6.2.1.3 20180907
* Change web Configure Module GPIO drop down list order for better readability
* Fix showing Period Power in energy threshold messages
* Fix ButtonRetain to not use default topic for clearing retain messages (#3737)
* Add command Display to show all settings at once
* Add toggle function RGBW lights (#3695, #3697)
* Add user configurable GPIO02 and GPIO03 on H801 devices (#3692)
* Add optional MQTT_TELE_RETAIN to Energy Margins message (#3612, 3614)
* Add Individual HSBColorX commands (#3430, #3615)
* Add RuleX debug options 8,9,10 (StopOnError) to control RuleX execution status after an exception restart (#3607)
6.1.1.12 20180827
* Add commands ButtonDebounce 40..1000 and SwitchDebounce 40..1000 to have more control over debounce timing. Default is 50mS (#3594)
6.1.1.9
* Allow user override of define MAX_RULE_TIMERS (#3561)
* Allow user override of define MAX_RULE_VARS
* Add GPIO options ButtonXn, SwitchXn and CounterXn to select INPUT mode instead of INPUT_PULLUP (#2525)
* Fix OtaMagic when file path contains a dash (-) (#3563)
6.1.1b
* Add default Wifi Configuration tool as define WIFI_CONFIG_NO_SSID in user_config.h if no SSID is configured (#3224)
* Add user selection of Wifi Smartconfig as define USE_SMARTCONFIG in user_config.h
* Add user selection of WPS as define USE_WPS in user_config.h in preparation for core v2.4.2 (#3221)
* Change default Wifi config option from WPS to Wifi Manager if WPS is disabled
* or Wifi Smartconfig if webserver is disabled
* or Wifi Serial input if Smartconfig is disabled
* Remove WPS and SmartConfig from sonoff-minimal saving 56k code space
6.1.0b
* Add user selection of WPS as define USE_WPS in user_config.h in preparation for core v2.4.2 (#3221)
* Change default Wifi config option from WPS to Wifi Manager if WPS is disabled (or Wifi Smartconfig if webserver is disabled)
* Remove WPS from sonoff-minimal saving 33k code space
* Revert wifi changes implemented in v6.0.0a due to possible bad initial wifi connections
6.1.0a
* Add wifi and mqtt status led blinkyblinky to be disabled by SetOption31 1. Does not work when LedPower is On (deliberate) (#871, #2230, #3114, #3155)
* Remove not needed functionality from Sonoff-minimal to save space
6.0.0a
* Add command SetOption28 to switch between hex or decimal Sonoff Bridge
RF received data format (#3008)
* Add command SetOption29 to switch between hex or decimal IR received
data format
6.0.0a
* Add support for uploading Sonoff Bridge firmware found in
tools/fw_efm8bb1 folder build by Portisch using Web Gui File Upload
(#2886)
* Add command RfRaw to control Portisch firmware features
6.0.0a
* Add CRC to Settings making future upgrades more fail-safe
* Remove version 3, 4 and pre 5.2 settings auto-upgrade. See
https://github.com/arendst/Sonoff-Tasmota/wiki/Upgrade#migration-path
* Change default CFG_HOLDER from 0x20161209 to 4617 (=0x1209) - no
impact on default upgrades
5.12.0n
* Change ESP8266 Analog JSON message from {"Analog0:123"} to
{"ANALOG":{"A0:123"}} to accomodate rules (#2560)
* Change Counter JSON
message from {"Counter1":0,"Counter3":0} to {"COUNTER":{"C1":0,"C3":0}}
to accomodate rules
* Change ADS1115 JSON message from
{"ADS1115":{"Analog0":123,"Analog1":123}} to
{"ADS1115":{"A0":123,"A1":123}}
5.12.0k
* Prepare for simple rules by enlarging Settings area to now
2048 bytes
* Fix freeing more code space when emulation is disabled
(#1592)
* Fix compile error when not defined USE_TIMERS (#2400)
5.12.0h
* Add PWM status to command State if PWM enabled (#2203)
* Add
command HSBColor Hue,Sat,Bri (#1642, #2203)
* Add command Channel
0..100 to control dimmer value for individual color channels (#2111,
#2203)
5.12.0h
* Add support for Software Serial bridge using commands
SerialDelimiter, SBaudrate and SSerialSend. Supports 8N1 and text only
(#2190)
* Add support for Hardware Serial bridge using commands
SerialDelimiter, Baudrate and SerialSend. Supports 8N1 and text only
(#2182)
5.12.0c
* Fix intermittent exception when dns lookup is used while sleep is enabled
* Fix 5.4.0 regression turning off single press after button hold during 4x hold time
* Fix possible wifi connection problem by erasing sdk configuration parameters
5.12.0b
* Add serial debug info
* Add optional usage of %d or %X
suffices in MQTT client to append chipid (#1871)
* Add optional usage
of %d or %X suffices in MQTT topic to append chipid (#1871)
* Add
optional usage of %d or %04d in ota url to be replaced with chipid
(#1871)
* Add user configurable serial GPIOs to MagicHome and Arilux
modules (#1887)
5.12.0a
* Change platformio option sonoff-ds18x20 to sonoff-xxl
enabling ds18x20 and all other sensors in one image
* Fix providing web
page configuratin option for Friendly Name when no device (relay or
light) is configured (#1850)
* Change default paremeters in
user_config.h to undefined for easy installation (#1851)
* Change max
user configurable hold time from 10 to 25 seconds (#1851)
5.11.1j
* Prep for release
* Change uptime from hour to second
resulting in a display of 123T13:45:21 where 123 is days
* Fix Arilux
RF induced exception by moving interrupt handler to iram on non
esp/arduino lib v2.3.0
* Add NTP sync based on chip id (#1773)
5.11.1i
* Fix some Energy Monitoring related issues (#1677)
* Fix TSL2561 device detection (#1644)
* Fix command PWM response if no PWM channel is configured (#1783)
5.11.1i
* Fix some Energy Monitoring related issues
* Add command SetOption21 1 to allow Energy Monitoring when power is off
on Sonoff Pow and Sonoff S31 (#1420)
5.11.1i
* Update TasmotaSerial library to 1.1.0
* Rename commands
HlwPCal, HlwUCal and HlwICal to PowerCal, VoltageCal and CurrentCal to
be used for both Pow and S31 calibration
* Rename commands HlwPSet,
HlwUSet and HlwISet to PowerSet, VoltageSet and CurrentSet to be used
for both Pow and S31 calibration
* Add support for Sonoff S31 Smart
Socket with Power Consumption Detection (#1626)
* Fix IRReceive Data
value (#1663)
* Fix compiler warnings (#1774)
5.11.1g
* Add support for PMS5003 particle concentration sensor
*
Reinstate console weblog to 20 lines after some webpage rewrite
* Add
command SetOption20 to allow update of Dimmer/Color/Ct without turning
power on (#1719)
* Update language files nl-NL (#1723) and es-AR
(#1722)
5.11.1f
* Revert chunked webserver pages as it fails on many browsers
due to chunks being too small (#1706)
* Reduce initial console weblog
from 20 to 13 lines due to memory constraints
5.11.1e
* Replaced command Ina219Mode with command Sensor13
* Add
command Sensor15 2 to start MHZ19(B) Zero Point Calibration
* Add
chunked webserver pages for large pages saving memory
* Fix Non-English
JSON temperature unit attachement
* Fix Sonoff Pow Energy Today and
Energy Total reading after restart (#1648)
* Rewrite function pointers
to save code space and memory (#1683)
* Add option define
HOME_ASSISTANT_DISCOVERY_ENABLE in user_config.h (#1685)
* Fix SOnoff
Pow Energy Period roll-over (#1688)
5.11.1d
* Add locale Decimal Separator to Web sensor page
* Add
command State to retrieve device state information (same data as
teleperiod state and status 11 in slightly different JSON format)
*
Extent state information with Light parameters
* Fix IRSend parameter
translation (#1636)
* Add optional login to Webserver AP mode (#1587,
#1635)
* Fix BME680 teleperiod resistance measuring (#1647)
5.11.1c
* Make command color parameter input less strict to ease Hass
support
* Add ColorTemperature to light status message
* Change
PubSubClient.h define MQTT_MAX_PACKET_SIZE from 512 to 1000 for Hass
support
* Make define MESSZ dependent on PubSubClient.h define
MQTT_MAX_PACKET_SIZE
* Fix logging line length around 400 characters
*
Change module name Wemos D1 mini into Generic (#1220)
* Revert HTML
change from width=100% to style=width:100% supporting HTML5 (#1358)
*
Add experimental (still Hass python exceptions) Home Assistant Discovery
for switch and light to be enabled by command SetOption19 1 (#1534)
*
Updated French Translation (#1561)
* Fix DS18B20 temperature JSON
decimal dot (#1561)
* Add Spanish language file (#1589)
* Update
Italian Language file (#1594)
* Consolidate WIFI_MANAGER_SEC into
WIFI_CONFIG_SEC (#1616)
* Fix Energy JSON message (#1621)
5.11.1b
* Add command PowerOnState option 5 which inverts PulseTime and
allows for delayed always on after power on
* Changed
OSWATCH_RESET_TIME (Blocked loop) from 30 to 120 seconds to allow slow
networks (#1556)
* Add French language file (#1561)
* Fix truncated
command names and wrong response for DomoticzSwitchIdx (#1571)
* Add
HTTP Allow Cross Origin removed from ESP8266/Arduino 2.4.0 (#1572)
*
Fix %-sign issue as printf escape character in Humidity and Sonoff SC
(#1579)
5.11.1a
* Add automagic two step Web server OTA upgrade using
filename-minimal image if OTA free space is too small
* Add chinese
language file (#1551)
5.10.0i
* Add device function pointers
* Moved Command and JSON
English language defines to one file (i18n.h)
* Update it-IT.h language
file (#1449)
* Fix Wemo and Hue emulation by adding M-Search response
delay (#1486)
5.10.0f
* Differentiate between JSON text defines and other text
defines to allow for English JSON while using different locale (#1449)
* Fix display of build date and time in non-english locale (#1465)
5.10.0d
* Renamed commands Color2,3,4 to Color3,4,5
* Add command
Color2 to set color while keeping same dimmer value
* Add led signal to
Carbon Dioxide (CO2) sensors (see user_config.h)
* Fix Wemo Emulation
again (#1357)
* Updated German translation (#1438)
* Add support for SenseAir S8 CO2 sensor to be enabled with define
USE_SENSEAIR in user_config.h
* Add support for Domoticz Air Quality
sensor to be used by MH-Z19(B) and SenseAir sensors
5.10.0b
* Change Sonoff Pow Energy MQTT data JSON message and
consolidate Status 8 into Status 10
* Add optional support for PZEM004T
energy sensor to enable with define USE_PZEM004T in user_config.h (#614)
* Add (experimental) support for iTead SI7021 temperature and humidity
sensor (#735)
* Change ADS1115 default voltage range from +/-2V to
+/-6V (#1289)
5.10.0a
* Add (experimental) support for sensor SHT3x
* Change ADS1115
default voltage range from +/-2V to +/-4V (#1289)
* Add multipress
support and more user configurable options to Sonoff Dual R2 (#1291)
5.10.0a
* Add (experimental) support for sensor SHT3x
* Change ADS1115
default voltage range from +/-2V to +/-4V (#1289)
* Add multipress
support and more user configurable options to Sonoff Dual R2 (#1291)
5.9.1j
* Revert changes to xsns_05_ds18x20.ino and rename to
xsns_05_ds18x20_legacy.ino still needing library OneWire and providing
legacy JSON message:
*
"DS18x20":{"DS1":{"Type":"DS18B20","Address":"284CC48E04000079","Temperature":19.5},"DS2":{"Type":"DS18B20","Address":"283AC28304000052","Temperature":19.6}}
* Add new xdrv_05_ds18x20.ino free from library OneWire and add the
following features:
* Add support for DS1822
* Add forced setting of
12-bit resolution for selected device types (#1222)
* Add read
temperature retry counter (#1215)
* Fix lost sensors by performing
sensor probe at restart only thereby removing dynamic sensor probe
(#1215)
* Fix sensor address sorting using ascending sort on sensor
type followed by sensor address
* Rewrite JSON resulting in shorter
message allowing more sensors in default firmware image:
*
"DS18B20-1":{"Id":"00000483C23A","Temperature":19.5},"DS18B20-2":{"Id":"0000048EC44C","Temperature":19.6}
* Add additional define in user_config.h to select either single sensor
(defines disabled), new multi sensor (USE_DS18X20) or legacy multi
sensor (USE_DS18X20_LEGACY)
* Add support for Sonoff Dual R2 (#1249)
*
Fix ADS1115 detection (#1258)
5.9.1i
* Fix Arilux LC11 restart exception 0 after OTA upgrade
*
Disabled CRC lookup-table in OneWire.h (#define ONEWIRE_CRC8_TABLE 0) to
save some code space
* Rewrite xsns_05_ds18x20.ino adding support for
DS1822, correct address calculation and force setting 12-bit resolution
(#1222)
* DS18x20 sensor reconfiguration now only probed at restart
removing dynamic connection and intermittent sensor loss (#1215)
5.9.1g
* Fix typo ALIRFRCV into ARIRFRCV
* Add nicer clock support for
larger hand widths
* Add better clock support for different pixel
counts (#1226)
* Remove command EnergyReset 1..3
* Add commands
EnergyReset1 0..42500, EnergyReset2 0..42500 and EnergyReset3
0..42500000
* to (Re)set Energy Today, Yesterday or Total respectively
in Wh (#406, #685, #1202)
* Add SettingsSaveAll routine to command
SaveData to be used before controlled power down (#1202)
5.9.1f
* Upgrade library ArduinoJson to 5.11.2
* Upgrade library
IRRemoteEsp8266 to 2.2.1 + 2 commits but tweaked some protocols to keep
code usage small
* Upgrade library NeoPixelBus to 2.2.9
* Upgrade
library OneWire to 2.3.3 + 6 commits
* Formalize library PubSubClient
to 2.6 + 9 commits and additional delay
* Add optional ADS1115 driver
as alternative for unsupported I2Cdevlib in esp8266-core 2.4.0-rc2
*
Fix wrong response name for command HlwISet (#1214)
5.9.1e
* Add + (plus) and - (minus) to command color to select 1 out of
12 preset colors
* Add + (plus) and - (minus) to command ct to control
ColdWarm led ColorTemperature (+34/-34)
* Tune Arilux RF code
* Fix
possible iram1_0_seg compile error by shrinking ICACHE_RAM_ATTR code
*
Update core_esp8266_wiring_digital.c to latest (staged) level
*
Workaround Sonoff Bridge Learn Mode hang caused by unrecognised RF code
(#1181)
* Fix blank console log window by using XML character encoding
(#1187)
5.9.1d
* Add support for Arilux LC11 (CLearing RF home code when
selecting no Arilux module)
* Add fixed color options 1..12 to command
Color
* Add + (plus) and - (minus) to commands Dimmer (+10/-10), Speed
and Scheme
5.9.0b
* Add support for ADS1115 to be enabled in user_config.h and
needs libraries i2cdevlib-Core and i2cdevlib-ADS1115 (#338, #660)
* Fix
Exception 26 and empty console screen after usage of command
WakeupDuration (#1133)
* Fix some changed iTead web links in README.md
(#1137)
5.8.0o
* Remove max string length of 14 for Domoticz sensor
descriptions
* Add light scheme options (Color cycle Up, Down, Random)
and moving WS2812 schemes up by 3
* Add support for VEML6070 I2C Ultra
Violet level sensor (#1053)
5.8.0n
* Fix minimum TelePeriod of 10 seconds set by web page
* Shrink
information web page by 1k code space
* Removed Arduino IDE version too
low warning as it interferes with platformio.ini platform =
espressif8266_stage
* Add commands Color2, Color3, Color4, Width2,
Width3, Width4 and SetOption16 to set Ws2812 Clock parameters (#1019)
*
Add Polish language file (#1044, #1047)
* Add support for KMC 70011
Power Monitoring Smart Plug (#1045)
* Corrected German language file
(#1054)
5.8.0m
* Rewrite code (partly) using Google C++ Style Guide
(https://google.github.io/styleguide/cppguide.html)
* Allow empty
MqttHost name by using option 0
* Allow Mqtt server mDNS lookup only
when MqttHost name is empty (#1026)
* Change Ws2812 clock with more
flexible version (#1019)
* Add German language file (#1022)
* Support
connecting to MQTT brokers without userid and/or password (#1023)
* Add
commands PwmRange 1,255..1023 and PwmFrequency 1,100..4000 (#1025)
5.8.0l
* Update HTML/CSS to enable nicer form field entry
* Fix inverted relay status after restart or power on as regression from
5.8.0d (#909)
* Add send protocol Panasonic to IRsend (#1014)
* Fix relay power control when light power control is also configured as
regression from 5.8.0 (#1016)
5.8.0j
* Set default altitude to 0 to be used with pressure sensors
*
Document flash settings area for future use
* Prepare for 32-bit power
control (#995)
* Introduce sonoff.h master header
* Fix TLS MQTT SSL
fingerprint test (#808, #970)
* Fix pressure calculation for some BMP
versions regression introduced with version 5.8.0i (#974)
* Fix
Domoticz Dimmer set to same level not powering on (#945)
5.8.0i
* Add Domoticz counter sensor to IrReceive representing Received
IR Protocol and Data
* Fix Southern Hemisphere TIME_STD/TIME_DST
(#968)
* Add Sea level pressure calculation (#974)
* Fix virtual relay
status message used with Color/Dimmer control (#989)
* Fix command
IRSend and IRHvac case sensitive parameter regression introduced with
version 5.8.0 (#993)
5.8.0h
* Rename command IRRemote to IRSend (#956)
* Add IR Receiver
support. Disable in user_config.h (#956)
* Change default PWM
assignment for Witty Cloud to support optional Color/Dimmer control
(#976)
* GPIO12 (Green) from GPIO_PWM4 to GPIO_PWM2
* GPIO13
(Blue) from GPIO_PWM5 to GPIO_PWM3
* GPIO15 (Red) from GPIO_PWM3
to GPIO_PWM1
5.8.0f
* Set all saved power settings to Off when SetOption0
(SaveState) = 0 (#955)
* Allow PWM initialization after restart (#955)
* Add support for inverted PWM (#960)
5.8.0d
* Remove previous GPIO configuration when another module is
selected
* Fix inverted relay power on state (#909)
* Change default
PWM assignments for H801 RGB(CW) led controller to support optional
Color/Dimmer control
* GPIO04 (W2) from GPIO_PWM2 to GPIO_USER to
be user configurable for GPIO_PWM5 (second White - Warm if W1 is Cold)
* GPIO12 (Blue) GPIO_PWM3 no change
* GPIO13 (Green) from
GPIO_PWM4 to GPIO_PWM2
* GPIO14 (W1) from GPIO_PWM1 to GPIO_USER
to be user configurable for GPIO_PWM4 (first White - Cold or Warm)
*
GPIO15 (Red) from GPIO_PWM5 to GPIO_PWM1
* Change default PWM
assignments for MagicHome RGB(W) led controller to support optional
Color/Dimmer control
* GPIO05 (Green) from GPIO_PWM4 to GPIO_PWM2
*
GPIO12 (Blue) from GPIO_PWM5 to GPIO_PWM3
* GPIO13 (White) GPIO_USER
to be user configurable for GPIO_PWM4 (White - Cold or Warm)
* GPIO14
(Red) from GPIO_PWM3 to GPIO_PWM1
* Add command SetOption15 0
(default) for command PWM control or SetOption15 1 for commands
Color/Dimmer control to PWM RGB(CW) leds (#941)
5.8.0c
* Add warning to webpage when USE_MINIMAL is selected (#929)
*
Fix compile error when DOMOTICZ_UPDATE_TIMER is not defined (#930)
*
Fix alignment of web page items in some browsers (#935)
* Add smoother
movement of hour hand in WS2812 led clock (#936)
* Add support for
Magic Home RGBW Led controller (#940)
5.8.0b
* Fix command FullTopic entry when using serial or console
interface
* Fix possible UDP syslog blocking
* Add debug information
to MQTT subscribe
* Add Domoticz sensors for Voltage and Current (#903)
5.7.1j
* Remove the need for NeoPixelBus library for Hue support
*
Reintroduce xdrv_ws2812 for flexible future library changes
* Fix basic
On, Off, Toggle, Blink and BlinkOff commands when other language is
selected (#874)
5.7.1f
* Reduce code and string length for output of commands Modules
and GPIOs
* Add optional dimmer parameter to command Wakeup for
AiLight, Sonoff B1, Led and BN-SZ01 (#867)
5.7.1d
* Fix watchdog timeout caused by lack of stack space by now
using global buffers (#853)
* Removed webserver syslog disable as now
no longer needed
* Increased default MQTT message size from 368 to 405
bytes while keeping DMQTT_MAX_PACKET_SIZE = 512 (because we can)
* Fix
MQTT Offline or Remove MQTT retained topic code
* Allow command
SwitchTopic in group mode (#861)
* Allow command SwitchMode if no
switches are defined (#861)
5.7.1 20170909
* Remove leading spaces from MQTT data
* Fix webconsole
special character entry
* Allow # as prefix for color value
* Fix
Alexa detection and Hue App Update Request (#698, #854)
5.7.0 20170907
* Shrink module configuration webpage
* Fix settings order during startup to allow for displaying debug
messages
* Fix some string length issues
* Add more string length tests by using strncpy
* Add Ai-Thinker RGBW led (AiLight)
* Add Power check and add PulseTime to power check at startup (#526)
* Add Supla Espablo support (#755)
* Add more precision to Sonoff Pow period and power results using
command WattRes 0|1 (#759)
* Add basic internationalization and localization (#763)
* Add more Sonoff Pow range checking (#772)
* Fix invalid JSON (#786, #822)
* Add duplicate check to received RF signal within 2 seconds for Sonoff
Bridge (#810)
5.6.1 20170818
* Change module list order in webpage
* Fix Sonoff T1 1CH and 2CH configuration (#751)
*
* 5.6.0 20170818
* Fix Sonoff Pow intermittent exception 0
* Change Sonoff Pow sending Domoticz telemetry data only
* Add Ai-Thinker RGBW led (AiLight) (experimental)
* Add NeoPixelBus library to Sonoff Led for Hue support
* Add user configurable GPIO4 and GPIO5 to module Sonoff Bridge
* Add Sonoff B1 RGBCW led support with command Color RRGGBBCCWW (#676)
* Add command CT 152..500 to Sonoff Led and Sonoff B1 to control Color
Temperature
* Add Cold-Warm slider to web page for Sonoff Led and Sonoff B1
* Add CT parameter to Hue
* Add Sonoff T1 support (#582)
* Add AnalogInput0 if configured as Analog Input to webpage (#697, #746)
* Add command SetOption14 0|1 to enable interlock mode (#719, #721)
* Fix Mitsubishi HVAC IR power controll (#740)
5.6.0 20170818
* Fix Sonoff Pow intermittent exception 0
* Change Sonoff Pow sending Domoticz telemetry data only
* Add Ai-Thinker RGBW led (AiLight) (experimental)
* Add NeoPixelBus library to Sonoff Led for Hue support
* Add user configurable GPIO4 and GPIO5 to module Sonoff Bridge
* Add Sonoff B1 RGBCW led support with command Color RRGGBBCCWW (#676)
* Add command CT 152..500 to Sonoff Led and Sonoff B1 to control Color
Temperature
* Add Cold-Warm slider to web page for Sonoff Led and Sonoff B1
* Add CT parameter to Hue
* Add Sonoff T1 support (#582)
* Add AnalogInput0 if configured as Analog Input to webpage (#697, #746)
* Add command SetOption14 0|1 to enable interlock mode (#719, #721)
* Fix Mitsubishi HVAC IR power controll (#740)
5.5.2i
* Fix Sonoff Pow intermittent exception 0
* Change Sonoff Pow sending Domoticz telemetry data only
* Add Sonoff B1 RGBCW led support with command Color RRGGBBCCWW (#676)
* Add command CT 152..500 to Sonoff Led and Sonoff B1 to control Color
Temperature
* Add Cold-Warm slider to web page for Sonoff Led and Sonoff B1
* Add CT parameter to Hue
* Add Ai-Thinker RGBW led (AiLight) (experimental)
* Add NeoPixelBus library to Sonoff Led for Hue support (saves 1k code
space)
* Add user configurable GPIO4 and GPIO5 to module Sonoff Bridge
* Fix Mitsubishi HVAC IR power controll (#740)
* Add Sonoff T1 support (#582)
5.5.2 20170808
* Extent max number of WS2812 pixels from 256 to 512 (#667)
* Add OTA handling if server responds with no update available (#695)
* Removed undocumented command FlashMode (#696)
* Fix compile time error message due to increased message buffer size
(#703)
5.5.1b
* Extent max number of WS2812 pixels from 256 to 512 (#667)
* Add OTA handling if server responds with no update available (#695)
* Removed undocumented command FlashMode (#696)
* Fix compile time error message due to increased message buffer size (#703)
Theo Arends
andrethomas
Adrian Scillato
Rodney Gitzel
MadDoct
Norbert Richter
Theo Arends
Erik
gemu2015