
* Add Home Assistant MQTT Discovery for Buttons and change SetOption19 response (#2277)
|
2018-03-31 15:26:00 +01:00
|
|
|
* Add support for SGP30 gas and air quality sensor (#2307)
|
2018-04-01 10:04:00 +01:00
|
|
|
* Add multiple color entry support for command Led like Led2 120000 001200 000012 setting led2 as Red, Led3 as Green and Led4 as Blue (#2303)
|
2018-04-02 14:00:26 +01:00
|
|
|
* Add hexadecimal RGB color entry on RGBCW leds (#2304)
|
2018-03-28 17:01:38 +01:00
|
|
|
* Change webpage parameter communication
|
2018-03-30 10:15:04 +01:00
|
|
|
* Change Timer parameter Device to more obvious Output
|
2018-03-31 18:56:16 +01:00
|
|
|
* Change max number of commands in Backlog from 15 to 30 and ignore commands overflowing
|
2018-04-02 13:19:57 +01:00
|
|
|
* Change user_config_override usage by providing user_config_override_sample.h (#2228)
|
2018-03-31 15:26:00 +01:00
|
|
|
* Change MQTT response topic for Energy changes from ENERGY to SENSOR (#2229, #2251)
|
|
|
|
|
* Change default Reset configuration time from 4 seconds to 40 seconds on Button hold (#2268)
|
2018-03-23 16:20:20 +00:00
|
|
|
*
|
|
|
|
|
* 5.12.0h
|
2018-03-21 16:58:39 +00:00
|
|
|
* Add optional Arduino OTA support to be enabled in user_config.h (#1998)
|
2018-03-20 13:31:11 +00:00
|
|
|
* Add support for Software Serial bridge using commands SerialDelimiter, SBaudrate and SSerialSend. Supports 8N1 and text only (#2190)
|
|
|
|
|
* Add support for Hardware Serial bridge using commands SerialDelimiter, Baudrate and SerialSend. Supports 8N1 and text only (#2182)
|
2018-03-21 08:27:05 +00:00
|
|
|
* Add support for Zengge WF017 PWM Led strip controller (#2202)
|
2018-03-20 15:28:18 +00:00
|
|
|
* Add PWM status to command State if PWM enabled (#2203)
|
|
|
|
|
* Add command HSBColor Hue,Sat,Bri (#1642, #2203)
|
|
|
|
|
* Add command Channel 0..100 to control dimmer value for individual color channels (#2111, #2203)
|
2018-03-21 08:56:39 +00:00
|
|
|
* Add Channel status information (#2211)
|
2018-03-21 09:42:56 +00:00
|
|
|
* Add all FriendlyNames to Status information (#2208)
|
|
|
|
|
* Change status display of Ssid and SetOption
|
2018-03-21 08:27:05 +00:00
|
|
|
* Change default option SetOption15 from 0 to 1 providing better initial PWM experience
|
2018-03-18 12:47:30 +00:00
|
|
|
*
|
|
|
|
|
* 5.12.0f
|
2018-03-17 14:22:29 +00:00
|
|
|
* Add compile time support for WS2812 BRG and RBG led configurations to be defined in user_config.h (#1690)
|
|
|
|
|
*
|
|
|
|
|
* 5.12.0e
|
2018-03-12 13:56:48 +00:00
|
|
|
* Add Domoticz dust (custom) sensors to PMS5003 and NovaFitness SDS drivers as PM1, PM2.5 and PM10
|
2018-03-09 17:08:17 +00:00
|
|
|
* Add a second TLS fingerprint to allow switching keys in TLS mode (#2033, #2102)
|
2018-03-11 14:46:58 +00:00
|
|
|
* Add display of remaining pulse time to command PulseTime (#2085)
|
|
|
|
|
* Add additional time offset to Wifi Retry based on device mac address (#2089)
|
|
|
|
|
* Add command Color6 RRGGBB for Clock hour marker color and command Rotation pixels for Clock rotation (#2092)
|
2018-03-10 13:51:40 +00:00
|
|
|
* Add HTML language header in local language (#2123)
|
2018-03-14 13:32:51 +00:00
|
|
|
* Add command PowerDelta 0..100 (percentage) to Energy monitoring devices to report on active power load change (#2157)
|
2018-03-14 16:28:30 +00:00
|
|
|
* Add Restart Reason to Status 1 report (#2161)
|
2018-03-11 16:44:58 +00:00
|
|
|
* Fix MAX31850 higher temperatures (#1269)
|
2018-03-09 17:08:17 +00:00
|
|
|
*
|
|
|
|
|
* 5.12.0d
|
2018-03-02 14:38:37 +00:00
|
|
|
* Add support for optional MQTT drivers to be selected in user_config.h (#1992)
|
2018-02-28 17:01:40 +00:00
|
|
|
* Add Portuguese language file
|
2018-02-27 13:59:46 +00:00
|
|
|
* Add compiler check for stable lwIP version v1.4 (#1940)
|
2018-03-08 16:53:02 +00:00
|
|
|
* Add always suffix with device number in Mqtt discovery topic (#1962)
|
2018-02-27 13:59:46 +00:00
|
|
|
* Add diacritics to Polish language file (#2005)
|
|
|
|
|
* Add Hungarian language file (#2024)
|
2018-03-08 13:02:00 +00:00
|
|
|
* Add Czech language file
|
|
|
|
|
* Add Chinese (Traditional) in Taiwan language file (#2108)
|
2018-03-03 14:28:30 +00:00
|
|
|
* Add support for Nova Fitness SDS011 and possibly SDS021 particle concentration sensor (#2070)
|
2018-03-08 16:53:02 +00:00
|
|
|
* Add single decimal precision to Nova Fitness SDS0x1 sensor values (#2093)
|
2018-03-09 11:13:40 +00:00
|
|
|
* Add support for multiple SHT3X sensors (#1949, #2110)
|
2018-03-09 12:47:44 +00:00
|
|
|
* Add Sonoff SC domoticz support for Sound level as Counter and Air quality (#2118)
|
2018-02-27 13:59:46 +00:00
|
|
|
* Fix MQTT TLS fingerprint validation (#2033)
|
|
|
|
|
*
|
|
|
|
|
* 5.12.0c
|
2018-02-20 15:19:48 +00:00
|
|
|
* Fix intermittent exception when dns lookup is used while sleep is enabled
|
2018-02-24 15:37:33 +00:00
|
|
|
* Fix 5.4.0 regression turning off single press after button hold during 4x hold time
|
|
|
|
|
* Fix possible wifi connection problem by erasing sdk configuration parameters
|
2018-02-27 13:59:46 +00:00
|
|
|
* Change Polish language to using Diacritics (#2005)
|
2018-02-20 15:19:48 +00:00
|
|
|
*
|
|
|
|
|
* 5.12.0b
|
2018-02-13 13:30:30 +00:00
|
|
|
* Add serial debug info
|
2018-02-18 17:39:28 +00:00
|
|
|
* Add Multichannel Gas sensor using MultiChannel_Gas_Sensor library (#1245)
|
2018-02-13 13:30:30 +00:00
|
|
|
* Add optional usage of %d or %X suffices in MQTT client to append chipid (#1871)
|
|
|
|
|
* Add optional usage of %d or %X suffices in MQTT topic to append chipid (#1871)
|
|
|
|
|
* Add optional usage of %d or %04d in ota url to be replaced with chipid (#1871)
|
2018-02-18 15:47:26 +00:00
|
|
|
* Add Sonoff Bridge command RfKey<x> 5 to show current RF key values either default or learned (#1884)
|
2018-02-13 13:30:30 +00:00
|
|
|
* Add user configurable serial GPIOs to MagicHome and Arilux modules (#1887)
|
2018-02-15 11:29:07 +00:00
|
|
|
* Add Russian language file (#1909)
|
2018-02-16 16:35:51 +00:00
|
|
|
* Add Webserver upload preflight request support (#1927)
|
|
|
|
|
* Add Home Assistant clear other device (#1931)
|
2018-02-17 12:47:11 +00:00
|
|
|
* Add Restart time to Status 1 (#1938)
|
2018-02-20 15:10:31 +00:00
|
|
|
* Change TSL2561 driver to joba library and delete Adafruit library (#1644)
|
2018-02-17 12:47:11 +00:00
|
|
|
* Change Sonoff SC JSON format (#1939)
|
2018-02-17 13:09:39 +00:00
|
|
|
* Fix compile error when define HOME_ASSISTANT_DISCOVERY_ENABLE is not set (#1937)
|
2018-02-18 16:31:14 +00:00
|
|
|
* Add optional TSL2561 driver using library Joba_Tsl2561 to be enabled in user_config.h with define USE_TSL2561_JOBA (#1951)
|
2018-02-19 14:33:06 +00:00
|
|
|
* Add support for sensor SHTC3 (#1967)
|
2018-02-13 13:30:30 +00:00
|
|
|
*
|
|
|
|
|
* 5.12.0a
|
2018-02-10 14:13:27 +00:00
|
|
|
* Change platformio option sonoff-ds18x20 to sonoff-xxl enabling ds18x20 and all other sensors in one image
|
|
|
|
|
* Fix providing web page configuratin option for Friendly Name when no device (relay or light) is configured (#1850)
|
2018-02-20 15:19:48 +00:00
|
|
|
* Change default parameters in user_config.h to undefined for easy installation (#1851)
|
2018-02-10 14:13:27 +00:00
|
|
|
* Change max user configurable hold time from 10 to 25 seconds (#1851)
|
2018-02-07 16:50:02 +00:00
|
|
|
*
|
2018-02-09 16:16:39 +00:00
|
|
|
* 5.12.0 20180209
|
|
|
|
|
* Change library PubSubClient.h define MQTT_MAX_PACKET_SIZE from 512 to 1000 for Home Assistant support
|
|
|
|
|
* Change relation of define MESSZ being dependent on PubSubClient.h define MQTT_MAX_PACKET_SIZE
|
|
|
|
|
* Change command color parameter input checks to less strict for Home Assistant support
|
|
|
|
|
* Change command Ina219Mode into command Sensor13
|
|
|
|
|
* Change commands HlwPCal, HlwUCal and HlwICal to PowerCal, VoltageCal and CurrentCal to be used for both Pow and S31 calibration
|
|
|
|
|
* Change commands HlwPSet, HlwUSet and HlwISet to PowerSet, VoltageSet and CurrentSet to be used for both Pow and S31 calibration
|
|
|
|
|
* Change uptime from hour to second resulting in a display of 123T13:45:21 where 123 is days
|
|
|
|
|
* Change module name Wemos D1 mini into Generic (#1220)
|
|
|
|
|
* Change HTML from width=100% to style=width:100% supporting HTML5 (#1358)
|
|
|
|
|
* Change OSWATCH_RESET_TIME (Blocked loop) from 30 to 120 seconds to allow slow networks (#1556)
|
|
|
|
|
* Change WIFI_MANAGER_SEC into WIFI_CONFIG_SEC (#1616)
|
|
|
|
|
* Change function pointers code to save code space and memory (#1683)
|
|
|
|
|
* Change webserver argument processing gaining 5k code space (#1705)
|
|
|
|
|
* Change weblog memory usage (#1730, #1793, #1819)
|
2018-02-03 22:25:05 +00:00
|
|
|
* Update TasmotaSerial library to 1.1.0
|
2018-02-09 16:16:39 +00:00
|
|
|
* Update language files Italian (#1594), Dutch (#1723) and Spanish (#1722)
|
|
|
|
|
* Fix Non-English JSON temperature unit attachement
|
|
|
|
|
* Fix Arilux RF induced exception by moving interrupt handler to iram on non ESP8266/Arduino lib v2.3.0
|
|
|
|
|
* Fix truncated command names and wrong response for DomoticzSwitchIdx (#1571)
|
|
|
|
|
* Fix %-sign issue as printf escape character in Humidity and Sonoff SC (#1579)
|
|
|
|
|
* Fix DS18B20 temperature JSON decimal dot (#1561)
|
|
|
|
|
* Fix Energy JSON message (#1621)
|
|
|
|
|
* Fix IRSend parameter translation (#1636)
|
|
|
|
|
* Fix TSL2561 device detection (#1644, #1825)
|
|
|
|
|
* Fix BME680 teleperiod resistance measuring (#1647)
|
|
|
|
|
* Fix Energy Monitoring Energy Today and Energy Total reading after restart (#1648)
|
2018-02-03 22:25:05 +00:00
|
|
|
* Fix IRReceive Data value (#1663)
|
2018-02-09 16:16:39 +00:00
|
|
|
* Fix Energy Monitoring Energy Period roll-over (#1688)
|
2018-02-03 22:25:05 +00:00
|
|
|
* Fix compiler warnings (#1774)
|
2018-02-06 09:06:22 +00:00
|
|
|
* Fix command PWM response if no PWM channel is configured (#1783)
|
2018-01-20 11:12:39 +00:00
|
|
|
* Add locale Decimal Separator to Web sensor page
|
2018-01-18 15:19:28 +00:00
|
|
|
* Add ColorTemperature to light status message
|
2018-01-13 14:53:02 +00:00
|
|
|
* Add command PowerOnState option 5 which inverts PulseTime and allows for delayed always on after power on
|
|
|
|
|
* Add OtaMagic two step Web server OTA upgrade using filename-minimal image if OTA free space is too small
|
2018-02-09 16:16:39 +00:00
|
|
|
* Add support for PMS5003 and PMS7003 particle concentration sensor
|
|
|
|
|
* Add command SetOption21 1 to allow Energy Monitoring when power is off on Sonoff Pow and Sonoff S31 (#1420)
|
|
|
|
|
* Add Chinese language file (#1551)
|
|
|
|
|
* Add French language file (#1561)
|
|
|
|
|
* Add Spanish language file (#1589)
|
|
|
|
|
* Add HTTP Allow Cross Origin removed from ESP8266/Arduino lib v2.4.0 (#1572)
|
|
|
|
|
* Add Home Assistant MQTT Discovery for switch and light to be enabled by command SetOption19 1 (#1534) or define HOME_ASSISTANT_DISCOVERY_ENABLE in user_config.h (#1685)
|
|
|
|
|
* Add command State to retrieve device state information (same data as teleperiod state and status 11 in slightly different JSON format)
|
|
|
|
|
* Add optional login to Webserver AP mode (#1587, #1635)
|
|
|
|
|
* Add command Sensor15 2 to start MHZ19(B) Zero Point Calibration (#1643)
|
|
|
|
|
* Add support for Sonoff S31 Smart Socket with Power Consumption Detection (#1626)
|
|
|
|
|
* Add command SetOption20 to allow update of Dimmer/Color/Ct without turning power on (#1719, #1741)
|
|
|
|
|
* Add NTP sync time slot based on chip id (#1773)
|
|
|
|
|
* Add cursor pointer to web button (#1836)
|
2018-01-08 10:44:18 +00:00
|
|
|
*
|
|
|
|
|
* 5.11.1 20180107
|
|
|
|
|
* Fix Sonoff Pow command handling (#1542)
|
2018-01-06 16:34:42 +00:00
|
|
|
*
|
2018-01-07 13:56:23 +00:00
|
|
|
* 5.11.0 20180107
|
|
|
|
|
* Minor webpage HTML optimizations (#1358)
|
2017-12-27 13:10:55 +00:00
|
|
|
* Updated German translation (#1438)
|
2017-12-18 17:20:28 +00:00
|
|
|
* Change Sonoff Pow Energy MQTT data message and consolidate Status 8 into Status 10
|
2018-01-07 13:56:23 +00:00
|
|
|
* Change ADS1115 default voltage range from +/-2V to +/-6V (#1289)
|
|
|
|
|
* Change text to Active for 3 minutes (#1364)
|
2017-12-17 15:01:30 +00:00
|
|
|
* Change Wemo SetBinaryState to distinguish from GetBinaryState (#1357)
|
2017-12-22 13:55:24 +00:00
|
|
|
* Change output of HTTP command to valid JSON and Array only (#1363)
|
2018-01-07 13:56:23 +00:00
|
|
|
* Removed all MQTT, JSON and Command language defines from locale files and set fixed to English (#1473)
|
|
|
|
|
* Renamed commands Color2,3,4 to Color3,4,5
|
|
|
|
|
* Fix BME280 calculation (#1051)
|
|
|
|
|
* Fix Sonoff Bridge missed learned key if learned data contains 0x55 (End of Transmission) flag (#1095, #1294)
|
|
|
|
|
* Fix PWM initialization in Dimmer/Color mode (#1321)
|
|
|
|
|
* Fix Wemo Emulation (#1357)
|
|
|
|
|
* Fix display of build date and time in non-english locale (#1465)
|
|
|
|
|
* Fix Wemo and Hue emulation by adding M-Search response delay (#1486)
|
|
|
|
|
* Add libraries Adafruit_BME680-1.0.5, Adafruit_Sensor-1.0.2.02, TasmotaSerial-1.0.0 and TSL2561-Arduino-Library
|
|
|
|
|
* Add command Color2 to set color while keeping same dimmer value
|
|
|
|
|
* Add device function pointers
|
|
|
|
|
* Add support for SenseAir S8 CO2 sensor
|
|
|
|
|
* Add color led signal to Carbon Dioxide (CO2) sensors using defines CO2_LOW and CO2_HIGH in user_config.h
|
2017-12-22 13:55:24 +00:00
|
|
|
* Add support for Domoticz Air Quality sensor to be used by MH-Z19(B) and SenseAir sensors
|
2018-01-07 13:56:23 +00:00
|
|
|
* Add support for PZEM004T energy sensor
|
2017-12-04 16:25:06 +00:00
|
|
|
* Add support for iTead SI7021 temperature and humidity sensor by consolidating DHT22 into AM2301 and using former DHT22 as SI7021 (#735)
|
2017-12-06 16:14:41 +00:00
|
|
|
* Add support for BME680 using adafruit libraries (#1212)
|
2018-01-07 13:56:23 +00:00
|
|
|
* Add support for MH-Z19(B) CO2 sensor (#561, #1248)
|
|
|
|
|
* Add multipress support and more user configurable GPIO to Sonoff Dual R2 (#1291)
|
2017-12-06 16:14:41 +00:00
|
|
|
* Add support for TSL2561 using adafruit library (#661, #1311)
|
2018-01-07 13:56:23 +00:00
|
|
|
* Add support for SHT3x (#1314)
|
|
|
|
|
* Add support for Arilux LC06 (#1414)
|
|
|
|
|
* Add Italian language file (#1449)
|
|
|
|
|
* Add 2nd Gen Alexa support to Wemo emulation discovery (#1357, #1450)
|
|
|
|
|
* Add define for additional number of WS2812 schemes (#1463)
|
2017-12-01 14:59:53 +00:00
|
|
|
*
|
|
|
|
|
* 5.10.0 20171201
|
|
|
|
|
* Upgrade library ArduinoJson to 5.11.2
|
|
|
|
|
* Upgrade library IRRemoteEsp8266 to 2.2.1 + 2 commits but disabled some protocols (code size reduction)
|
|
|
|
|
* Upgrade library NeoPixelBus to 2.2.9
|
|
|
|
|
* Upgrade library OneWire to 2.3.3 + 6 commits and disabled CRC lookup-table (#define ONEWIRE_CRC8_TABLE 0) (code size reduction)
|
|
|
|
|
* Update library PubSubClient to 2.6 + 9 commits and additional delay (#790)
|
|
|
|
|
* Update core_esp8266_wiring_digital.c to latest (staged) level
|
|
|
|
|
* Patch library I2Cdevlib-Core for esp8266-core 2.4.0-rc2 compatibility
|
|
|
|
|
* Remove command EnergyReset 1..3 now replaced by EnergyReset1 to EnergyReset3
|
|
|
|
|
* Remove spaces in JSON messages (code size reduction)
|
|
|
|
|
* Renamed xsns_05_ds18x20.ino to xsns_05_ds18x20_legacy.ino still using library OneWire and providing dynamic sensor scan
|
|
|
|
|
* Fix possible iram1_0_seg compile error by shrinking ICACHE_RAM_ATTR code usage
|
|
|
|
|
* Fix PWM watchdog timeout if Dimmer is set to 100 or Color set to 0xFF (#1146)
|
|
|
|
|
* Fix Sonoff Bridge Learn Mode hang caused by unrecognised RF code (#1181)
|
|
|
|
|
* Fix blank console log window by using XML character encoding (#1187)
|
|
|
|
|
* Fix wrong response name for command HlwISet (#1214)
|
|
|
|
|
* Fix DHT type sensor timeout recognition by distinguish "signal already there" from "timeout" (#1233)
|
|
|
|
|
* Add fixed color options 1..12 to command Color
|
|
|
|
|
* Add + (plus) and - (minus) to commands Dimmer (+10/-10), Speed and Scheme
|
|
|
|
|
* Add + (plus) and - (minus) to command Color to select 1 out of 12 preset colors
|
|
|
|
|
* Add + (plus) and - (minus) to command Ct to control ColdWarm led ColorTemperature (+34/-34)
|
|
|
|
|
* Add commands EnergyReset1 0..42500, EnergyReset2 0..42500 and EnergyReset3 0..42500000
|
|
|
|
|
* to (Re)set Energy Today, Yesterday or Total respectively in Wh (#406, #685, #1202)
|
|
|
|
|
* Add optional ADS1115 driver as alternative for unsupported I2Cdevlib in esp8266-core 2.4.0-rc2
|
|
|
|
|
* Add support for INA219 Voltage and Current sensor to be enabled in user_config.h with define USE_INA219
|
|
|
|
|
* Add support for Arilux LC11 (Clearing RF home code when selecting no Arilux module)
|
|
|
|
|
* Add support for WS2812 RGBW ledstrips to be enabled in user_config.h with define USE_WS2812_CTYPE (#1156)
|
|
|
|
|
* Add SettingsSaveAll routine to command SaveData to be used before controlled power down (#1202)
|
|
|
|
|
* Add option PUSHBUTTON_TOGGLE (SwitchMode 7) to allow toggling on any switch change (#1221)
|
v5.9.1j - Add Dual R2, Rewrite DS18x20 and fixes
5.9.1j
* Revert changes to xsns_05_ds18x20.ino and rename to
xsns_05_ds18x20_legacy.ino still needing library OneWire and providing
legacy JSON message:
*
"DS18x20":{"DS1":{"Type":"DS18B20","Address":"284CC48E04000079","Temperature":19.5},"DS2":{"Type":"DS18B20","Address":"283AC28304000052","Temperature":19.6}}
* Add new xdrv_05_ds18x20.ino free from library OneWire and add the
following features:
* Add support for DS1822
* Add forced setting of
12-bit resolution for selected device types (#1222)
* Add read
temperature retry counter (#1215)
* Fix lost sensors by performing
sensor probe at restart only thereby removing dynamic sensor probe
(#1215)
* Fix sensor address sorting using ascending sort on sensor
type followed by sensor address
* Rewrite JSON resulting in shorter
message allowing more sensors in default firmware image:
*
"DS18B20-1":{"Id":"00000483C23A","Temperature":19.5},"DS18B20-2":{"Id":"0000048EC44C","Temperature":19.6}
* Add additional define in user_config.h to select either single sensor
(defines disabled), new multi sensor (USE_DS18X20) or legacy multi
sensor (USE_DS18X20_LEGACY)
* Add support for Sonoff Dual R2 (#1249)
*
Fix ADS1115 detection (#1258)
2017-11-27 16:46:51 +00:00
|
|
|
* Add new xdrv_05_ds18x20.ino free from library OneWire and add the following features:
|
|
|
|
|
* Add support for DS1822
|
|
|
|
|
* Add forced setting of 12-bit resolution for selected device types (#1222)
|
|
|
|
|
* Add read temperature retry counter (#1215)
|
|
|
|
|
* Fix lost sensors by performing sensor probe at restart only thereby removing dynamic sensor probe (#1215)
|
|
|
|
|
* Fix sensor address sorting using ascending sort on sensor type followed by sensor address
|
|
|
|
|
* Rewrite JSON resulting in shorter message allowing more sensors in default firmware image:
|
|
|
|
|
* "DS18B20-1":{"Id":"00000483C23A","Temperature":19.5},"DS18B20-2":{"Id":"0000048EC44C","Temperature":19.6}
|
|
|
|
|
* Add additional define in user_config.h to select either single sensor (defines disabled), new multi sensor (USE_DS18X20) or legacy multi sensor (USE_DS18X20_LEGACY)
|
2017-12-01 14:59:53 +00:00
|
|
|
* Add clock support for more different pixel counts (#1226)
|
v5.9.1j - Add Dual R2, Rewrite DS18x20 and fixes
5.9.1j
* Revert changes to xsns_05_ds18x20.ino and rename to
xsns_05_ds18x20_legacy.ino still needing library OneWire and providing
legacy JSON message:
*
"DS18x20":{"DS1":{"Type":"DS18B20","Address":"284CC48E04000079","Temperature":19.5},"DS2":{"Type":"DS18B20","Address":"283AC28304000052","Temperature":19.6}}
* Add new xdrv_05_ds18x20.ino free from library OneWire and add the
following features:
* Add support for DS1822
* Add forced setting of
12-bit resolution for selected device types (#1222)
* Add read
temperature retry counter (#1215)
* Fix lost sensors by performing
sensor probe at restart only thereby removing dynamic sensor probe
(#1215)
* Fix sensor address sorting using ascending sort on sensor
type followed by sensor address
* Rewrite JSON resulting in shorter
message allowing more sensors in default firmware image:
*
"DS18B20-1":{"Id":"00000483C23A","Temperature":19.5},"DS18B20-2":{"Id":"0000048EC44C","Temperature":19.6}
* Add additional define in user_config.h to select either single sensor
(defines disabled), new multi sensor (USE_DS18X20) or legacy multi
sensor (USE_DS18X20_LEGACY)
* Add support for Sonoff Dual R2 (#1249)
*
Fix ADS1115 detection (#1258)
2017-11-27 16:46:51 +00:00
|
|
|
* Add support for Sonoff Dual R2 (#1249)
|
2017-12-01 14:59:53 +00:00
|
|
|
* Add FriendlyName to web page tab and add program information to web page footer (#1275)
|
2017-11-07 14:57:24 +00:00
|
|
|
*
|
2017-11-08 10:57:16 +00:00
|
|
|
* 5.9.1 20171107
|
2017-11-03 17:07:25 +00:00
|
|
|
* Add external sensor function pointer interface to enable easy sensor addition
|
2017-11-08 10:57:16 +00:00
|
|
|
* Add support for ADS1115 to be enabled in user_config.h and needs libraries i2cdevlib-Core and i2cdevlib-ADS1115 (#338, #660)
|
2017-11-03 17:07:25 +00:00
|
|
|
* Fix Backup Configuration file download failure by defining proper file size (#1115)
|
2017-11-08 10:57:16 +00:00
|
|
|
* Fix Exception 26 and empty console screen after usage of command WakeupDuration (#1133)
|
|
|
|
|
* Fix some changed iTead web links in README.md (#1137)
|
2017-10-23 11:18:15 +01:00
|
|
|
*
|
2017-11-03 17:07:25 +00:00
|
|
|
* 5.9.0 20171030
|
2017-10-18 17:22:34 +01:00
|
|
|
* Rewrite code (partly) using Google C++ Style Guide (https://google.github.io/styleguide/cppguide.html)
|
2017-11-03 17:07:25 +00:00
|
|
|
* Rewrite code by using command lookup tables and javascript (client side) web page expansions
|
|
|
|
|
* Change HTML/CSS to enable nicer form field entry
|
2017-10-01 13:32:36 +01:00
|
|
|
* Change default PWM assignments for H801 RGB(CW) led controller to support optional Color/Dimmer control
|
|
|
|
|
* GPIO04 (W2) from GPIO_PWM2 to GPIO_USER to be user configurable for GPIO_PWM5 (second White - Warm if W1 is Cold)
|
|
|
|
|
* GPIO12 (Blue) GPIO_PWM3 no change
|
|
|
|
|
* GPIO13 (Green) from GPIO_PWM4 to GPIO_PWM2
|
|
|
|
|
* GPIO14 (W1) from GPIO_PWM1 to GPIO_USER to be user configurable for GPIO_PWM4 (first White - Cold or Warm)
|
|
|
|
|
* GPIO15 (Red) from GPIO_PWM5 to GPIO_PWM1
|
|
|
|
|
* Change default PWM assignments for MagicHome RGB(W) led controller to support optional Color/Dimmer control
|
|
|
|
|
* GPIO05 (Green) from GPIO_PWM4 to GPIO_PWM2
|
|
|
|
|
* GPIO12 (Blue) from GPIO_PWM5 to GPIO_PWM3
|
|
|
|
|
* GPIO13 (White) GPIO_USER to be user configurable for GPIO_PWM4 (White - Cold or Warm)
|
|
|
|
|
* GPIO14 (Red) from GPIO_PWM3 to GPIO_PWM1
|
2017-11-03 17:07:25 +00:00
|
|
|
* Change default PWM assignment for Witty Cloud to support optional Color/Dimmer control (#976)
|
|
|
|
|
* GPIO12 (Green) from GPIO_PWM4 to GPIO_PWM2
|
|
|
|
|
* GPIO13 (Blue) from GPIO_PWM5 to GPIO_PWM3
|
|
|
|
|
* GPIO15 (Red) from GPIO_PWM3 to GPIO_PWM1
|
|
|
|
|
* Change when another module is selected now all GPIO user configuration is removed
|
|
|
|
|
* Change command name IRRemote to IRSend (#956)
|
|
|
|
|
* Remove Arduino IDE version too low warning as it interferes with platformio.ini platform = espressif8266_stage
|
2017-09-26 14:10:58 +01:00
|
|
|
* Fix command FullTopic entry when using serial or console interface
|
|
|
|
|
* Fix possible UDP syslog blocking
|
2017-11-03 17:07:25 +00:00
|
|
|
* Fix minimum TelePeriod of 10 seconds set by web page
|
|
|
|
|
* Fix command GPIOx JSON response (#897)
|
|
|
|
|
* Fix inverted relay power on state (#909)
|
|
|
|
|
* Fix compile error when DOMOTICZ_UPDATE_TIMER is not defined (#930)
|
|
|
|
|
* Fix alignment of web page items in some browsers (#935)
|
|
|
|
|
* Fix setting all saved power settings to Off when SetOption0 (SaveState) = 0 (#955)
|
|
|
|
|
* Fix timezone range from -12/12 to -13/13 (#968)
|
|
|
|
|
* Fix Southern Hemisphere TIME_STD/TIME_DST (#968)
|
|
|
|
|
* Fix TLS MQTT SSL fingerprint test (#970, #808)
|
|
|
|
|
* Fix virtual relay status message used with Color/Dimmer control (#989)
|
|
|
|
|
* Fix command IRSend and IRHvac case sensitive parameter regression introduced with version 5.8.0 (#993)
|
|
|
|
|
* Fix pressure calculation for some BMP versions regression introduced with version 5.8.0i (#974)
|
|
|
|
|
* Fix Domoticz Dimmer set to same level not powering on (#945)
|
|
|
|
|
* Fix Blocked Loop when erasing large flash using command reset 2 (#1002)
|
|
|
|
|
* Fix relay power control when light power control is also configured as regression from 5.8.0 (#1016)
|
|
|
|
|
* Fix Mqtt server mDNS lookup only when MqttHost name is empty (#1026)
|
2017-09-26 14:10:58 +01:00
|
|
|
* Add debug information to MQTT subscribe
|
2017-09-23 10:12:16 +01:00
|
|
|
* Add translations to I2Cscan
|
|
|
|
|
* Add translation to BH1750 unit lx
|
2017-11-03 17:07:25 +00:00
|
|
|
* Add light scheme options (Color cycle Up, Down, Random) and moving WS2812 schemes up by 3
|
|
|
|
|
* Add Domoticz counter sensor to IrReceive representing Received IR Protocol and Data
|
|
|
|
|
* Add option 0 to MqttHost to allow empty Mqtt host name
|
|
|
|
|
* Add support for Arilux AL-LC01 RGB Led controller (#370)
|
|
|
|
|
* Add esp8266 de-blocking to PubSubClient library (#790)
|
|
|
|
|
* Add Domoticz sensors for Voltage and Current (#903)
|
|
|
|
|
* Add platformio OTA upload support (#928, #934)
|
|
|
|
|
* Add warning to webpage when USE_MINIMAL is selected (#929)
|
|
|
|
|
* Add smoother movement of hour hand in WS2812 led clock (#936)
|
|
|
|
|
* Add support for Magic Home RGBW and some Arilux Led controllers (#940)
|
|
|
|
|
* Add command SetOption15 0 (default) for command PWM control or SetOption15 1 for commands Color/Dimmer control to PWM RGB(CW) leds (#941)
|
|
|
|
|
* Add Domoticz counter sensor to Sonoff Bridge representing Received RF code (#943)
|
|
|
|
|
* Add support for Luani HVIO board (https://luani.de/projekte/esp8266-hvio/) (#953)
|
|
|
|
|
* Add PWM initialization after restart (#955)
|
|
|
|
|
* Add IR Receiver support. Disable in user_config.h (#956)
|
|
|
|
|
* Add support for inverted PWM (#960)
|
|
|
|
|
* Add Sea level pressure calculation and Provide command Altitude (#974)
|
|
|
|
|
* Add support for up to 8 relays (#995)
|
|
|
|
|
* Add commands RfSync, RfLow, RfHigh, RfHost and RfCode to allow sending custom RF codes (#1001)
|
|
|
|
|
* Add retain to ENERGY messages controlled by command SensorRetain (#1013)
|
|
|
|
|
* Add commands Color2, Color3, Color4, Width2, Width3, Width4 and SetOption16 to set Ws2812 Clock parameters (#1019)
|
|
|
|
|
* Add German language file (#1022)
|
|
|
|
|
* Add support for connecting to MQTT brokers without userid and/or password (#1023)
|
|
|
|
|
* Add support for esp8266 core v2.4.0-rc2 (#1024)
|
|
|
|
|
* Add commands PwmRange 1,255..1023 and PwmFrequency 1,100..4000 (#1025)
|
|
|
|
|
* Add Polish language file (#1044, #1047)
|
|
|
|
|
* Add support for KMC 70011 Power Monitoring Smart Plug (#1045)
|
|
|
|
|
* Add support for VEML6070 I2C Ultra Violet level sensor (#1053)
|
|
|
|
|
* Add light turn Off Fade (#925)
|
|
|
|
|
* Add IrSend command option Panasonic as IrSend {"Protocol":"Panasonic", "Bits":16388, "Data":<Panasonic data>}
|
|
|
|
|
* where 16388 is 0x4004 hexadecimal (#1014)
|
|
|
|
|
* Add retry counter to DHT11/21/22 sensors (#1082)
|
2017-09-16 17:19:15 +01:00
|
|
|
*
|
2017-09-23 10:12:16 +01:00
|
|
|
* 5.8.0 20170918
|
|
|
|
|
* Remove the need for NeoPixelBus library for Hue support
|
|
|
|
|
* Consolidate WS2812 into Sonoff Led for flexible future led strip library changes
|
2017-09-16 16:34:03 +01:00
|
|
|
* Invert WS2812 fade speed to align with Sonoff led (Speed 1 = fast, Speed 8 = slow)
|
|
|
|
|
* Remove upper case MQTT receive buffer
|
2017-09-14 14:35:38 +01:00
|
|
|
* Reduce code and string length for output of commands Modules and GPIOs
|
2017-09-14 13:20:27 +01:00
|
|
|
* Add Sonoff SC debug information
|
|
|
|
|
* Change syslog service
|
2017-09-13 13:19:34 +01:00
|
|
|
* Removed webserver syslog disable as now no longer needed
|
2017-09-14 13:20:27 +01:00
|
|
|
* Increased default MQTT message size from 368 to 405 bytes while keeping MQTT_MAX_PACKET_SIZE = 512 (because we can)
|
2017-09-13 13:19:34 +01:00
|
|
|
* Fix MQTT Offline or Remove MQTT retained topic code
|
2017-09-10 14:51:44 +01:00
|
|
|
* Fix Domoticz loop when Emulation is selected
|
2017-09-23 10:12:16 +01:00
|
|
|
* Add blink to WS2812 and Sonoff Led (#643)
|
|
|
|
|
* Add option WIFI_WAIT (5) to command WifiConfig to allow connection retry to same AP without restart or update flash (#772, #869)
|
2017-09-10 14:51:44 +01:00
|
|
|
* Add support for Witty Cloud (#794)
|
2017-09-23 10:12:16 +01:00
|
|
|
* Add GPIO14 to Sonoff Dual (#797, #839)
|
2017-09-10 14:51:44 +01:00
|
|
|
* Add support for Yunshan Wifi Relay (#802)
|
|
|
|
|
* Add GPIO16 input pulldown (#827)
|
2017-09-23 10:12:16 +01:00
|
|
|
* Add timeout to DHT and DS18B20 sensors (#852)
|
|
|
|
|
* Fix watchdog timeout caused by lack of stack space by moving to heap (#853)
|
|
|
|
|
* Allow LogPort and MqttPort up to 65535 and add LogPort tot Status 3 (#859)
|
|
|
|
|
* Allow command SwitchTopic in group mode (#861)
|
|
|
|
|
* Allow command SwitchMode if no switches are defined (#861)
|
|
|
|
|
* Add optional dimmer parameter to command Wakeup for WS2812, AiLight, Sonoff B1, Led and BN-SZ01 (#867)
|
|
|
|
|
* Fix basic On, Off, Toggle, Blink and BlinkOff commands when other language is selected (#874)
|
2017-09-10 14:51:44 +01:00
|
|
|
*
|
|
|
|
|
* 5.7.1 20170909
|
2017-09-08 11:57:08 +01:00
|
|
|
* Remove leading spaces from MQTT data
|
|
|
|
|
* Fix webconsole special character entry
|
|
|
|
|
* Allow # as prefix for color value
|
2017-09-09 17:46:29 +01:00
|
|
|
* Fix Alexa detection and Hue App Update Request (#698, #854)
|
2017-09-08 11:57:08 +01:00
|
|
|
*
|
|
|
|
|
* 5.7.0 20170907
|
2017-09-07 17:53:59 +01:00
|
|
|
* Shrink module configuration webpage
|
|
|
|
|
* Fix settings order during startup to allow for displaying debug messages
|
2017-09-06 16:37:41 +01:00
|
|
|
* Fix some string length issues
|
|
|
|
|
* Add more string length tests by using strncpy
|
2017-09-07 17:53:59 +01:00
|
|
|
* Add Ai-Thinker RGBW led (AiLight)
|
|
|
|
|
* Add Power check and add PulseTime to power check at startup (#526)
|
|
|
|
|
* Add Supla Espablo support (#755)
|
|
|
|
|
* Add more precision to Sonoff Pow period and power results using command WattRes 0|1 (#759)
|
2017-09-02 13:37:02 +01:00
|
|
|
* Add basic internationalization and localization (#763)
|
2017-08-24 10:09:52 +01:00
|
|
|
* Add more Sonoff Pow range checking (#772)
|
2017-09-07 17:53:59 +01:00
|
|
|
* Fix invalid JSON (#786, #822)
|
|
|
|
|
* Add duplicate check to received RF signal within 2 seconds for Sonoff Bridge (#810)
|
2017-08-19 15:29:51 +01:00
|
|
|
*
|
|
|
|
|
* 5.6.1 20170818
|
2017-08-18 17:04:49 +01:00
|
|
|
* Change module list order in webpage
|
|
|
|
|
* Fix Sonoff T1 1CH and 2CH configuration (#751)
|
|
|
|
|
*
|
|
|
|
|
* 5.6.0 20170818
|
2017-08-10 15:21:31 +01:00
|
|
|
* Fix Sonoff Pow intermittent exception 0
|
|
|
|
|
* Change Sonoff Pow sending Domoticz telemetry data only
|
2017-08-18 13:52:57 +01:00
|
|
|
* Add Ai-Thinker RGBW led (AiLight) (experimental)
|
|
|
|
|
* Add NeoPixelBus library to Sonoff Led for Hue support
|
|
|
|
|
* Add user configurable GPIO4 and GPIO5 to module Sonoff Bridge
|
2017-08-16 16:05:36 +01:00
|
|
|
* Add Sonoff B1 RGBCW led support with command Color RRGGBBCCWW (#676)
|
|
|
|
|
* Add command CT 152..500 to Sonoff Led and Sonoff B1 to control Color Temperature
|
|
|
|
|
* Add Cold-Warm slider to web page for Sonoff Led and Sonoff B1
|
|
|
|
|
* Add CT parameter to Hue
|
2017-08-16 21:56:32 +01:00
|
|
|
* Add Sonoff T1 support (#582)
|
2017-08-18 13:52:57 +01:00
|
|
|
* Add AnalogInput0 if configured as Analog Input to webpage (#697, #746)
|
2017-08-18 11:55:08 +01:00
|
|
|
* Add command SetOption14 0|1 to enable interlock mode (#719, #721)
|
2017-08-18 13:52:57 +01:00
|
|
|
* Fix Mitsubishi HVAC IR power controll (#740)
|
2017-08-10 08:12:18 +01:00
|
|
|
*
|
|
|
|
|
* 5.5.2 20170808
|
2017-08-08 15:31:43 +01:00
|
|
|
* Extent max number of WS2812 pixels from 256 to 512 (#667)
|
|
|
|
|
* Add OTA handling if server responds with no update available (#695)
|
|
|
|
|
* Removed undocumented command FlashMode (#696)
|
|
|
|
|
* Fix compile time error message due to increased message buffer size (#703)
|
|
|
|
|
*
|
|
|
|
|
* 5.5.1 20170805
|
2017-08-05 14:11:50 +01:00
|
|
|
* Fix Sonoff Rf Bridge issues
|
|
|
|
|
* Add Sonoff RF Bridge MQTT messages on received and learned RF signal
|
|
|
|
|
* Add command VoltRes 0|1 to select voltage resolution to 0.1 V (#654)
|
|
|
|
|
* Add averaging to Analog input (#686)
|
|
|
|
|
* Add Energy tele data on Sonoff Pow Threshold change (#688)
|
|
|
|
|
* Fix inconsistent property names in Messages (#690)
|
|
|
|
|
*
|
|
|
|
|
* 5.5.0 20170730
|
2017-07-30 16:55:37 +01:00
|
|
|
* Reduce code space by removing the following commands as they are replaced by SetOption alternatives:
|
|
|
|
|
* SaveState = SetOption0
|
|
|
|
|
* ButtonRestrict = SetOption1
|
|
|
|
|
* Units = SetOption2
|
|
|
|
|
* MQTT = SetOption3
|
|
|
|
|
* MQTTResponse = SetOption4
|
|
|
|
|
* TempUnit = SetOption8
|
|
|
|
|
* Smoothing WS2812 animation poll, invert fade speed and max allowed wakeup time down to 3000 seconds
|
|
|
|
|
* Fix initial button press detection
|
|
|
|
|
* Add support for Sonoff RF Bridge 433 using command RfKey
|
|
|
|
|
* Fix regression from 5.0.7 by increasing message buffer size from 360 to 368 to accomodate 4 x DS18x20 sensors (#637)
|
|
|
|
|
* Add GroupTopic to Topic test when using ButtonTopic/SwitchTopic to send either ON/OFF or TOGGLE (#642)
|
|
|
|
|
* Adjust HLW calibration limits to accomodate HuaFan device and add commands HlwPSet, HlwUSet and HlwISet (#654)
|
|
|
|
|
*
|
|
|
|
|
* 5.4.0 20170725
|
2017-07-25 17:05:47 +01:00
|
|
|
* Fix command reset regression introduced in 5.2.0
|
|
|
|
|
* Increase polling from 0.1 second to 0.05 second
|
|
|
|
|
* Add multipress to all buttons
|
|
|
|
|
* Fix button 1 double press behaviour on multi relay devices
|
|
|
|
|
* Add support for Hua Fan Smart Socket (#479)
|
|
|
|
|
* Add support for Sonoff 4ch Pro (#565)
|
2017-09-02 13:37:02 +01:00
|
|
|
* Add command SetOption13 1 to allow immediate action on single button press
|
2017-07-25 17:05:47 +01:00
|
|
|
* (disables multipress, hold and unrestricted commands) (#587)
|
|
|
|
|
*
|
|
|
|
|
* 5.3.0 20170715
|
2017-07-15 14:07:30 +01:00
|
|
|
* Major Hue rewrite which might introduce Alexa problems. If so, initiate an issue
|
|
|
|
|
* Add support for Sonoff Led and BN-SZ01 Ceiling Led brightness control to Hue
|
|
|
|
|
* Fix Sonoff Led Power, Dimmer and Color MQTT response (#176)
|
|
|
|
|
* Add commands Delay and Backlog to allow multiple commands at once separated by ";" (#593)
|
|
|
|
|
* Use default flashmode DOUT to solve restart hangs on esp8285 chips (#453, #598)
|
|
|
|
|
* Change Web console column width from 99 to 300 (#599)
|
|
|
|
|
*
|
|
|
|
|
* 5.2.4 20170703
|
2017-07-03 10:45:15 +01:00
|
|
|
* Removed flash mode update after selecting different module solving esp8285 related problems
|
|
|
|
|
* Add device type flag to sonoff_template.ino
|
2017-07-03 10:52:15 +01:00
|
|
|
* Change Sonoff Led Wakeup and add support for Sonoff BN-SZ01 Led (#567)
|
2017-07-03 10:45:15 +01:00
|
|
|
*
|
|
|
|
|
* 5.2.3 20170630
|
2017-06-30 16:54:19 +01:00
|
|
|
* Change Sonoff Led color conversion code
|
|
|
|
|
* Fix SetOption12 handling
|
|
|
|
|
* Simplify auto configuration upgrade
|
|
|
|
|
* Add option Upgrade <version_number> to only upgrade to any higher version (Old PR #213)
|
|
|
|
|
* Change FallbackTopic to cmnd/<MQTTClient>/<command> <parameter> bypassing FullTopic and Prefix (#538)
|
|
|
|
|
*
|
|
|
|
|
* 5.2.2 20170625
|
2017-06-25 22:01:41 +01:00
|
|
|
* Add configuration SaveAddress to Status 1 and Information Page
|
|
|
|
|
* Change Sonoff Led Color conversion from AtoH to strtol
|
|
|
|
|
* Fix possible wrong uploads due to configuration overwrites (#542)
|
|
|
|
|
* Fix payload negative numbers (#547)
|
|
|
|
|
*
|
|
|
|
|
* 5.2.1 20170622
|
2017-06-22 21:00:09 +01:00
|
|
|
* Fix Restore Configuration in case of lower version
|
2017-09-02 13:37:02 +01:00
|
|
|
* Revert auto configuration upgrade allowing easy upgrade which was removed in version 5.2.0
|
2017-06-22 21:00:09 +01:00
|
|
|
* Fix config auto upgrade from versions below version 4.1.1 (#530)
|
|
|
|
|
*
|
|
|
|
|
* 5.2.0 20170619
|
2017-06-19 21:54:49 +01:00
|
|
|
* Add command SetOption12 1 to disable newly released configuration flash rotate to reduce flash wear
|
|
|
|
|
* Fix command CounterDebounce by removing test for active GPIO (#524)
|
|
|
|
|
* Add command SetOption33 1..250 to allow user configure POW Max_Power_Retry count (#525)
|
|
|
|
|
*
|
|
|
|
|
* 5.1.7 20170616
|
2017-06-16 13:33:49 +01:00
|
|
|
* Prep removal of SetOptions alternatives
|
|
|
|
|
* Restore webpage upgrade error messages removed in 5.1.5
|
|
|
|
|
* Add hold button functionality to buttons 2 to 4
|
|
|
|
|
* Add command SetOption32 1..100 to set Key Hold Time from 0.1 seconds to 10 seconds (#200)
|
|
|
|
|
* Allow slashes in Topic, GroupTopic, ButtonTopic and SwitchTopic (#507)
|
|
|
|
|
* Changed webpage form actions from post to get and use relative path url (#434, #522)
|
|
|
|
|
*
|
|
|
|
|
* 5.1.6 20170606
|
2017-06-06 22:23:23 +01:00
|
|
|
* Shrink code
|
|
|
|
|
* Removed online configuration of Domoticz In and Domoticz Out MQTT strings
|
|
|
|
|
* Removed commands DomoticzInTopic and DomoticzOutTopic
|
|
|
|
|
* Add define KEY_HOLD_TIME to configure button hold threshold before sending MQTT Hold message
|
|
|
|
|
* Add command StateText4 to configure button MQTT Hold text (= MQTT_CMND_HOLD)
|
|
|
|
|
* Add command SetOption11 0|1 to swap pushbutton single and double press functionality (#200)
|
|
|
|
|
* Add command SwitchMode<x> 5 (PUSHBUTTONHOLD) and 6 (PUSHBUTTONHOLD_INV) (#489)
|
|
|
|
|
*
|
|
|
|
|
* 5.1.5 20170604
|
2017-06-04 16:40:27 +01:00
|
|
|
* Shrink code in preparation to ESP8266-Arduino 2.4.0-rc1
|
|
|
|
|
* Add effect parameter to HUE Device (#464)
|
|
|
|
|
*
|
|
|
|
|
* 5.1.4 20170601
|
2017-06-01 16:37:30 +01:00
|
|
|
* Removed pre-compiled versions from repository as they are available within the release
|
|
|
|
|
* Changed HUE Device type to color supporting version (#464)
|
|
|
|
|
* Fix compile error when BE_MINIMAL is selected (#467, #476)
|
|
|
|
|
* Add multiple compiled versions to release using updated Travis script and platformio.ini (#467)
|
2017-06-04 16:40:27 +01:00
|
|
|
*
|
2017-06-01 16:37:30 +01:00
|
|
|
* 5.1.3 20170520
|
2017-05-20 13:03:34 +01:00
|
|
|
* Add Domoticz Counter
|
|
|
|
|
*
|
|
|
|
|
* 5.1.2 20170519
|
2017-05-19 15:09:25 +01:00
|
|
|
* Fix Counter/Timer JSON message and update Counter/Timer on webpage
|
|
|
|
|
* Fix WS2812 Domoticz related regression issues
|
2017-06-06 22:23:23 +01:00
|
|
|
*
|
2017-05-19 15:09:25 +01:00
|
|
|
* 5.1.1 20170517
|
2017-05-17 21:49:22 +01:00
|
|
|
* Allow command FullTopic in group mode
|
|
|
|
|
* Prepare for more use of RTC memory
|
|
|
|
|
* Add independant WS2812 led string power control (#386, #390)
|
|
|
|
|
* Add command Counter<x> to control up to four GPIO falling edge interrupt counters or timers (#459)
|
|
|
|
|
* Add command CounterType<x> to select between pulse counting or pulse timing
|
|
|
|
|
* Add command CounterDebounce to select global counter debounce time in mSec
|
|
|
|
|
*
|
|
|
|
|
* 5.1.0 20170513
|
2017-05-13 12:02:10 +01:00
|
|
|
* Fix Offline/Removal of retained topic when FullTopic is changed
|
2017-05-13 12:09:54 +01:00
|
|
|
* Add FullTopic to MQTT Configuration and Information web pages
|
2017-05-13 12:04:28 +01:00
|
|
|
* Add license model GPLv3 (#188)
|
2017-05-13 12:02:10 +01:00
|
|
|
*
|
|
|
|
|
* 5.0.7 20170511
|
2017-05-11 16:47:34 +01:00
|
|
|
* Fix possible exception 28 on empty command
|
|
|
|
|
* Add command SetOption0 as replacement for SaveState
|
|
|
|
|
* Add command SetOption1 as replacement for ButtonRestrict
|
|
|
|
|
* Add command SetOption2 as replacement for Units
|
|
|
|
|
* Add command SetOption4 as replacement for MqttResponse
|
|
|
|
|
* Add command SetOption8 as replacement for TempUnit
|
|
|
|
|
* Add command SetOption10 On|Off to select between Offline or Removing previous retained topic (#417, #436)
|
|
|
|
|
*
|
|
|
|
|
* 5.0.6 20170510
|
|
|
|
|
* Remove hyphen in case of a single DHT sensor connected (#427)
|
2017-05-10 13:19:36 +01:00
|
|
|
* Add command MqttRetry <seconds> to change default MQTT reconnect retry timer from minimal 10 seconds (#429)
|
|
|
|
|
*
|
|
|
|
|
* 5.0.5 20170508
|
2017-09-02 13:37:02 +01:00
|
|
|
* Add command FullTopic with tokens %topic% (replaced by command Topic value) and
|
2017-05-08 12:21:45 +01:00
|
|
|
* %prefix% (replaced by command Prefix<x> values) for more flexible topic definitions (#244)
|
|
|
|
|
* See wiki > MQTT Features https://github.com/arendst/Sonoff-Tasmota/wiki/MQTT-Features for more information
|
|
|
|
|
*
|
|
|
|
|
* 5.0.4 20170505
|
2017-05-05 16:57:05 +01:00
|
|
|
* Add Sonoff Pow Energy Total up to 40 MWh
|
|
|
|
|
* Add command EnergyReset 1|2|3 to reset Energy counters (#406)
|
|
|
|
|
* Fix Domoticz Energy logging (#411)
|
|
|
|
|
* Add command PowerOnState 4 to keep relay always on and disabling all power control (#418)
|
|
|
|
|
*
|
|
|
|
|
* 5.0.3 20170504
|
2017-05-04 12:58:26 +01:00
|
|
|
* Add command SensorRetain on|off to enable retaining of mqtt message tele/sonoff/SENSOR (#74)
|
|
|
|
|
* Change WifiConfig timeout from 60 seconds to 180 seconds (#212)
|
|
|
|
|
* Change Sonoff Touch command Ledstate functionality by turning led on if power is off (#214)
|
|
|
|
|
* Add 4 seconds delay after power on before enabling button to workaround Wemos D1 mini RTS circuit (#380)
|
|
|
|
|
*
|
|
|
|
|
* 5.0.2 20170503
|
2017-05-03 17:19:13 +01:00
|
|
|
* Reset SaveData, SaveState and MqttResponse to default values due to rearranging settings
|
2017-05-03 17:21:24 +01:00
|
|
|
* Moved some settings to flag area
|
2017-05-03 17:19:13 +01:00
|
|
|
* Add command TempUnit Celsius|Fahrenheit for selecting Celsius or Fahrenheit (#347)
|
|
|
|
|
* Add command TempRes 0..3 for selecting Temperature Resolution (#347)
|
|
|
|
|
* Add command HumRes 0..3 for selecting Humidity Resolution (#347)
|
|
|
|
|
* Add command PressRes 0..3 for selecting Pressure Resolution (#347)
|
|
|
|
|
* Add command EnergyRes 0..5 for selecting Energy Resolution (#347)
|
2017-05-03 17:21:24 +01:00
|
|
|
* Add "TempUnit":"C|F" to sensor JSON output (#347)
|
2017-05-03 17:19:13 +01:00
|
|
|
* Add support for up to three DHT type sensors each using a different GPIO (#339, #404)
|
|
|
|
|
*
|
|
|
|
|
* 5.0.1 20170429
|
2017-04-29 13:40:53 +01:00
|
|
|
* Adjust Sonoff SC messages to prepare for display feature
|
|
|
|
|
* Move static data from RAM to Flash
|
|
|
|
|
* Fix PowerOnState for some devices not reporting "Power on" state (#284, #380, #383)
|
|
|
|
|
*
|
|
|
|
|
* 5.0.0 20170425
|
2017-04-25 17:24:42 +01:00
|
|
|
* Memory status message update
|
|
|
|
|
* Fix setting migration to better preserve settings during move (#382)
|
|
|
|
|
* Best practice is first doing a Backup Configuration before installing version 5.0.0
|
|
|
|
|
* Reset save count after setting move
|
|
|
|
|
* Start using new linker script without SPIFFS
|
|
|
|
|
*
|
|
|
|
|
* 4.2.0 20170424
|
2017-04-24 17:25:53 +01:00
|
|
|
* Prepare for SPIFFS removal by moving settings to EEPROM area
|
|
|
|
|
* Fix compilation error when webserver is disabled (#378)
|
|
|
|
|
*
|
|
|
|
|
* 4.1.3 20170410
|
2017-04-10 16:25:31 +01:00
|
|
|
* Add user configuarble GPIO to module S20 Socket and Slampher
|
|
|
|
|
* Add support for Sonoff SC (#112)
|
|
|
|
|
* Set PWM frequency from 1000Hz to 910Hz as used on iTead Sonoff Led firmware (#122)
|
|
|
|
|
* Set Sonoff Led unconfigured floating outputs to 0 to reduce exceptions due to power supply instabilities (#122)
|
|
|
|
|
* Add Access Point Mac Address to Status 11 and Telemetry (#329)
|
|
|
|
|
* Fix DS18B20 negative temperature readings (#334)
|
|
|
|
|
*
|
|
|
|
|
* 4.1.2 20170403
|
2017-04-03 15:38:15 +01:00
|
|
|
* Rename Unrecognised command to Unknown command
|
|
|
|
|
* Remove all command lists
|
|
|
|
|
* Remove command SmartConfig (superseded by WifiConfig)
|
|
|
|
|
* Fix boot loop when selecting module Sonoff 4CH or Sonoff Touch on non ESP8285 hardware
|
2017-04-03 15:51:07 +01:00
|
|
|
* Add optional support for Toshiba and Mitsubishi HVAC IR control (needs updated IRremote8266 library) (#83, #257)
|
2017-04-03 15:38:15 +01:00
|
|
|
* Add all configured switches to Domoticz Configuration web page (#305)
|
|
|
|
|
* Fix compile error when selecting WS2812 DMA (#313)
|
|
|
|
|
*
|
|
|
|
|
* 4.1.1 20170329
|
2017-03-29 17:42:05 +01:00
|
|
|
* Fix default Telemetry for command Prefix3
|
|
|
|
|
* Fix webserver Module parameters for disabled select
|
|
|
|
|
* Fix sensor status for enabled switches
|
|
|
|
|
* Remove Light as alternative for Power (save code space)
|
|
|
|
|
* Remove migration option from pre V3 (code cleanup)
|
|
|
|
|
* Remove unofficial SPIFFS support (code cleanup)
|
|
|
|
|
* Remove command list when unknown command is entered (save code space)
|
|
|
|
|
* Rename Status11 json from StatusPWR to unique StatusSTS
|
|
|
|
|
* Rename command Gateway to IPAddres2, Subnetmask to IPAddress3 and DnsServer to IPAddress4 (save code space)
|
|
|
|
|
* Add Command MqttResponse to select either command or RESULT topic as response (#258)
|
|
|
|
|
* Add command StateText1 to StateText3 to assign MQTT_STATUS_OFF, MQTT_STATUS_ON and MQTT_CMND_TOGGLE respectively (#286)
|
|
|
|
|
* Remove restart after IPAddress changes (#292)
|
|
|
|
|
* Add support for MAX31850 in xsns_ds18x20.ino (#295)
|
|
|
|
|
* Fix possible uptime update misses (#302)
|
2017-09-02 13:37:02 +01:00
|
|
|
*
|
2017-03-29 17:42:05 +01:00
|
|
|
* 4.1.0 20170325
|
2017-03-25 16:24:11 +00:00
|
|
|
* Change static IP addresses in user_config.h from list (using commas) to string (using dots)
|
|
|
|
|
* Unify display result of commands Modules, Module and Gpios
|
|
|
|
|
* Rewrite Module selection web page to bring size down from 18651 to 4319 bytes (!) (#234, #240)
|
|
|
|
|
* Add basic support for (Lixada) H801 RGBWW controller (#252)
|
|
|
|
|
* Add command Prefix1 to Prefix3 to assign SUB_PREFIX, PUB_PREFIX and PUB_PREFIX2 respectively (#255)
|
|
|
|
|
* Add static ip addresses to flash (#262)
|
|
|
|
|
* Add commands IpAddress, Gateway, Subnetmask and DnsServer to select static ip addresses (#273)
|
|
|
|
|
*
|
|
|
|
|
* 4.0.8 20170321
|
2017-03-21 15:17:28 +00:00
|
|
|
* Fix entering non-numeric webpassword
|
|
|
|
|
* Force selection between TLS or Webserver due to memory restraint (#240)
|
|
|
|
|
* Allow entering empty string using "0" for selected commands (#242)
|
|
|
|
|
* Fix exception when posting commands to web console containing % (#250)
|
|
|
|
|
*
|
|
|
|
|
* 4.0.7 20170319
|
2017-03-19 17:19:08 +00:00
|
|
|
* Increased Sonoff Led PWM frequency from 432 to 1000
|
|
|
|
|
* Fix possible watch dog reboot after changing module type on web page
|
|
|
|
|
* Fix reporting of GPIO usage from web page
|
|
|
|
|
* Fix Sonoff Led blank during firmware upgrade
|
|
|
|
|
* Fix Sonoff Led flicker and possible flash corruption by using latest Arduino-esp8266 versions
|
|
|
|
|
* of pwm core files included in sonoff library (#211)
|
|
|
|
|
* Add PWM output control with commands PWM1 to PWM5 using user selectable GPIOs (#211)
|
|
|
|
|
* Fix exceptions due to low values of commands HlwPCal (10000), HlwUCal (1000) and HlwICal (2500) (#223)
|
|
|
|
|
* Add Switch state to sensor status (#227, #233)
|
|
|
|
|
* Add user configuarble GPIO to module Sonoff Touch (#228)
|
|
|
|
|
* Add define WEB_PORT to user_config.h to change default web server port from 80 (#232)
|
|
|
|
|
* Fix failed Ota Firmware upgrade started from Web page (#235)
|
|
|
|
|
*
|
|
|
|
|
* 4.0.6 20170316
|
2017-03-16 15:23:11 +00:00
|
|
|
* Fix to better find device by Wifi hostname
|
|
|
|
|
* Fix compile error when some I2C devices are disabled
|
|
|
|
|
* Add (experimental) support for SHT1X emulating I2C (#97)
|
|
|
|
|
* Add ADC to ElectroDragon (#203)
|
|
|
|
|
* Add support for Sonoff Dev (#206)
|
|
|
|
|
*
|
|
|
|
|
* 4.0.5 20170314
|
2017-03-14 17:03:25 +00:00
|
|
|
* Add command Status 11 to show power status with Vcc if define USE_ADC_VCC is enabled (default)
|
|
|
|
|
* Add ADC input to Sonoff SV and Wemos D1 mini - Needs recompile with define USE_ADC_VCC disabled (#137)
|
|
|
|
|
* Add MQTT host:port to timeout message (#199)
|
|
|
|
|
*
|
|
|
|
|
* 4.0.4 20170312
|
2017-03-12 17:36:33 +00:00
|
|
|
* Add pulse timers for up to 4 relays (#106)
|
|
|
|
|
* Fix Sonoff Led power state when dimmer or color is 0 (#176)
|
|
|
|
|
* Add command NtpServer<x> to configure up to three NTP servers (#177)
|
|
|
|
|
* Delete module User Test as module Wemos D1 mini has same/more user configurable GPIO (#178)
|
|
|
|
|
* Add more user configurable GPIO to module ElectroDragon (#183)
|
|
|
|
|
*
|
|
|
|
|
* 4.0.3 20170309
|
2017-03-09 16:48:04 +00:00
|
|
|
* Renamed Module NodeMCU to WeMos D1 mini
|
|
|
|
|
* Add GPIO1 as user option to some modules
|
|
|
|
|
* Add Buttons, Relays and Leds to user configurable options (#159)
|
|
|
|
|
* Add description on Module parameters web page to some well known GPIOs (#107, #171)
|
2017-03-12 17:36:33 +00:00
|
|
|
*
|
2017-03-09 16:48:04 +00:00
|
|
|
* 4.0.2 20170308
|
2017-03-08 15:20:45 +00:00
|
|
|
* Restore correct seriallog level after Serial logging was disabled
|
|
|
|
|
* Add simple dimmer slider to Sonoff Led web page
|
|
|
|
|
* Reduced root webpage size by 31%
|
|
|
|
|
* Expand Status 2 with Build date/time and core version
|
|
|
|
|
* Fix webserver redirection when not in WifiManager mode (#156)
|
|
|
|
|
* Add command ButtonRestrict On/Off to restrict access to button hold and button multi press options above 2 (#161)
|
|
|
|
|
* Fix DS18S20 negative temperature readings (#165)
|
|
|
|
|
* Fix crlf compilation error due to bad syntax (#144, #167)
|
|
|
|
|
*
|
|
|
|
|
* 4.0.1 20170305
|
2017-03-05 14:07:30 +00:00
|
|
|
* Fix char default sizes and set MESSZ to 360 (#143)
|
|
|
|
|
* Fix SerialLog setting status
|
|
|
|
|
* Disable syslog when emulation is active
|
|
|
|
|
* Add DS18B20 web page display refresh
|
|
|
|
|
*
|
|
|
|
|
* 4.0.0 20170303
|
2017-03-03 11:35:23 +00:00
|
|
|
* Add define to remove config migration code for versions below 3.0 (See Wiki-Upgrade-Migration path)
|
|
|
|
|
* Free memory by switching from String to char[]
|
|
|
|
|
* Raised Sonoff Led PWM frequency from 200Hz to 432Hz in search of stability (hardware watchdog timeouts) (#122)
|
|
|
|
|
* Increase message size and suggested minimum MQTT_MAX_PACKET_SIZE to 512 (#114, #124)
|
|
|
|
|
* Remove runtime warning message regarding MQTT_MAX_PACKET_SIZE too small as it is now moved to compile time (#124)
|
|
|
|
|
* Fix possible panics with web console and http commands while UDP syslog is active (#127)
|
|
|
|
|
* Add optional static IP address (#129)
|
|
|
|
|
* Add define ENERGY_RESOLUTION in user_config.h to allow user control over precision (#136)
|
|
|
|
|
*
|
|
|
|
|
* 3.9.22 20170228
|
2017-02-28 15:01:48 +00:00
|
|
|
* Update web console
|
|
|
|
|
* Fix Status 4 JSON message
|
|
|
|
|
* Add Exception info during restart if available
|
|
|
|
|
* Add osWatch service to detect loop hangs that might happen during (OTA) upgrades
|
|
|
|
|
* Add WiOn support for relay and switch only (#82, #102)
|
|
|
|
|
* Allow for user specified relay count up to four in sonoff_template.h (#109)
|
|
|
|
|
* Add support for HTU21 compatible I2C sensors SI7013, SI7020 and SI7021 (#118)
|
|
|
|
|
* Add NodeMCU or Wemos configuration option (#119)
|
|
|
|
|
*
|
|
|
|
|
* 3.9.21 20170224
|
2017-02-24 17:17:48 +00:00
|
|
|
* Add ajax to web root page and web console (#79)
|
|
|
|
|
* Add commands SwitchMode1..4 and enable user switches 2, 3 and 4 (#84, #88)
|
|
|
|
|
* Fix MQTT upgrade when webserver is active
|
|
|
|
|
*
|
|
|
|
|
* 3.9.20 20170221
|
2017-02-21 17:14:33 +00:00
|
|
|
* Add minimal basic authentication to Web Admin mode (#87)
|
|
|
|
|
* Fix Hue and add HSB support (#89)
|
2017-09-02 13:37:02 +01:00
|
|
|
*
|
2017-02-21 17:14:33 +00:00
|
|
|
* 3.9.19 20170219
|
2017-02-19 16:49:17 +00:00
|
|
|
* Sonoff Led: Made GPIO04, 05 and 15 available for user
|
|
|
|
|
* Sonoff Led: Add commands Fade, Speed, WakupDuration, Wakeup and LedTable
|
|
|
|
|
*
|
|
|
|
|
* 3.9.18 20170218
|
2017-02-18 17:08:55 +00:00
|
|
|
* Fix ledstate 0 to turn off led
|
|
|
|
|
* Fix Sonoff Led dimmer range (#16)
|
|
|
|
|
* Change Sonoff Led command Dimmer to act on both cold and warm color
|
|
|
|
|
* Add Sonoff Led command Color CCWW where CCWW are hexadecimal values fro 00 - FF
|
2017-09-02 13:37:02 +01:00
|
|
|
* Reduce Sonoff Led flickering by disabling interrupts during flash save and disabling
|
2017-02-18 17:08:55 +00:00
|
|
|
* Led during OTA upgrade and Web upload (#16)
|
|
|
|
|
*
|
|
|
|
|
* 3.9.17 20170217
|
2017-02-17 16:18:41 +00:00
|
|
|
* Fix possible ArduinoJSON related memory fragmentation
|
|
|
|
|
* Changed console logging using less memory
|
|
|
|
|
* Add GPIO04 as user selectable for Sonoff Dual (#75)
|
|
|
|
|
*
|
|
|
|
|
* 3.9.16 20170214
|
2017-02-14 13:27:08 +00:00
|
|
|
* Update latching relay handler
|
|
|
|
|
* Add support for IR led using IRremoteESP8266 library (#59)
|
|
|
|
|
* Add Hue argument passing using ArduinoJSON library (#59)
|
|
|
|
|
*
|
|
|
|
|
* 3.9.15 20170213
|
2017-02-13 16:25:46 +00:00
|
|
|
* Change JSON float values from string to number according to http://json.org (#56)
|
|
|
|
|
* Add support for exs latched relay module https://ex-store.de/ESP8266-WiFi-Relay-V31 (#58)
|
|
|
|
|
* Add support for inverted relays
|
|
|
|
|
* Changed MAX_LOG_LINES from 70 to 60 to preserve memory
|
|
|
|
|
*
|
|
|
|
|
* 3.9.14 20170211
|
2017-02-11 14:06:23 +00:00
|
|
|
* Add False and True as alternatives for 0/Off and 1/On (#49)
|
|
|
|
|
* Fix Status10 JSON format (#52)
|
|
|
|
|
* Fix DS18x20 using OneWire library (#53)
|
|
|
|
|
*
|
|
|
|
|
* 3.9.13 20170210
|
2017-02-13 16:25:46 +00:00
|
|
|
* Add FlashChipMode to Status 4
|
2017-02-10 16:03:34 +00:00
|
|
|
* Removed redundant DHT2 option and code
|
|
|
|
|
* Add Sonoff SV GPIO pin 05 configuration (#40)
|
|
|
|
|
* Add configuration file backup and restore via web page
|
|
|
|
|
* Fix latency due to light_sleep mode even if sleep was set to zero (#50)
|
|
|
|
|
*
|
|
|
|
|
* 3.9.12 20170208
|
2017-02-06 09:09:32 +00:00
|
|
|
* Fix compile error when webserver is disabled (#30)
|
2017-02-08 11:56:51 +00:00
|
|
|
* Fix possible ESP8285 flash problem by updating Flash Chip Mode to DOUT during OTA upload
|
|
|
|
|
* Fix hostname issues by not allowing user entry of string formatting and removing from user_config.h (#36)
|
2017-02-06 09:09:32 +00:00
|
|
|
*
|
|
|
|
|
* 3.9.11 20170204
|
2017-02-04 16:09:54 +00:00
|
|
|
* Fix command I2Cscan
|
|
|
|
|
* Fix not allowed spaces in Topic, ButtonTopic and SwitchTopic
|
|
|
|
|
* Make all TELEMETRY, STATUS and COMMAND message topics unique (#4)
|
|
|
|
|
* Advertise command topic to be used by iobroker (#299)
|
|
|
|
|
* Fix butten (non)detection if no GPIO_KEY1 is defined (#13)
|
|
|
|
|
* Change WeMo serialnumber from 7 decimal chars to 8 hexadecimal chars (#18)
|
|
|
|
|
* Update web page with Build Date/Time, Emulation and mDNS Discovery and Advertise information (#21)
|
|
|
|
|
*
|
|
|
|
|
* 3.9.10 20170130
|
|
|
|
|
* Add WS2812 Color Type selection (RGB or GRB) to user_config.h (#7)
|
|
|
|
|
* Hue api changes to support HUE App(s) (#8)
|
|
|
|
|
*
|
|
|
|
|
* 3.9.9 20170130
|
|
|
|
|
* Add command status 10 showing sensor data
|
|
|
|
|
* Fix hlw status messages if hlw is disabled
|
|
|
|
|
*
|
|
|
|
|
* 3.9.8 20170130
|
|
|
|
|
* Remove GPIO07 and GPIO08 from user selectable (#5)
|
|
|
|
|
*
|
|
|
|
|
* 3.9.7 20170129
|
2017-01-29 20:36:12 +00:00
|
|
|
* Fix possible WS2812 exceptions when using emulation
|
|
|
|
|
* Add command Emulation to dynamic configure Belkin WeMo and Hue Bridge for Alexa
|
|
|
|
|
*
|
|
|
|
|
* 3.9.6 20170129
|
2017-01-29 13:52:31 +00:00
|
|
|
* Add dynamic sleep for WS2812 animation (#1)
|
|
|
|
|
*
|
|
|
|
|
* 3.9.5 20170128
|
2017-01-28 15:31:11 +00:00
|
|
|
* Fix error message in case of wrong Domoticz command
|
|
|
|
|
*
|
|
|
|
|
* 3.9.4 20170127
|
2017-01-28 13:41:01 +00:00
|
|
|
* Fix Sonoff Dual Relay switching (#287)
|
|
|
|
|
*
|
|
|
|
|
* 3.9.3 20170127
|
|
|
|
|
* Add confirmation before Restart via webpage
|
2017-09-02 13:37:02 +01:00
|
|
|
* Expand Domoticz Configuration webpage with Key, Switch and Sensor Index and
|
2017-01-28 13:41:01 +00:00
|
|
|
* add commands DomoticzSwitchIdx and DomoticzSensorIdx (#86) (#174) (#219)
|
|
|
|
|
* Fix default DHT11 sensor driver selection
|
|
|
|
|
* Fix LedPower status after button press (#279)
|
|
|
|
|
* Add command Sleep 0 - 250 mSec for optional light sleep mode to lower energy consumption (#272)
|
|
|
|
|
* (Expect overall button/key/switch misses and wrong values on Sonoff Pow)
|
|
|
|
|
* Add Hue brightness extension (#281)
|
|
|
|
|
* Fix Hue brightness and change to call by reference (#283)
|
|
|
|
|
*
|
|
|
|
|
* 3.9.2 20170124
|
|
|
|
|
* Add confirmation before Reset Configuration via webpage (#244)
|
|
|
|
|
* Add WS2812 features (see Wiki commands)
|
|
|
|
|
*
|
|
|
|
|
* 3.9.1 20170124
|
|
|
|
|
* Change PowerOnState function to only trigger when Power On (and not just restart) (#238)
|
|
|
|
|
* Move HLW interrupts back to RAM and make WS2812_DMA optional as it generates Exception on Pow (#264)
|
|
|
|
|
* Add charset=utf-8 to webpages (#266)
|
|
|
|
|
* Update Hue emulation (#268)
|
|
|
|
|
* Fix status module number
|
|
|
|
|
* Add support for domoticz Dimmer on Sonoff_Led and WS2812
|
|
|
|
|
* Fix possible ESP8285 flash problem by updating Flash Chip Mode to DOUT during web upload
|
|
|
|
|
*
|
|
|
|
|
* 3.2.6a 20170120
|
|
|
|
|
* Fix Sonoff Pow compile error (#255)
|
|
|
|
|
* Move HLW interrupts back to ROM (Needed for WS2812 DMA interrupts)
|
|
|
|
|
* Removed all IO config from user_config.h as this will be done by commands or webpage
|
|
|
|
|
* Removed MessageFormat and supports JSON only except POWER/LIGHT status
|
|
|
|
|
* Add command LedPower to control main led (#247)
|
|
|
|
|
* Add more FriendlyNames for Hue (#254)
|
|
|
|
|
* Add DMA support for WS2812 when using pin 3 while other pins work just as well in my case...
|
|
|
|
|
* Add HUE emulation for Alexa (#229)
|
|
|
|
|
* Add basic WS2812 support (#229)
|
|
|
|
|
* Fix Wemo when MQTT is disabled (#245)
|
|
|
|
|
* Revert ButtonTopic and change SwitchTopic1 - 4 to one SwitchTopic
|
|
|
|
|
* Rename MqttUnits to Units
|
|
|
|
|
* Add Mqtt command to enable/disable MQTT
|
|
|
|
|
*
|
|
|
|
|
* 3.2.2a 20170115
|
|
|
|
|
* Add dynamic (Sonoff) Module, user GPIO and sensor selection (one size fits (almost) all)
|
|
|
|
|
* Add support for Sonoff LED
|
|
|
|
|
* Add Seriallog disable after 600 seconds for Sonoff Dual and 4 Channel
|
|
|
|
|
* Add ButtonTopic2 - 4, SwitchTopic1 - 4 and SwitchRetain
|
|
|
|
|
*
|
|
|
|
|
* 3.2.2 20170113
|
|
|
|
|
* Fix PowerOnState 2 functionality after re-applying power (#230)
|
|
|
|
|
*
|
|
|
|
|
* 3.2.1 20170113
|
|
|
|
|
* Fix some failed command decoding (#228)
|
|
|
|
|
* Removed passwords from status messages (#216)
|
|
|
|
|
*
|
|
|
|
|
* 3.2.0 20170111
|
|
|
|
|
* Add I2C BH1750 sensor (#222)
|
|
|
|
|
* Sensor rewrite preparing for online selection
|
|
|
|
|
*
|
|
|
|
|
* 3.1.16 20170109
|
|
|
|
|
* Fix Domoticz possible error condition
|
|
|
|
|
* Remove Wifi password from connection message (#216)
|
|
|
|
|
* Add Configure Other menu item to web page (#209)
|
|
|
|
|
* Add command FriendlyName, field Friendly Name and define FRIENDLY_NAME to be used by Alexa
|
|
|
|
|
* eliminating current use of MQTT_CLIENT_ID (#209)
|
|
|
|
|
* Add friendlyname to webpage replacing former hostname
|
|
|
|
|
*
|
|
|
|
|
* 3.1.15 20170108
|
2017-09-02 13:37:02 +01:00
|
|
|
* Fix Domoticz send key regression with Toggle command
|
2017-01-28 13:41:01 +00:00
|
|
|
*
|
|
|
|
|
* 3.1.14 20170107
|
|
|
|
|
* Add support for command TOGGLE (define MQTT_CMND_TOGGLE) when ButtonTopic is in use and not equal to Topic (#207)
|
|
|
|
|
*
|
|
|
|
|
* 3.1.13 20170107
|
|
|
|
|
* Fix web console command input when SUB_PREFIX contains '/' (#152)
|
|
|
|
|
* Add command response to web command (#200)
|
|
|
|
|
* Add option to disable MQTT as define USE_MQTT in user_config.h (#200)
|
|
|
|
|
*
|
|
|
|
|
* 3.1.12 20170106
|
|
|
|
|
* Add OTA retry to solve possible HTTP transient errors (#204)
|
|
|
|
|
* Fix MQTT host discovery
|
|
|
|
|
*
|
|
|
|
|
* 3.1.11 20170105
|
|
|
|
|
* Add mDNS to advertise webserver as <hostname>.local/
|
|
|
|
|
*
|
|
|
|
|
* 3.1.10 20170105
|
|
|
|
|
* Fix ButtonTopic when SUB_PREFIX = PUB_PREFIX
|
|
|
|
|
* Add workaround for possible MQTT queueing when SUB_PREFIX = PUB_PREFIX
|
|
|
|
|
* Add optional MQTT host discovery using define USE_DISCOVERY in user_config.h (#115)
|
|
|
|
|
*
|
|
|
|
|
* 3.1.9 20170104
|
|
|
|
|
* Fix Power Blink start position (toggled)
|
|
|
|
|
* Change PulseTime increments: 1 .. 111 in 0.1 sec (max 11 seconds) and 112 .. 64900 in seconds (= 12 seconds until 18 hours) (#188)
|
|
|
|
|
* Add support for SUB_PREFIX = PUB_PREFIX (#190)
|
|
|
|
|
*
|
|
|
|
|
* 3.1.8 20170103
|
|
|
|
|
* Add retain flag to LWT offline and only send "tele/sonoff/LWT Offline" (#179)
|
|
|
|
|
* Change retained LWT Online message to only send "tele/sonoff/LWT Online"
|
|
|
|
|
*
|
|
|
|
|
* 3.1.7 20161231
|
|
|
|
|
* Add retained message LWT Online when sonoff makes MQTT connection (#179)
|
|
|
|
|
*
|
|
|
|
|
* 3.1.6 20161230
|
|
|
|
|
* Add blinking using commands BlinkTime, BlinkCount and Power Blink|3|BlinkOff|4 (#165)
|
|
|
|
|
*
|
|
|
|
|
* 3.1.5 20161228
|
|
|
|
|
* Fix serial space command exception (28)
|
|
|
|
|
*
|
|
|
|
|
* 3.1.4 20161227
|
|
|
|
|
* Fix MQTT subscribe regression exception (3) (#162)
|
|
|
|
|
* Fix serial empty command exception (28)
|
|
|
|
|
*
|
|
|
|
|
* 3.1.3 20161225
|
|
|
|
|
* Extent Domoticz configuration webpage with optional indices (#153)
|
|
|
|
|
* Fix multi relay legacy tele message from tele/sonoff/2/POWER to tele/sonoff/POWER2
|
|
|
|
|
* Add support for iTead Motor Clockwise/Anticlockwise
|
|
|
|
|
*
|
|
|
|
|
* 3.1.2 20161224
|
|
|
|
|
* Extent command PowerOnState with toggle at power on (option 2 is now option 3!) (#156)
|
|
|
|
|
*
|
|
|
|
|
* 3.1.1 20161223
|
|
|
|
|
* Add support for Sonoff Touch and Sonoff 4CH (#40)
|
|
|
|
|
* Update DomoticzIdx and DomoticzKeyIdx with relay/key index (DomoticzIdx1/DomoticzKeyIdx1)
|
|
|
|
|
* Add command PowerOnState to control relay(s) at power on (#154)
|
|
|
|
|
*
|
|
|
|
|
* 3.1.0 20161221
|
|
|
|
|
* Add Sonoff Pow measurement smoothing
|
|
|
|
|
* Fix serial command topic preamble error (#151)
|
|
|
|
|
* Fix 2.x to 3.x migration inconsistencies (#146)
|
|
|
|
|
*
|
|
|
|
|
* 3.0.9 20161218
|
|
|
|
|
* Add Sonoff Pow voltage reading when relay is on but no load present (#123)
|
|
|
|
|
*
|
|
|
|
|
* 3.0.8 20161218
|
|
|
|
|
* Add temperature conversion to Fahrenheit as option in user_config.h (TEMP_CONVERSION) (#145)
|
|
|
|
|
*
|
|
|
|
|
* 3.0.7 20161217
|
|
|
|
|
* Add user_config_override.h to be used by user to override some defaults in user_config.h (#58)
|
|
|
|
|
* Fix Sonoff Pow low power (down to 4W) intermittent measurements (#123)
|
|
|
|
|
*
|
|
|
|
|
* 3.0.6 20161217
|
|
|
|
|
* Fix MQTT_CLIENT_ID starting with % sign as in "%06X" (#142)
|
|
|
|
|
* Add auto power off after PulseTime * 0.1 Sec to relay 1 (#134)
|
|
|
|
|
*
|
|
|
|
|
* 3.0.5 20161215
|
|
|
|
|
* Add more control over LED with command LedState options (#136, #143)
|
|
|
|
|
* LED_OFF (0), LED_POWER (1), LED_MQTTSUB (2), LED_POWER_MQTTSUB (3), LED_MQTTPUB (4), LED_POWER_MQTTPUB (5), LED_MQTT (6), LED_POWER_MQTT (7)
|
|
|
|
|
* Add option WIFI_RETRY (4) to command WifiConfig to allow connection retry to other AP without restart (#73)
|
|
|
|
|
*
|
|
|
|
|
* 3.0.4 20161211
|
|
|
|
|
* Fix intermittent Domoticz update misses (#133)
|
|
|
|
|
*
|
|
|
|
|
* 3.0.3 20161210
|
|
|
|
|
* Fix compiler warnings (#132)
|
|
|
|
|
* Remove redundant code
|
|
|
|
|
* Fix Domoticz pushbutton support
|
|
|
|
|
*
|
|
|
|
|
* 3.0.2 20161209
|
|
|
|
|
* Add pushbutton to SwitchMode (#130)
|
|
|
|
|
*
|
|
|
|
|
* 3.0.1 20161209
|
|
|
|
|
* Fix initial config
|
|
|
|
|
*
|
|
|
|
|
* 3.0.0 20161208
|
|
|
|
|
* Migrate and clean-up flash layout
|
|
|
|
|
* Settings from version 2.x are saved but settings from version 3.x can not be used with version 2.x
|
|
|
|
|
* Change SEND_TELEMETRY_RSSI to SEND_TELEMETRY_WIFI and add AP and SSID to telemetry
|
|
|
|
|
* Split long JSON messages
|
|
|
|
|
* Fix inconsistent status messages
|
|
|
|
|
* Fix all status messages to return JSON if enabled
|
|
|
|
|
* Remove relay index in cmnd/sonoff/<relay>/POWER now changed
|
|
|
|
|
* to cmnd/sonoff/POWER for single relay units
|
|
|
|
|
* and cmnd/sonoff/POWER<relay> for multi relay units like Sonoff dual
|
|
|
|
|
* Add retain option to Power/Light status controlled by command PowerRetain On|Off (#126)
|
|
|
|
|
*
|
|
|
|
|
* 2.1.2 20161204
|
|
|
|
|
* Add support for second wifi AP (#73)
|
|
|
|
|
* Update command WifiConfig
|
|
|
|
|
* Fix possible WifiManager hang
|
|
|
|
|
*
|
|
|
|
|
* 2.1.1a 20161203
|
|
|
|
|
* Fix scan for wifi networks if WeMo is enabled
|
|
|
|
|
* Fix syslog setting using web page
|
|
|
|
|
*
|
|
|
|
|
* 2.1.1 20161202
|
|
|
|
|
* Add support for ElectroDragon second relay and button (only toggle with optional ButtonTopic) (#110)
|
|
|
|
|
*
|
|
|
|
|
* 2.1.0 20161202
|
|
|
|
|
* Add optional EXPERIMENTAL TLS to MQTT (#49)
|
|
|
|
|
* Fix MQTT payload handling (#111)
|
|
|
|
|
* Optimzed WeMo code
|
|
|
|
|
*
|
|
|
|
|
* 2.0.21a 20161201
|
|
|
|
|
* Fix WeMo PowerPlug emulation
|
|
|
|
|
*
|
|
|
|
|
* 2.0.21 20161130
|
|
|
|
|
* Add Belkin WeMo PowerPlug emulation enabled with USE_WEMO_EMULATION in user_config.h (Heiko Krupp) (#105, #109)
|
|
|
|
|
*
|
|
|
|
|
* 2.0.20 20161130
|
|
|
|
|
* Relax MQTTClient naming but only allows hexadecimal uppercase numbers (#107)
|
|
|
|
|
* Add I2C support with command I2CScan
|
|
|
|
|
* Add I2C sensor driver for HTU21 as alternate sensor using TH10/16 connectors (Heiko Krupp) (#105)
|
|
|
|
|
* Add I2C sensor driver for BMP085/BMP180/BMP280/BME280 as alternate sensor using TH10/16 connectors
|
|
|
|
|
*
|
|
|
|
|
* 2.0.19a 20161127
|
|
|
|
|
* Add support for ButtonTopic and ButtonRetain to wall switch function
|
|
|
|
|
* Add pullup to SWITCH_PIN and command SwitchMode to syntax
|
|
|
|
|
*
|
|
|
|
|
* 2.0.18 20161126
|
|
|
|
|
* Add SUB_PREFIX multi level support allowing 'cmnd' or 'cmnd/level2/level3'
|
|
|
|
|
* Add wall switch function to GPIO14 and command SwitchMode (Alex Scott) (#103)
|
|
|
|
|
*
|
|
|
|
|
* 2.0.17 20161123
|
|
|
|
|
* Calibrate HLWPCAL from 12345 to 12530
|
|
|
|
|
* Add alternative sensor driver DHT2 using Adafruit DHT library
|
|
|
|
|
* Add define MESSAGE_FORMAT to user_config.h
|
|
|
|
|
* Throttle console messages
|
|
|
|
|
* Shorten JSON messages
|
|
|
|
|
* Fix possible Panic
|
|
|
|
|
* Fix User mode webserver security
|
|
|
|
|
*
|
|
|
|
|
* 2.0.16 20161118
|
|
|
|
|
* Add alternative sensor driver DS18x20 using OneWire library (#95)
|
|
|
|
|
* Change sensor MQTT message from tele/sonoff/TEMPERATURE to tele/sonoff/DHT/TEMPERATURE or
|
|
|
|
|
* tele/sonoff/DS18B20/TEMPERATURE or tele/sonoff/DS18x20/1/TEMPERATURE
|
|
|
|
|
* Add sensors to root webpage and auto refresh every 4 seconds (#92)
|
|
|
|
|
* Add optional JSON messageformat to all telemetry data
|
|
|
|
|
* Enforce minimum TelePeriod to be 10 seconds
|
|
|
|
|
* Fix Energy Yesterday reset after restart
|
|
|
|
|
* Add Energy Today restore after controlled restart
|
|
|
|
|
*
|
|
|
|
|
* 2.0.15 20161116
|
|
|
|
|
* Change TODAY_POWER and PERIOD_POWER to TODAY_ENERGY and PERIOD_ENERGY
|
|
|
|
|
* Fix serial regression
|
|
|
|
|
* Fix syslog hangs when loghost is unavailable
|
|
|
|
|
*
|
|
|
|
|
* 2.0.14 20161115
|
|
|
|
|
* Add HLW threshold delay
|
|
|
|
|
* Fix HLW intermittent current deviation
|
|
|
|
|
* Fix button functionality during wificonfig
|
|
|
|
|
* Add CRC check to DS18B20 sensor (#88)
|
|
|
|
|
*
|
|
|
|
|
* 2.0.13 20161113
|
|
|
|
|
* Add additional upload error code descriptions
|
|
|
|
|
* Add PlatformIO support (#80)
|
|
|
|
|
*
|
|
|
|
|
* 2.0.12 20161113
|
|
|
|
|
* Fix Serial and Web response regression when no MQTT connection available
|
|
|
|
|
* Fix Sonoff Dual power telemetric data for second relay
|
|
|
|
|
* Removed MQTT password from Information web page
|
|
|
|
|
* Hide MQTT password from Configure MQTT web page
|
|
|
|
|
*
|
|
|
|
|
* 2.0.11 20161111
|
|
|
|
|
* Rewrite button and web toggle code
|
|
|
|
|
* Fix NTP sync
|
|
|
|
|
* Add HLW calibration commands HLWPCAL, HLWUCAL and HLWICAL (need define USE_POWERCALIBRATION)
|
|
|
|
|
* Fix power threshold tests
|
|
|
|
|
*
|
|
|
|
|
* 2.0.10 20161109
|
|
|
|
|
* Add additional Domoticz define (#63)
|
|
|
|
|
* Add defines MQTT_STATUS_ON and MQTT_STATUS_OFF in user_config.h to select status On/Off string
|
|
|
|
|
* Fix status response differences (#65)
|
|
|
|
|
* Fix divide by zero exception (#70)
|
|
|
|
|
* Fix syslog loop exception
|
|
|
|
|
*
|
|
|
|
|
* 2.0.9 20161108
|
|
|
|
|
* clarify MODULE in user_config.h
|
|
|
|
|
* Fix hlw false values
|
|
|
|
|
*
|
|
|
|
|
* 2.0.8 20161108
|
|
|
|
|
* Add initial status after power on
|
|
|
|
|
* Seperate driver files
|
|
|
|
|
* Fix hlw code and calibrate Pow
|
|
|
|
|
* Move user config defines to user_config.h (#61)
|
|
|
|
|
*
|
|
|
|
|
* 2.0.7 20161030
|
|
|
|
|
* Make Ticker mandatory
|
|
|
|
|
* Add Domoticz support (Increase MQTT_MAX_PACKET_SIZE to 400) (#54)
|
|
|
|
|
* Add command MessageFormat 0|1 to select either legacy or JSON output
|
|
|
|
|
*
|
|
|
|
|
* 2.0.6 20161024
|
|
|
|
|
* Add Sonoff Pow power factor
|
|
|
|
|
* Initial support for up to four relays using iTEAD PSB (4Channel)
|
|
|
|
|
* - Currently only supports one button (All buttons behave the same)
|
|
|
|
|
* - Use command MODEL 4 to select four relay option
|
|
|
|
|
* (After first power on it will support 2 relays like Sonoff Dual)
|
|
|
|
|
* Fix ledstate
|
|
|
|
|
* Add command Status 9 to display Sonoff Pow thresholds
|
|
|
|
|
* Add commands PowerLow, PowerHigh, VoltageLow, VoltageHigh, CurrentLow and CurrentHigh for use
|
|
|
|
|
* with Sonoff Pow thresholds
|
|
|
|
|
*
|
|
|
|
|
* 2.0.5 20161018
|
|
|
|
|
* Add updates to user_config.h - moved SEND_TELEMETRY_DS18B20 and SEND_TELEMETRY_DHT to module area.
|
|
|
|
|
* As Sonoff TH10/16 does not have the logic installed for GPIO04 You'll have to select ONE of both
|
|
|
|
|
* Add Sonoff Pow support (experimental until Pow tested)
|
|
|
|
|
* Add command Status 8 to display Sonoff Pow energy values
|
|
|
|
|
* Add command MqttUnits On|Off to add units to values
|
|
|
|
|
* Change web main page header character size
|
|
|
|
|
* Change On/Off to ON/OFF status messages to satisfy openHAB
|
|
|
|
|
* Change TEMP to TEMPERATURE and HUM to HUMIDITY
|
|
|
|
|
*
|
|
|
|
|
* 2.0.4 20161009
|
|
|
|
|
* Add MQTT_BUTTON_RETAIN, SAVE_DATA and SAVE_STATE defines to user_config.h (#35)
|
|
|
|
|
* Update ButtonRetain to remove retained message(s) from broker when turned off
|
|
|
|
|
* Add Retain for second relay on Sonoff Dual
|
|
|
|
|
* Provide power status messages with device topic index if requested
|
|
|
|
|
*
|
|
|
|
|
* 2.0.3 20161008
|
|
|
|
|
* Update wifi initialization
|
|
|
|
|
* Add command BUTTONRETAIN for optional MQTT retain on button press (#35)
|
|
|
|
|
* Add command SAVESTATE to disable power state save. May be used with MQTT retain
|
|
|
|
|
*
|
|
|
|
|
* 2.0.2 20161006
|
|
|
|
|
* Fix wifi issue 2186
|
|
|
|
|
*
|
|
|
|
|
* 2.0.1 20161002
|
|
|
|
|
* Fix button press
|
|
|
|
|
*
|
|
|
|
|
* 2.0.0 20161002
|
|
|
|
|
* Update Sonoff TH10/16 sensor pins (My TH10 only has GPIO14 connected)
|
|
|
|
|
* Add full support for Sonoff dual
|
|
|
|
|
*
|
|
|
|
|
* 1.0.35 20160929
|
|
|
|
|
* Add more lines to console
|
|
|
|
|
* Add timeout and disable MQTT on web upload
|
|
|
|
|
* Add command SAVEDATA to control parameter save (for flash wear afficionados) (#30)
|
|
|
|
|
*
|
|
|
|
|
* 1.0.34 20160926
|
|
|
|
|
* Fix button press six and seven
|
|
|
|
|
* Add more information to webserver
|
|
|
|
|
*
|
|
|
|
|
* 1.0.33 20160915
|
|
|
|
|
* Better WPS error message
|
|
|
|
|
* Separate webserver code from support.ino into webserver.ino
|
|
|
|
|
* Fix webserver User by removing unwanted restart option
|
|
|
|
|
*
|
|
|
|
|
* 1.0.32 20160913
|
|
|
|
|
* Add Wifi Protected Setup (WPS) as third option for initial config
|
|
|
|
|
* Add command WIFICONFIG replacing deprecated command SMARTCONFIG
|
|
|
|
|
* Add option WIFICONFIG 3 to start WPSconfig
|
|
|
|
|
* Add option WIFICONFIG 0 to start saved Wifi config tool (WPSconfig, Smartconfig or Wifimanager)
|
|
|
|
|
* Change button behaviour - See Wiki
|
|
|
|
|
*
|
|
|
|
|
* 1.0.31 20160907
|
|
|
|
|
* Fix DS18B20 misread if teleperiod = 2
|
|
|
|
|
* Tuned sensor code
|
|
|
|
|
* Updated prefered ElectroDragon connection to Relay 1 and Button 1
|
|
|
|
|
* Moved SONOFF and ELECTRO_DRAGON port config to user_config.h
|
|
|
|
|
*
|
|
|
|
|
* 1.0.30 20160902
|
|
|
|
|
* Fix command TELEPERIOD 0
|
|
|
|
|
* Add ESP- tag to UDP log message for easy rsyslogd filtering
|
|
|
|
|
* Add ElectroDragon (Relay 2 only) functionality. Select with #define MODULE ELECTRO_DRAGON
|
|
|
|
|
* Add ? as null message alternative
|
|
|
|
|
* Add DHT temperature and humidity telemetry support. Enable with #define SEND_TELEMETRY_DHT
|
|
|
|
|
* Add DS18B20 temperature telemetry support. Enable with #define SEND_TELEMETRY_DS18B20
|
|
|
|
|
* Restrict HOSTNAME, MQTTCLIENT, TOPIC and BUTTONTOPIC in topic mode only
|
|
|
|
|
*
|
|
|
|
|
* 1.0.29 20160831
|
|
|
|
|
* Allow UPGRADE, OTAURL, RESTART, RESET, MQTTHOST, MQTTPORT, MQTTUSER, MQTTPASSWORD and WEBSERVER also in group mode
|
|
|
|
|
*
|
|
|
|
|
* 1.0.28 20160831
|
|
|
|
|
* Add webserver state to status 5
|
|
|
|
|
* Add optional PUB_PREFIX2 (tele) for telemetry usage
|
|
|
|
|
* Add command TELEPERIOD
|
|
|
|
|
* Fix syntax message
|
|
|
|
|
* Change memory status display
|
|
|
|
|
*
|
|
|
|
|
* 1.0.27 20160831
|
|
|
|
|
* Add sketch flash size
|
|
|
|
|
* Add console to webserver
|
|
|
|
|
* Add command weblog
|
|
|
|
|
* Change WifiManager web pages to minimal
|
|
|
|
|
* Change display default hostname and MQTT client id in webserver
|
|
|
|
|
* Change HTTP command interface to http://sonoff-1234/cm?cmnd=light 2
|
|
|
|
|
* Change HEARTBEAT to UPTIME
|
|
|
|
|
*
|
|
|
|
|
* 1.0.26 20160829
|
|
|
|
|
* Add define USE_WEBSERVER to disable web server code in source
|
|
|
|
|
* Add file upload as alternative for ota upload to webserver
|
|
|
|
|
* Add information to webserver
|
|
|
|
|
* Add command hostname
|
|
|
|
|
* Add command logport
|
|
|
|
|
* Change HTTP command interface to http://sonoff-1234/cmd?cmnd=light 2
|
|
|
|
|
* Change button behaviour with regards to Smartconfig and OTA upload. See README.md
|
|
|
|
|
* Enforce default hostname to either "%s-%04d" or user defined without any %
|
|
|
|
|
* Enforce default mqtt client id to either "DVES_%06X" or user defined without any %
|
|
|
|
|
*
|
|
|
|
|
* 1.0.25 20160822
|
|
|
|
|
* Remove config system halts to keep ota available
|
|
|
|
|
*
|
|
|
|
|
* 1.0.24 20160821
|
|
|
|
|
* Add test for MQTT_SUBTOPIC
|
|
|
|
|
* Change log range to LOG_LEVEL_ALL
|
|
|
|
|
* Change MQTT introduction messages
|
|
|
|
|
* Moved MQTT_MAX_PACKET_SIZE warning message to introduction messages
|
|
|
|
|
*
|
|
|
|
|
* 1.0.23 20160821
|
|
|
|
|
* Add option USE_SPIFFS to move config from flash to spiffs
|
|
|
|
|
* Add webserver with options 0 (off), 1 (user) and 2 (admin)
|
|
|
|
|
* Add HTTP command interface (http://sonoff-1234/c?cmnd=light 2)
|
|
|
|
|
* Add wifimanager countdown counter
|
|
|
|
|
* Add command line webpage
|
|
|
|
|
* Add relay control to wifimanager
|
|
|
|
|
* Add restart option 99 to force restart
|
|
|
|
|
* Fix wifi hostname
|
|
|
|
|
* Fix NETBIOS hostname problem by reducing default hostname length
|
|
|
|
|
* Fix possible exception if WIFI_HOSTNAME is changed
|
|
|
|
|
* Fix upgrade messages
|
|
|
|
|
* Reduce memory use by redesigning config routines
|
|
|
|
|
* Split syntax message
|
|
|
|
|
* Rename define SERIAL_IO to USE_SERIAL
|
|
|
|
|
*
|
|
|
|
|
* 1.0.22 20160814
|
|
|
|
|
* Add all MQTT parameters for configuration
|
|
|
|
|
* Add wifimanager to configure Wifi and MQTT via web server
|
|
|
|
|
* Change NTP time handling
|
|
|
|
|
* Fix Smartconfig parameter buffer overflow
|
|
|
|
|
* Fix PlatformIO warnings
|
|
|
|
|
*
|
|
|
|
|
* 1.0.21 20160808
|
|
|
|
|
* Remove semaphore as subscription flooding (more than 15 subscriptions per second) is managed by SDK (LmacRxBlk:1)
|
|
|
|
|
* Add optional RTC interrupt (define USE_TICKER) to keep RTC synced during subscription flooding
|
|
|
|
|
* Remove heartbeatflag
|
|
|
|
|
*
|
|
|
|
|
* 1.0.20 20160805
|
|
|
|
|
* Add semaphore to handle out of memory when too many subscriptions requested
|
|
|
|
|
* Use Daylight Saving (DST) parameters from user_config.h when timezone = 99
|
|
|
|
|
* Add status 7 option displaying RTC information
|
|
|
|
|
* Add ledstate to status 0
|
|
|
|
|
*
|
|
|
|
|
* 1.0.19 20160803
|
|
|
|
|
* Fix possible MQTT_CLIENT_ID induced Exception(28)
|
|
|
|
|
*
|
|
|
|
|
* 1.0.18 20160803
|
|
|
|
|
* Moved Cfg_Default
|
|
|
|
|
* Fix negative data handling
|
|
|
|
|
* Remove MQTT information from status 1 and add labels to status 1
|
|
|
|
|
* Add mac address to status 5
|
|
|
|
|
* Add MQTT ClientId, UserId and Password to status 6
|
|
|
|
|
*
|
|
|
|
|
* 1.0.17 20160731
|
|
|
|
|
* Better variable range checking
|
|
|
|
|
* Change ambiguous connection messages
|
|
|
|
|
* Add timestamp to serial message
|
|
|
|
|
*
|
|
|
|
|
* 1.0.16 20160729
|
|
|
|
|
* Moved wifi, rtc, syslog and config to support.ino
|
|
|
|
|
* Fixed button action when buttontopic is used. Introduced with 1.0.15
|
|
|
|
|
* Better buffer overflow checks (strlcpy)
|
|
|
|
|
*
|
|
|
|
|
* 1.0.15 20160728
|
|
|
|
|
* Removed pubsubclient config changes from sonoff.ino as it doesn't work
|
|
|
|
|
* reapply MQTT_MAX_PACKET_SIZE 256 and MQTT_KEEPALIVE 120 to PubSubClient.h
|
|
|
|
|
* Add status 0 option displaying all status messages
|
|
|
|
|
* Change MQTT_MAX_PACKET_SIZE from 1024 to 256
|
|
|
|
|
* Add buffer overflow checks (snprintf and strncpy)
|
|
|
|
|
* Implemented common string sizes
|
|
|
|
|
*
|
|
|
|
|
* 1.0.14 20160722
|
|
|
|
|
* Seperate user config from sonoff.ino to user_config.h (pucebaboon)
|
|
|
|
|
* Change defaults from sidnas2 to domus1
|
|
|
|
|
* Add MQTT status message as status 6 (pucebaboon)
|
|
|
|
|
* Add status type to message (pucebaboon)
|
|
|
|
|
* Add pubsubclient config changes to sonoff.ino (pucebaboon)
|
|
|
|
|
*
|
|
|
|
|
* 1.0.13 20160702
|
|
|
|
|
* Add Ledstate 1 option to show power state on led
|
|
|
|
|
*
|
|
|
|
|
* 1.0.12 20160529
|
|
|
|
|
* Allow disable of button topic using "0"
|
|
|
|
|
*
|
|
|
|
|
* 1.0.11 20160524
|
|
|
|
|
* Provide button response if MQTT connection lost
|
|
|
|
|
*
|
|
|
|
|
* 1.0.10 20160520
|
|
|
|
|
* Add optional button topic to assist external MQTT clients
|
|
|
|
|
* Change version notation
|
|
|
|
|
* Reset default values
|
|
|
|
|
*
|
|
|
|
|
* 1.0.9 20160503
|
|
|
|
|
* Add more blinks
|
|
|
|
|
* Add reset 2 option erasing flash
|
|
|
|
|
* Add status 5 option displaying network info
|
|
|
|
|
* Add syslog check for Wifi connection
|
2017-10-18 17:22:34 +01:00
|
|
|
* Resize MqttPublish log array
|
2017-01-28 13:41:01 +00:00
|
|
|
* Change Wifi smartconfig active from 100 to 60 seconds
|
|
|
|
|
* Update Wifi initialization
|
|
|
|
|
*
|
|
|
|
|
* 1.0.8 20160430
|
|
|
|
|
* Remove use of Wifi config data from SDK
|
|
|
|
|
* Add status 3 (syslog info) and status 4 (flash info)
|
|
|
|
|
* Add restart option to button (5 quick presses)
|
|
|
|
|
*
|
|
|
|
|
* 1.0.7 20160420
|
|
|
|
|
* Add UDP syslog support
|
|
|
|
|
* Change HOST command to MQTTHOST command
|
|
|
|
|
* Add commands SYSLOG, SERIALLOG and LOGHOST
|
|
|
|
|
* Change hostname to lower case to distinguise between open-sdk version
|
|
|
|
|
* Add support for ESP-12F used in my modified wkaku power socket switch
|
|
|
|
|
* Fix timezone command
|
|
|
|
|
* Add RTC month names for future use
|
|
|
|
|
* Modify button code
|
|
|
|
|
* Remove initialization errors by better use of MQTT loop
|
|
|
|
|
*
|
|
|
|
|
* 1.0.6 20160406
|
|
|
|
|
* Removed Wifi AP mode (#1)
|
|
|
|
|
* Add test for Arduino IDE version >= 1.6.8
|
|
|
|
|
* Fix RTC time sync code
|
|
|
|
|
*
|
|
|
|
|
* 1.0.5 20160310
|
|
|
|
|
* Initial public release
|
|
|
|
|
* Show debug info by selecting option from IDE Tools Debug port: Serial
|
2017-08-08 15:08:08 +01:00
|
|
|
*/
|