0cc1dd957b
Add SO98 to control user rotary support
2020-07-02 18:13:14 +02:00
03db100197
TuyaMCU baud rate
2020-06-29 11:01:55 -03:00
83bbe757db
Add command ``Module2``
...
Add command ``Module2`` to configure fallback module on fast reboot (#8464 )
2020-06-17 14:06:46 +02:00
715697cb32
Add ESP32 ethernet commands
...
Add ESP32 ethernet commands ``EthType 0/1``, ``EthAddress 0..31`` and ``EthClockMode 0..3`` (#8503 )
2020-06-16 18:36:49 +02:00
2181b0c1a4
Add serial to TCP bridge, ``TCPStart`` and ``TCPBaudRate`` (needs #define USE_TCP_BRIDGE)
2020-06-15 19:22:56 +02:00
ef0b797686
Add basic support for ESP32 ethernet
...
Add basic support for ESP32 ethernet adding commands ``Wifi 0/1`` and ``Ethernet 0/1`` both default ON (#8503 )
2020-06-15 18:27:04 +02:00
cdf7aa74bf
Add rule trigger ``System#Init``
...
Add rule trigger ``System#Init`` to allow early rule execution without wifi and mqtt initialized yet (#8673 )
2020-06-14 12:36:44 +02:00
5558da527a
Add MAX6675 sensor
...
This is basically a cut down version of MAX31855 without reference
temperature reading and lower resolution (only positive, 12bit only).
This implements 16bit protocol (31855 uses 32bit). SetOption94 enables
the new behavior.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
---
Changes:
v2:
* treat occasional 0xfff as an error
* do not add new sensor pins, use SetOption94 instead
2020-06-04 10:00:00 +10:00
eafaccfcda
Add support for up to two BH1750 sensors
...
Add support for up to two BH1750 sensors controlled by commands ``BH1750Resolution`` and ``BH1750MTime`` (#8139 )
2020-06-01 18:00:56 +02:00
bc6d7ceb87
Add support for SetOption88 to put each relay in a separate device groups
2020-05-26 22:07:25 -05:00
c333b67669
Fix DisplaySevenSegment compilation error
2020-05-25 10:21:36 +02:00
eb6de53628
Fix setting addr typo
2020-05-24 20:07:25 +02:00
dc9ce42888
Refactor LedPwm code
2020-05-23 13:04:17 +02:00
e780f25283
Gamma correction
...
Implement changes proposed by @s-hadinger review.
* Use 0-255 range in settings
* Apply gamma correction from xdrv_light & use changuintscale helper fn (as per pwm light routine)
2020-05-23 17:13:04 +10:00
603b628f97
Add pwm mode masking
...
* Extra setting & command to set - allows masking of pwm mode. Use case is for leds attached to buttons for seeing at night; this way user can combine both pwm and digital leds (i.e. pwm for the button leds but non-button status leds can stay on/off).
2020-05-20 13:23:54 +10:00
bd33574ee7
Align new settings to 2B boundaries
...
Attempting to fix settings not working correctly (might have mucked up the boundaries and compiler put a padding byte in).
2020-05-20 13:23:53 +10:00
a305f435e8
First pass at led pwm settings
...
* Added settings for ledpwm_on and ledpwm_off with defaults that mimic current digitalwrite function
* Changed ledpoweridx from digitalwrite to analogwrite
* Add commands to change new settings
2020-05-20 13:23:52 +10:00
a2b05399a3
Add automatic compression of Rules to achieve ~60% compression, added ``SetOption93 1`` to control caching of rules
2020-05-08 19:33:20 +02:00
f66a0ee561
Add Webcam commands
2020-05-08 17:17:09 +02:00
d78ca09c30
Integrate OpenTherm and WindMeter
2020-05-07 16:03:27 +02:00
cb1b7739b6
Merge branch 'development' into new-windmeter-sensor
2020-05-07 14:58:23 +02:00
9e6a809ba2
adapt to the latest development branch changes
2020-05-07 11:58:17 +03:00
a3455f235b
Merge branch 'development' into new-windmeter-sensor
...
# Conflicts:
# tasmota/language/bg_BG.h
# tasmota/language/cs_CZ.h
# tasmota/language/de_DE.h
# tasmota/language/el_GR.h
# tasmota/language/en_GB.h
# tasmota/language/es_ES.h
# tasmota/language/fr_FR.h
# tasmota/language/he_HE.h
# tasmota/language/hu_HU.h
# tasmota/language/it_IT.h
# tasmota/language/ko_KO.h
# tasmota/language/nl_NL.h
# tasmota/language/pl_PL.h
# tasmota/language/pt_BR.h
# tasmota/language/pt_PT.h
# tasmota/language/ro_RO.h
# tasmota/language/ru_RU.h
# tasmota/language/sk_SK.h
# tasmota/language/sv_SE.h
# tasmota/language/tr_TR.h
# tasmota/language/uk_UA.h
# tasmota/language/zh_CN.h
# tasmota/language/zh_TW.h
2020-05-06 21:33:07 +02:00
87f89f0a7d
Change max number of supported PCF8574 to four
...
Change max number of supported PCF8574 to four (#8355 )
2020-05-06 17:44:44 +02:00
097d51ea72
Merge branch 'development' into new-windmeter-sensor
...
# Conflicts:
# tasmota/language/bg-BG.h
# tasmota/language/cs-CZ.h
# tasmota/language/de-DE.h
# tasmota/language/el-GR.h
# tasmota/language/en-GB.h
# tasmota/language/es-ES.h
# tasmota/language/fr-FR.h
# tasmota/language/he-HE.h
# tasmota/language/hu-HU.h
# tasmota/language/it-IT.h
# tasmota/language/ko-KO.h
# tasmota/language/nl-NL.h
# tasmota/language/pl-PL.h
# tasmota/language/pt-BR.h
# tasmota/language/pt-PT.h
# tasmota/language/ro-RO.h
# tasmota/language/ru-RU.h
# tasmota/language/sk-SK.h
# tasmota/language/sv-SE.h
# tasmota/language/tr-TR.h
# tasmota/language/uk-UA.h
# tasmota/language/zh-CN.h
# tasmota/language/zh-TW.h
2020-05-05 09:07:03 +02:00
8bdd46a965
Start ESP32 webcam on GUI load
2020-05-04 17:13:14 +02:00
8f9bc1e5f7
Cleanup ESP32 webcam
2020-05-04 12:48:42 +02:00
691e1e9653
Merge branch 'development' into new-windmeter-sensor
2020-05-02 15:10:56 +02:00
5d18ad1c74
Add experimental basic support for ESP32
...
- Add experimental basic support for Tasmota on ESP32 based on work by Jörg Schüler-Maroldt
- Bump version to 8.2.0.6
- This ESP32 upgrade breaks current ESP32 templates
2020-05-01 17:30:09 +02:00
7dc7b631d4
Fix ESP32 settings size
...
Fix ESP32 settings size as regression from yesterday
2020-04-29 14:18:38 +02:00
c24de18278
Change ESP32 pin allocation part 1
2020-04-28 18:27:07 +02:00
e23b43f979
Add option for triggering a tele update under conditions
2020-04-28 14:02:05 +02:00
4536746d03
Update Changelog and Release notes
2020-04-28 11:09:56 +02:00
bdb5d92d85
Add variable for tele updates
2020-04-27 09:38:39 +02:00
dcc4623791
Merge branch 'development' into new-windmeter-sensor
2020-04-26 19:39:14 +02:00
b9aa6fe19d
Add configuration persistence fixing variable alignment problem
2020-04-26 19:21:10 +02:00
24709b9f6d
Add windmeter sensor
2020-04-26 09:43:52 +02:00
809a377154
Add Option to Activate PWM CT mode without select module 48
...
Hello,
I would like to share with you my extension of the code.
I have some new lamps that have 2 PWM channels that are not classically wired. The first one is for brightness and the other channel is for color temperature.
Tasmota has already integrated the possibility to switch between CWWW and CTBRI. I only built the possibility to set it up manually.
greetings,
Jens
PS: This is my first commit. If I did something wrong, please report it.
2020-04-22 19:43:57 +02:00
c37dde93c2
Add ESP32 QuickPowerCycle control
2020-04-19 15:36:04 +02:00
eab612871c
Fix ESP32 bootloop control using RTC memory
2020-04-19 14:18:12 +02:00
0f3619238f
Add ESP32 bootloop control
2020-04-19 13:08:04 +02:00
e1d7416a36
Add features to ESP32
...
- Decided to support ONLY flash mode DOUT (no software change but allows for RX1/TX1)
- Add GPIO9 (RX1) and GPIO10 (TX1) for hardware serial support
- Add above two GPIOs to template
- Moved basic ADC0 support from GPIO36 to GPIO33
2020-04-18 18:10:41 +02:00
d3b2f8c489
Add config version tag
...
- Add config version tag
- Bump version 8.2.0.4
2020-04-17 11:57:09 +02:00
d2b7b4012f
More ESP32 compatibility
...
More ESP32 compatibility (breaks current ESP32 configuration again!)
2020-04-16 14:59:01 +02:00
0f1cd33323
Update settings.h
2020-04-14 11:51:00 -03:00
8cf4a2ca50
Update settings.h
2020-04-14 10:46:22 -03:00
0c24651ed0
Add interval to PMS5003 sensor
...
Add interval to PMS5003 sensor to extend lifetime (#8128 )
2020-04-12 12:35:58 +02:00
54f7cf475d
create new setting pms_wake_interval for PMS sensor interval time
2020-04-11 10:37:12 -07:00
ed4cc8c226
Save 28 bytes in Settings for Zigbee configuration
2020-04-11 10:35:31 +02:00
2f627f98ce
support for AS3935, initial commit
2020-04-11 01:48:37 +02:00
93fd5dd618
Add experimental minimal support for ESP32
...
Add experimental minimal support for ESP32 (#8110 )
2020-04-10 18:24:08 +02:00
e69f103755
Small change to Settings var names
2020-04-09 11:40:26 +02:00
05af60074f
Add quick wifi connect using saved AP parameters
...
Add quick wifi connect using saved AP parameters when ``SetOption56 0`` (#3189 )
2020-04-07 12:19:54 +02:00
34fc92d6ca
Add command ``SetOption91 1`` to enable fading at startup / power on
2020-04-06 10:46:17 +02:00
4b09af8a36
Add BH1750 resolution control
...
Add command ``Sensor10 0/1/2`` to control BH1750 resolution - 0 = High (default), 1 = High2, 2 = Low (#8016 )
2020-04-01 16:46:12 +02:00
ec899817aa
Change some deepsleep wake messages
...
- Change remove MQTT Info messages on restart for DeepSleep Wake (#8044 )
- Add command ``SetOption90 1`` to disable non-json MQTT messages (#8044 )
2020-04-01 14:05:30 +02:00
bd34db87b1
Merge pull request #8021 from to-scho/feature/counter_debounce_low_high
...
Enhanced counter debouncing
2020-03-31 16:12:03 +02:00
d713468c0c
Add support for longer template names
...
Add support for longer template names
2020-03-29 17:41:31 +02:00
4a2f3d87c5
Enhanced counter debouncing
...
New commands CounterDebounceLow and CounterDebounceHigh to allow individual debounce times for low and high pulse widths to discard non valid falling edges. These are checked before legacy CounterDebounce checks distance between to valid falling edges.
Useful to have robust counter results when using e.g. an TCRT5000 optical sensor to count electromechanical "Ferraris" electricity meters.
2020-03-29 17:05:52 +02:00
e5a44e6326
Refactor template
2020-03-28 18:08:43 +01:00
5ba26780e9
Humidity Offset
2020-03-16 14:29:55 -03:00
8855d2a218
Add Zigbee use distinct MQTT topics per device for SENSOR, allowing retained messages ( #7835 )
2020-03-04 21:00:57 +01:00
669f88a5aa
Add Settings.flag2.speed_conversion
2020-03-02 14:00:57 +01:00
1973bb2474
Add support for Jarolift rollers by Keeloq algorithm
...
Add support for Jarolift rollers by Keeloq algorithm
2020-02-27 17:48:27 +01:00
3657cda425
resolved merge conflict
2020-02-27 17:22:28 +01:00
5cfe247611
Change default my_user_config.h driver and sensor support
...
Change default my_user_config.h driver and sensor support removing most sensors and adding most drivers
2020-02-27 15:10:42 +01:00
1f1c956b26
Use newly allocated settings and flags
2020-02-26 21:27:09 -06:00
878d93ebdb
Prepare for PWM Dimmer
...
Prepare for PWM Dimmer (#7791 )
2020-02-26 15:29:14 -06:00
f2074932f7
Clean up wifi connection / disconnection
2020-02-26 15:29:13 -06:00
1655c1b3aa
Add some wifi debug options
2020-02-26 15:29:12 -06:00
71340dc8b6
push travis, since it had an environment issue during last build
2020-02-26 20:10:29 +01:00
bc584468af
Using macro to exclude debug logs from code when compiling for production
2020-02-26 19:17:36 +01:00
f57a4d217c
Prepare for PWM Dimmer
...
Prepare for PWM Dimmer (#7791 )
2020-02-26 14:39:27 +01:00
407334be6b
Clean up wifi connection / disconnection
2020-02-26 13:45:46 +01:00
c1aedfc4c7
Merge branch 'development' into dev-arendst
2020-02-25 18:22:05 +01:00
3146bcf23a
Add some wifi debug options
2020-02-25 16:49:19 +01:00
d0bb1b36e4
Merge branch 'device-groups' of https://github.com/pcdiem/Tasmota into pwm-dimmer
2020-02-24 20:06:47 -06:00
fd610738ea
Merge branch 'development' of https://github.com/pcdiem/Tasmota into pwm-dimmer
2020-02-24 19:26:08 -06:00
dd3d9f3b21
Merge branch 'development' into dev-arendst
2020-02-24 19:41:12 +01:00
e25f14f37a
Jarolift shutter working with keeloq
2020-02-24 19:23:57 +01:00
9682da603a
Add Device Group storage
...
Add Device Group storage (#7786 )
2020-02-24 16:47:41 +01:00
c0a5156d8f
Initial pwm dimmer support
2020-02-24 07:19:15 -06:00
f409d7258e
Initial device groups support (power and light)
2020-02-21 09:09:21 -06:00
1a074da0b5
Add BootCount Reset Time to Status
...
Add BootCount Reset Time as BCResetTime to ``Status 1``
2020-02-07 12:38:10 +01:00
fab03d8173
Add ``SetOption84 1`` sends AWS IoT device shadow updates (alternative to retained)
2020-01-26 23:08:52 +01:00
3b71173a09
Add precision to Moisture sensor
...
Add precision to Moisture sensor (#7402 )
2020-01-23 18:13:32 +01:00
18ce64f813
Add Zigbee persistence and friendly names
2020-01-18 00:02:01 +01:00
8cf411a1c3
New command ShutterLock
...
Command shutterlock<x> 1 locks shutter <x> movement. Any ongoing movement is still finished when called. Subsequent calls of shutter commands about movement, web buttons and shutter buttons are blocked when shutter is locked. shutterlock<x> 0 unlocks shutter <x>.
2020-01-12 14:18:15 +01:00
aa665c1439
Add SetOption82 to limit the CT range for Alexa to 200..380
2020-01-04 11:01:44 +01:00
1e0550e750
Add command ShutterButton <parameters>
...
Add command ``ShutterButton <parameters>`` to control shutter(s) by to-scho (#7403 )
2020-01-02 15:12:59 +01:00
044fae2a6e
Update settings.h
2020-01-02 14:47:33 +01:00
406a5a15f5
Initial support for shutter button control
...
New command "ShutterButton<x> <a> <b> <c> <d> <e> <f> <g> <h> <i> <j>" added that allows to assign a tasmota button <x> to control shutter <a>.
Single press button shutter is set to position <b>. Double press button shutter is set to position <c>. Tripple press button shutter is set to position <d>. Hold button shutter is set to position <e>. Disabling any button action is given by <b> ... <e> equal to "-". Any press of the button while the shutter is moving will immediately stop that shutter.
Global steering of all your shutters at home is supported by MQTT. By any button action an MQTT command can be initiated to the <grouptopic> of the device. For single press button this can be enabled by <f> equal to "1". Disabling is indicated by <f> equal to "0". Double to hold actions are given by <g> ... <i>, correspondingly. When <j> is equal to "0" only "cmnd/<grouptopic>/Shutterposition<y> ..." with <y>=<x> is fired. When <j> is equal to "1" <y>=1...4 is used to control any shutter number of a tasmota device having same <grouptopic>.
Easy setup for an "up" button:
ShutterButton<x> <a> up (same as ShutterButton<x> <a> 100 50 74 100 0 0 0 1 1)
Single press will move shutter up to 100%, double press to 50% and tripple press to 74%. Holding the button for more than the hold time (SetOption32) moves all shutters with same <grouptopic> up to 100%.
Easy setup for an "down" button:
ShutterButton<x> <a> down (same as ShutterButton<x> <a> 0 50 24 0 0 0 0 1 1)
Single press will move shutter down to 0%, double press to 50% and tripple press to 24%. Holding the button for more than the hold time (SetOption32) moves all shutters with same <grouptopic> down to 0%.
Easy setup for an "updown" button:
ShutterButton<x> <a> updown (same as ShutterButton<x> <a> 100 0 50 - 0 0 0 0 0)
Single press will move shutter up to 100%, double press down to 0% and tripple press to 50%. No hold action and no other shutter control by MQTT.
2020-01-02 11:23:11 +01:00
8aa9109656
Happy New Year
...
Happy New Year
2019-12-31 14:23:34 +01:00
ed5330169a
HotPlug for sensors support added
2019-12-29 23:10:53 +03:00
aefb3fb9de
Reserve SetOption79
...
Used to enable resetting of the counter values to zero after telemetry data was transmitted.
2019-12-28 16:47:30 +02:00
a2478f9569
Change number of ``FriendlyName``s from 4 to 8
...
Change number of ``FriendlyName``s from 4 to 8
2019-12-24 15:06:19 +01:00
35e51918e3
Document Settings changes
2019-12-22 16:53:51 +01:00
ad4a7e91ac
Add support for max 150 characters
...
Add support for max 150 characters in most command parameter strings (#3686 , #4754 )
2019-12-22 15:23:52 +01:00
f55e02e800
Bump version to 8.0.0.1
...
Change Settings text handling allowing variable length text within a total text pool of 699 characters
2019-12-21 15:37:36 +01:00
7e24ed9c2c
Fix error message
2019-12-20 18:24:20 +01:00
3d59de5d1d
Bump version to 7.1.2.6
...
- Change some more Settings locations freeing up space for future single char allowing variable length text
- Add Zigbee support for Xiaomi Aqara Vibration Sensor and Presence Sensor by Stefan Hadinger
- Add Shutter functions ramp up/down and MQTT reporting by Stefan Bode
2019-12-14 13:16:55 +01:00
21fa1fa04e
Bump version to 7.1.2.5
...
Change some Settings locations freeing up space for future single char allowing variable length text
2019-12-13 12:05:07 +01:00
bfe2dc68cb
Fix statistics
2019-12-11 19:30:52 +01:00
eccc9f20f5
Add weight_change for #7170
...
Add weight_change for #7170
2019-12-11 11:54:27 +01:00
dfee90bd61
Changelog update
2019-12-09 15:15:16 +01:00
6c3d029286
Implement capability for setting CORS to a specific website instead of just enable for all websites
2019-12-08 21:07:39 +00:00
00fd7f2f7c
Bump version to 7.1.2.2
...
Add command ``SerialConfig 0..23`` or ``SerialConfig 8N1`` to select Serial Config (#7108 )
2019-12-06 15:02:05 +01:00
ac065867d3
Add command ``SetOption77 0/1``
...
Add command ``SetOption77 0/1`` to keep power on when slider is far left
2019-11-29 13:11:35 +01:00
14f6f6f22b
Add command TempOffset -12.6 .. 12.6
...
Add command TempOffset -12.6 .. 12.6 to set global temperature sensor offset (#6958 )
2019-11-18 12:15:49 +01:00
1cf4152747
Update settings.h
2019-11-18 09:31:39 +01:00
5c324357e6
Add command SetOption76 0/1
...
Add command SetOption76 0/1 to enable incrementing bootcount when deepsleep is enabled (#6930 )
2019-11-15 11:50:41 +01:00
e099ebe7b6
Bump version to 7.0.0.4
...
Add command WifiPower 0 .. 20.5 to set Wifi Output Power which will be default set to 17dB
2019-11-08 13:00:32 +01:00
1e29593469
Bump version 7.0.0.3
...
Initial support for I2C driver runtime control using command I2CDriver and document I2CDEVICES.md
2019-11-03 17:54:39 +01:00
4b49979274
Add SetOption comments to code
2019-11-03 13:51:22 +01:00
5f4e38023d
Add SetOption comments to code
2019-11-03 12:33:36 +01:00
57e62b1e68
Bump version 7.0.0.2
...
Add command WebColor19 to control color of Module and Name (#6811 )
2019-11-02 13:25:23 +01:00
d6115b7dd1
Add COLOR_TITLE as WebColor19
2019-11-02 05:33:40 +01:00
e497421ace
Add command SetOption75 0/1 to switch between grouptopic
...
Add command SetOption75 0/1 to switch between grouptopic (0) using fulltopic replacing %topic% or (1) is cmnd/<grouptopic> (#6779 )
2019-10-31 17:24:06 +01:00
50e1038c05
Add support for SetOption82-113
2019-10-31 12:12:48 +01:00
393f568276
Add Setoption74 to runtime configuration of internal pullup resistor usage for single DS18x20 sensor
2019-10-30 21:58:38 +02:00
fecf323678
Update settings.h
2019-10-30 09:32:06 +01:00
2dabaa3d20
Add command SetOption73 0/1 to re-enable CORS
...
Add command SetOption73 0/1 to re-enable HTTP Cross-Origin Resource Sharing (CORS) now default disabled (#6767 )
2019-10-28 13:36:04 +01:00
0e07397ff7
Change Sonoff-Tasmota to Tasmota
2019-10-27 12:04:08 +01:00
Theo Arends
Federico Leoni
Stephan Hadinger
Alexey Kardashevskiy
Paul C Diem
Norbert Richter
George
Yury Sannikov
Matteo Albinola
dermm
gururise
device111
to-scho
Hadinger
he.so
Leonid Muravjev
Andre Thomas
Shantur Rathore
stefanbode
localhost61
Bohdan Kmit