This commit fixes all known floating-point bugs with the pico-sdk. There
are two things going on here:
- Use a custom pico float component so that the pico-sdk doesn't include
its math functions, and then provide our own from lib/libm.
- Provide a wrapper for __aeabi_fadd to fix the infinity addition bug.
Prior to this commit, the following tests failed on the rp2 port: cmath_fun
float_parse math_domain math_domain_special math_fun_special. With this
commit, all these tests pass.
Thanks to @projectgus for how to approach this fix.
Signed-off-by: Damien George <damien@micropython.org>
The installation instructions for ESP32 TinyPICO board contained a typo
that used a non-standard baud rate 912600 instead of 921600. This made the
upload command fail on some Windows computers.
Signed-off-by: Scott Zhao <zhaomh1998@outlook.com>
The user memory area - accessible by machine.RTC.memory() -- will now
survive most reboot causes. A power-on reset (also caused by the EN pin on
some boards) will clean the memory. When this happens, the magic number
not found in the user memory will cause initialization.
After other resets (triggered by watchdogs, machine.reset(), ...), the user
is responsible to check and validate the contents of the user area.
This new behaviour can be changed by enabling
MICROPY_HW_RTC_MEM_INIT_ALWAYS: in that case the RTC memory is always
cleared on boot.
Signed-off-by: Thomas Wenrich <twenrich@gmail.com>
The amount of free IRAM in ESP32 SPIRAM builds is very small and went over
the limit due to commit 30b0ee34d3. This
commit enables further optimisations to reduce IRAM usage.
Signed-off-by: Damien George <damien@micropython.org>
Configures the I2S PLL to produce a frequency that the I2S clock generator
can use to create an optimal SCK frequency. The I2S PLL configuration
table is automatically generated at build time.
Fixes issue #10280.
Signed-off-by: Mike Teachman <mike.teachman@gmail.com>
This board has MICROPY_VFS enabled, which should take precedence over
MICROPY_MBFS (and did prior to 22d9116c8c).
Signed-off-by: Damien George <damien@micropython.org>
All ports using this common configuration already enable time/date
validation, so this commit is a no-op change.
Signed-off-by: Damien George <damien@micropython.org>
Also move MICROPY_PY_PENDSV_ENTER/REENTER/EXIT to mphalport.h, for ports
where these are not already there.
This helps separate the hardware implementation of these macros from the
MicroPython configuration (eg for renesas-ra and stm32, the IRQ static
inline helper functions can now be moved to irq.h).
Signed-off-by: Damien George <damien@micropython.org>
Changes:
- os.uname() is removed to save space; sys.version and sys.implementation
can be used instead.
- os.sync() now uses the common extmod version and syncs by calling the FAT
FS sync function, which eventually calls sflash_disk_flush().
Signed-off-by: Damien George <damien@micropython.org>
The os.dupterm() function has changed on this port, it now matches the
semantics used by all other ports (except it's restricted to accept only
machine.UART objects).
Signed-off-by: Damien George <damien@micropython.org>
Now that the MICROPY_BEGIN_ATOMIC_SECTION/MICROPY_END_ATOMIC_SECTION macros
act the same as disable_irq/enable_irq, it's possible to use the common
extmod implementation of these machine functions.
Signed-off-by: Damien George <damien@micropython.org>
This commit changes the cc3200 port to use the common machine
implementation of machine.disable_irq() and machine.enable_irq(). This
eliminates its dependency on the stm32 port's code. The behaviour of
cc3200 for these functions is changed:
- disable_irq() now returns an (opaque) integer rather than a bool
- enable_irq(state) must be passed and argument, which is the return value
of disable_irq() rather than a bool
Signed-off-by: Damien George <damien@micropython.org>
The ports esp32, mimxrt, rp2 and samd all shared exactly the same
implementation of machine.disable_irq() and machine.enable_irq(),
implemented in terms of MICROPY_{BEGIN,END}_ATOMIC_SECTION. This commit
factors these implementations into extmod/modmachine.c.
The cc3200, esp8266, nrf, renesas-ra and stm32 ports do not yet use this
common implementation.
Signed-off-by: Damien George <damien@micropython.org>
Minor changes for consistency are:
- nrf gains: unique_id(), freq() [they do nothing]
- samd: deepsleep() now resets after calling lightsleep()
- esp32: lightsleep()/deepsleep() no longer take kw arg "sleep", instead
it's positional to match others. also, passing 0 here will now do a 0ms
sleep instead of acting like nothing was passed.
reset_cause() no longer takes any args (before it would just ignore them)
- mimxrt: freq() with an argument and lightsleep() both raise
NotImplementedError
Signed-off-by: Damien George <damien@micropython.org>
And use it in all ports. The ports are unchanged, except esp8266 which now
just returns None from this function instead of the time elapsed (to match
other ports), and qemu-arm which gains this function.
Signed-off-by: Damien George <damien@micropython.org>
This is a code factoring to have the dict for the machine module in one
location, and all the ports use that same dict. The machine.soft_reset()
function implementation is also factored because it's the same for all
ports that did already implement it. Eventually more functions/bindings
can be factored.
All ports remain functionally the same, except:
- cc3200 port: gains soft_reset, mem8, mem16, mem32, Signal; loses POWER_ON
(which was a legacy constant, replaced long ago by PWRON_RESET)
- nrf port: gains Signal
- qemu-arm port: gains soft_reset
- unix port: gains soft_reset
- zephyr port: gains soft_reset, mem8, mem16, mem32
Signed-off-by: Damien George <damien@micropython.org>
Prior to this change, if a board did not define any hardware I2C pins, via
MICROPY_HW_I2Cx_SCL, then machine.I2C would alias to machine.SoftI2C.
That doesn't really make sense, and SoftI2C should always be used if there
is no hardware implementation. So this commit makes it so that machine.I2C
is only available if at least one set of I2C hardware pins are defined via
the MICROPY_HW_I2Cx_SCL/SDA macros.
For all boards that define at least one set of I2C hardware pins (which is
most of them) this commit is a no-op. The only boards that change are:
LEGO_HUB_NO6, LEGO_HUB_NO7, STM32H7B3I_DK.
Signed-off-by: Damien George <damien@micropython.org>
MICROPY_PY_MACHINE_SPI is defined in mpconfigport.h to be equal to
MICROPY_PY_MACHINE_HW_SPI, so they are equivalent options. The former one
is preferred because it's used by all other ports.
The default in mpconfigport.h is to enable this option, and all boards that
enable SPI have this removed from their mpconfigboard.h file so they pick
up the default.
Signed-off-by: Damien George <damien@micropython.org>
best_effort_wfe_or_timeout() already calls time_reached() and returns the
result of it, so no need to call it again.
Signed-off-by: Damien George <damien@micropython.org>
If a port defines MICROPY_SOFT_TIMER_TICKS_MS then soft_timer assumes a
SysTick back end, and provides a soft_timer_next variable that sets when
the next call to soft_timer_handler() should occur.
Otherwise, a port should provide soft_timer_get_ms() and
soft_timer_schedule_at_ms() with appropriate semantics (see comments).
Existing users of soft_timer should continue to work as they did.
Signed-off-by: Damien George <damien@micropython.org>
Commit 7ea06a3e26 moved the
`rmt_write_items()` call to fix RMT looping for ESP32-S3, but broke it for
the other ESP32s. This commit conditionally compiles the location of that
call.
Signed-off-by: Mark Blakeney <mark.blakeney@bullet-systems.net>
Prior to this change, after calling connect() the status() method for the
STA interface would either return STAT_GOT_IP or STAT_CONNECTION. The
latter would be returned because wifi_sta_connect_requested==true and
conf_wifi_sta_reconnects==0 by default. As such there was no way to know
anything about errors when attempting to connect, such as a bad password.
Now, status() can return STAT_NO_AP_FOUND and STAT_WRONG_PASSWORD when
those conditions are met.
Fixes issue #12930.
Signed-off-by: IhorNehrutsa <Ihor.Nehrutsa@gmail.com>
In ESP-IDF, enabling SPIRAM in menuconfig sets some Kconfig options:
- "Wi-Fi Cache TX Buffers" enabled. By default this tries to allocate 32 of
these when Wi-Fi is initialised, which requires 54,400 bytes of free heap.
- Switches "Type of WiFi TX buffers" from Dynamic to Static. This
pre-allocates all of the Wi-Fi transmit buffers.
Not a problem if PSRAM is initialised, but it's quite a lot of RAM if PSRAM
failed to initialise! As we use the same config for PSRAM & no-PSRAM builds
now, this either causes Wi-Fi to fail to initialise (seen on S2) or will
eat quite a lot of RAM.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
In commit 7c929d44 the console UART was changed to use the UART HAL.
Starting the UART HAL will change the UART clock from whatever it was
already configured at to UART_SCLK_DEFAULT. There is no "initialize at
existing settings" option.
This clock doesn't work with DFS.
The ESP-IDF code already takes this into account, and when DFS is enabled
it will configure the console UART to use the correct platform-specific
clock that will work with DFS.
The UART HAL init undoes this and sets it back to default.
This change will query the clock before the HAL init, then use the HAL
function to restore it back. Thus keeping the clock at the "correct"
value, which depends on platform, DFS status, and so on.
The clock frequency will be found using the UART driver function ESP-IDF
code uses for this. The existing code hard-coded a path that worked if the
clock was the APB clock and would fail otherwise.
The UART_NUM_0 define is removed because driver/uart.h already provides
this same macro.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
The behaviour described in the docs was not correct for either port.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
At some point the config changed such that no messages above Error level
were compiled into the final binary.
Fixes issue #12815.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
If the hard socket limit (default 16) is reached then it's possible that
socket allocation fails but garbage collection would allow it to succeed.
Perform a GC pass and try again before giving up, similar to the logic
elsewhere in MicroPython that tries a GC pass before raising MemoryError.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
LWIP doesn't implement a timeout for blocking connect(), and such a timeout
is not required by POSIX. However, CPython will use the socket timeout for
blocking connect on most platforms. The "principle of least surprise"
suggests we should support it on ESP32 as well (not to mention it's
useful!).
This provides the additional improvement that external exceptions (like
KeyboardInterrupt) are now handled immediately if they happen during
connect(). Previously Ctrl-C would not terminate a blocking connect until
connect() returned, but now it will.
Fixes issue #8326.
This work was funded through GitHub Sponsors.
Signed-off-by: Angus Gratton <angus@redyak.com.au>
This commit changes the Arduino board identifiers to correspond to their
official names. This helps to identify boards at runtime. At the moment
the Arduino Portenta H7 is reported as PORTENTA which is unfortunate as now
there is another Portenta board (Portenta C33) supported in MicroPython.
Also made the other identifiers for flash and network name consistent,
removed the incorrectly used MICROPY_PY_SYS_PLATFORM identifiers, and added
missing MICROPY_PY_NETWORK_HOSTNAME_DEFAULT identifiers.
Boards affected:
- stm32: ARDUINO_PORTENTA_H7, ARDUINO_GIGA, ARDUINO_NICLA_VISION
- renesas-ra: ARDUINO_PORTENTA_C33
- esp32: ARDUINO_NANO_ESP32
- rp2: ARDUINO_NANO_RP2040_CONNECT
Signed-off-by: Sebastian Romero <s.romero@arduino.cc>
Damien George
Scott Zhao
Thomas Wenrich
MikeTeachman
Carlosgg
iabdalkader
Mark Blakeney
Ihor Nehrutsa
Angus Gratton
Trent Piepho
Sebastian Romero