Tasmota/tasmota/my_user_config.h

1332 lines
119 KiB
C
Raw Normal View History

/*
my_user_config.h - user specific configuration for Tasmota
2021-01-01 12:44:04 +00:00
Copyright (C) 2021 Theo Arends
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef _MY_USER_CONFIG_H_
#define _MY_USER_CONFIG_H_
2017-01-28 13:41:01 +00:00
/*********************************************************************************************\
2018-04-05 14:26:16 +01:00
* This file consists of TWO sections.
2017-01-28 13:41:01 +00:00
*
2018-04-05 14:26:16 +01:00
* SECTION 1:
* The first section contains PARAMETERS overriding flash settings if define CFG_HOLDER is CHANGED.
* All parameters can be persistent changed online using commands via MQTT, WebConsole or Serial.
* Corresponding MQTT/Serial/Console commands are shown in [brackets]
*
* SECTION 2:
* The second section contains Enabled and Disabled FEATURES allowing different program size.
* Changes in this section do NOT need a change of define CFG_HOLDER.
*
* ATTENTION:
2018-04-05 15:13:17 +01:00
* Users are advised to use the user_config_override.h file for most changes.
2017-01-28 13:41:01 +00:00
\*********************************************************************************************/
2018-04-05 14:26:16 +01:00
/*********************************************************************************************\
* SECTION 1
2018-04-05 15:13:17 +01:00
* - After initial load any change here only take effect if CFG_HOLDER is changed too
2018-04-05 14:26:16 +01:00
\*********************************************************************************************/
2017-01-28 13:41:01 +00:00
2018-04-05 14:26:16 +01:00
// -- Master parameter control --------------------
#define CFG_HOLDER 4617 // [Reset 1] Change this value (max 32000) to load SECTION1 configuration parameters to flash
// If following define is disabled it increases configuration corruption detection BUT
// it only allows firmware upgrades starting from version 6.6.0.11
2018-04-05 14:26:16 +01:00
// -- Project -------------------------------------
2019-10-27 11:04:08 +00:00
#define PROJECT "tasmota" // PROJECT is used as the default topic delimiter
// If not selected the default will be SONOFF_BASIC
//#define MODULE SONOFF_BASIC // [Module] Select default module from tasmota_template.h
#ifdef ESP8266
#define FALLBACK_MODULE SONOFF_BASIC // [Module2] Select default module on fast reboot where USER_MODULE is user template
//#define USER_TEMPLATE "{\"NAME\":\"Generic\",\"GPIO\":[1,1,1,1,1,1,1,1,1,1,1,1,1,1],\"FLAG\":0,\"BASE\":18}" // [Template] Set JSON template
2020-11-28 11:46:17 +00:00
#endif // ESP8266
#ifdef ESP32
#define FALLBACK_MODULE WEMOS // [Module2] Select default module on fast reboot where USER_MODULE is user template
//#define USER_TEMPLATE "{\"NAME\":\"ESP32-DevKit\",\"GPIO\":[1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,0,1,1,1,0,1,1,1,0,0,0,0,1,1,1,1,1,0,0,1],\"FLAG\":0,\"BASE\":1}" // [Template] Set JSON template
2020-11-28 11:46:17 +00:00
#endif // ESP32
2017-01-28 13:41:01 +00:00
#define SAVE_DATA 1 // [SaveData] Save changed parameters to Flash (0 = disable, 1 - 3600 seconds)
#define SAVE_STATE true // [SetOption0] Save changed power state to Flash (false = disable, true = enable)
#define BOOT_LOOP_OFFSET 1 // [SetOption36] Number of boot loops before starting restoring defaults (0 = disable, 1..200 = boot loops offset)
2017-01-28 13:41:01 +00:00
// -- Wi-Fi ---------------------------------------
#define WIFI_IP_ADDRESS "0.0.0.0" // [IpAddress1] Set to 0.0.0.0 for using DHCP or enter a static IP address
#define WIFI_GATEWAY "192.168.1.1" // [IpAddress2] If not using DHCP set Gateway IP address
#define WIFI_SUBNETMASK "255.255.255.0" // [IpAddress3] If not using DHCP set Network mask
2021-07-29 15:57:04 +01:00
#define WIFI_DNS "192.168.1.1" // [IpAddress4] If not using DHCP set DNS1 IP address (might be equal to WIFI_GATEWAY)
#define WIFI_DNS2 "0.0.0.0" // [IpAddress5] If not using DHCP set DNS2 IP address (might be equal to WIFI_GATEWAY)
#define STA_SSID1 "" // [Ssid1] Wi-Fi SSID
#define STA_PASS1 "" // [Password1] Wi-Fi password
#define STA_SSID2 "" // [Ssid2] Optional alternate AP Wi-Fi SSID
#define STA_PASS2 "" // [Password2] Optional alternate AP Wi-Fi password
#define WIFI_AP_PASSPHRASE "" // AccessPoint passphrase. For WPA2 min 8 char, for open use "" (max 63 char).
#define WIFI_CONFIG_TOOL WIFI_RETRY // [WifiConfig] Default tool if Wi-Fi fails to connect (default option: 4 - WIFI_RETRY)
// (WIFI_RESTART, WIFI_MANAGER, WIFI_RETRY, WIFI_WAIT, WIFI_SERIAL, WIFI_MANAGER_RESET_ONLY)
// The configuration can be changed after first setup using WifiConfig 0, 2, 4, 5, 6 and 7.
#define DNS_TIMEOUT 1000 // [DnsTimeout] Number of ms before DNS timeout
#define WIFI_ARP_INTERVAL 60 // [SetOption41] Send gratuitous ARP interval
#define WIFI_SCAN_AT_RESTART false // [SetOption56] Scan Wi-Fi network at restart for configured AP's
#define WIFI_SCAN_REGULARLY true // [SetOption57] Scan Wi-Fi network every 44 minutes for configured AP's
2022-04-19 16:26:57 +01:00
#define WIFI_NO_SLEEP false // [SetOption127] Sets Wifi in no-sleep mode which improves responsiveness on some routers
2017-01-28 13:41:01 +00:00
// -- Syslog --------------------------------------
#define SYS_LOG_HOST "" // [LogHost] (Linux) syslog host
2017-01-28 13:41:01 +00:00
#define SYS_LOG_PORT 514 // [LogPort] default syslog UDP port
#define SYS_LOG_LEVEL LOG_LEVEL_NONE // [SysLog] (LOG_LEVEL_NONE, LOG_LEVEL_ERROR, LOG_LEVEL_INFO, LOG_LEVEL_DEBUG, LOG_LEVEL_DEBUG_MORE)
#define SERIAL_LOG_LEVEL LOG_LEVEL_INFO // [SerialLog] (LOG_LEVEL_NONE, LOG_LEVEL_ERROR, LOG_LEVEL_INFO, LOG_LEVEL_DEBUG, LOG_LEVEL_DEBUG_MORE)
#define WEB_LOG_LEVEL LOG_LEVEL_INFO // [WebLog] (LOG_LEVEL_NONE, LOG_LEVEL_ERROR, LOG_LEVEL_INFO, LOG_LEVEL_DEBUG, LOG_LEVEL_DEBUG_MORE)
#define MQTT_LOG_LEVEL LOG_LEVEL_NONE // [MqttLog] (LOG_LEVEL_NONE, LOG_LEVEL_ERROR, LOG_LEVEL_INFO, LOG_LEVEL_DEBUG, LOG_LEVEL_DEBUG_MORE)
2017-01-28 13:41:01 +00:00
// -- MQTT ----------------------------------------
#define MQTT_USE true // [SetOption3] Select default MQTT use (false = Off, true = On)
#define MQTT_KEEPALIVE 30 // [MqttKeepAlive] Number of seconds between KeepAlive messages
#define MQTT_SOCKET_TIMEOUT 4 // [MqttTimeout] Number of seconds before Mqtt connection timeout
#define MQTT_WIFI_CLIENT_TIMEOUT 200 // [MqttWifiTimeout] Number of milliseconds before Mqtt Wi-Fi timeout
2018-04-05 14:26:16 +01:00
#define MQTT_HOST "" // [MqttHost]
2020-10-18 19:06:27 +01:00
#define MQTT_FINGERPRINT1 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00 // [MqttFingerprint1] (auto-learn)
#define MQTT_FINGERPRINT2 0xDA,0x39,0xA3,0xEE,0x5E,0x6B,0x4B,0x0D,0x32,0x55,0xBF,0xEF,0x95,0x60,0x18,0x90,0xAF,0xD8,0x07,0x09 // [MqttFingerprint2] (invalid)
2018-04-05 14:26:16 +01:00
#define MQTT_PORT 1883 // [MqttPort] MQTT port (10123 on CloudMQTT)
#define MQTT_USER "DVES_USER" // [MqttUser] MQTT user
#define MQTT_PASS "DVES_PASS" // [MqttPassword] MQTT password
2017-01-28 13:41:01 +00:00
#define MQTT_BUTTON_RETAIN false // [ButtonRetain] Button may send retain flag (false = off, true = on)
#define MQTT_POWER_RETAIN false // [PowerRetain] Power status message may send retain flag (false = off, true = on)
#define MQTT_SWITCH_RETAIN false // [SwitchRetain] Switch may send retain flag (false = off, true = on)
2020-01-21 11:36:44 +00:00
#define MQTT_SENSOR_RETAIN false // [SensorRetain] Sensor may send retain flag (false = off, true = on)
#define MQTT_INFO_RETAIN false // [InfoRetain] Info may send retain flag (false = off, true = on)
#define MQTT_STATE_RETAIN false // [StateRetain] State may send retain flag (false = off, true = on)
#define MQTT_STATUS_RETAIN false // [StatusRetain] Status may send retain flag (false = off, true = on)
#define MQTT_NO_HOLD_RETAIN false // [SetOption62] Disable retain flag on HOLD messages
#define MQTT_NO_RETAIN false // [SetOption104] No Retain - disable all MQTT retained messages, some brokers don't support it: AWS IoT, Losant
2017-01-28 13:41:01 +00:00
#define MQTT_STATUS_OFF "OFF" // [StateText1] Command or Status result when turned off (needs to be a string like "0" or "Off")
#define MQTT_STATUS_ON "ON" // [StateText2] Command or Status result when turned on (needs to be a string like "1" or "On")
#define MQTT_CMND_TOGGLE "TOGGLE" // [StateText3] Command to send when toggling (needs to be a string like "2" or "Toggle")
#define MQTT_CMND_HOLD "HOLD" // [StateText4] Command to send when button is kept down for over KEY_HOLD_TIME * 0.1 seconds (needs to be a string like "HOLD")
2017-01-28 13:41:01 +00:00
// -- MQTT topics ---------------------------------
2018-04-05 14:26:16 +01:00
// Example "tasmota/bedroom/%topic%/%prefix%/" up to 80 characers
#define MQTT_FULLTOPIC "%prefix%/%topic%/" // [FullTopic] Subscribe and Publish full topic name - Legacy topic
// %prefix% token options
2019-10-27 11:04:08 +00:00
#define SUB_PREFIX "cmnd" // [Prefix1] Tasmota devices subscribe to %prefix%/%topic% being SUB_PREFIX/MQTT_TOPIC and SUB_PREFIX/MQTT_GRPTOPIC
#define PUB_PREFIX "stat" // [Prefix2] Tasmota devices publish to %prefix%/%topic% being PUB_PREFIX/MQTT_TOPIC
#define PUB_PREFIX2 "tele" // [Prefix3] Tasmota devices publish telemetry data to %prefix%/%topic% being PUB_PREFIX2/MQTT_TOPIC/UPTIME, POWER and TIME
// May be named the same as PUB_PREFIX
// %topic% token options (also ButtonTopic and SwitchTopic)
#define MQTT_TOPIC PROJECT "_%06X" // [Topic] unique MQTT device topic including (part of) device MAC address
2019-10-27 11:04:08 +00:00
#define MQTT_GRPTOPIC "tasmotas" // [GroupTopic] MQTT Group topic
#define MQTT_GROUPTOPIC_FORMAT false // [SetOption75] GroupTopic replaces %topic% (false) or fixed topic cmnd/grouptopic (true)
#define MQTT_BUTTON_TOPIC "0" // [ButtonTopic] MQTT button topic, "0" = same as MQTT_TOPIC, set to 'PROJECT "_BTN_%06X"' for unique topic including device MAC address
#define MQTT_SWITCH_TOPIC "0" // [SwitchTopic] MQTT button topic, "0" = same as MQTT_TOPIC, set to 'PROJECT "_SW_%06X"' for unique topic including device MAC address
#define MQTT_CLIENT_ID "DVES_%06X" // [MqttClient] Also fall back topic using last 6 characters of MAC address or use "DVES_%12X" for complete MAC address
2017-01-28 13:41:01 +00:00
// -- MQTT - Telemetry ----------------------------
#define TELE_PERIOD 300 // [TelePeriod] Telemetry (0 = disable, 10 - 3600 seconds)
#define TELE_ON_POWER false // [SetOption59] send tele/STATE together with stat/RESULT (false = Disable, true = Enable)
2017-01-28 13:41:01 +00:00
// -- MQTT - Domoticz -----------------------------
2018-04-05 14:26:16 +01:00
#define DOMOTICZ_UPDATE_TIMER 0 // [DomoticzUpdateTimer] Send relay status (0 = disable, 1 - 3600 seconds)
2017-01-28 13:41:01 +00:00
// -- MQTT - Home Assistant Discovery -------------
#define HOME_ASSISTANT_DISCOVERY_ENABLE false // [SetOption19] Home Assistant Discovery (false = Disable, true = Enable)
#define HASS_AS_LIGHT false // [SetOption30] Enforce HAss autodiscovery as light
2020-06-18 18:43:18 +01:00
//#define DEEPSLEEP_LWT_HA_DISCOVERY // Enable LWT topic and its payloads for read-only sensors (Status sensor not included) and binary_sensors on HAss Discovery (Commented out: all read-only sensors and binary_sensors
// won't be shown as OFFLINE on Home Assistant when the device is DeepSleeping - NOTE: This is only for read-only sensors and binary_sensors, relays will be shown as OFFLINE)
// -- MQTT - Options ------------------------------
#define MQTT_RESULT_COMMAND false // [SetOption4] Switch between MQTT RESULT or COMMAND
#define MQTT_LWT_MESSAGE false // [SetOption10] Switch between MQTT LWT OFFLINE or empty message
#define MQTT_POWER_FORMAT false // [SetOption26] Switch between POWER or POWER1 for single power devices
#define MQTT_APPEND_TIMEZONE false // [SetOption52] Append timezone to JSON time
#define MQTT_BUTTON_SWITCH_FORCE_LOCAL false // [SetOption61] Force local operation when button/switch topic is set (false = off, true = on)
#define MQTT_INDEX_SEPARATOR false // [SetOption64] Enable "_" instead of "-" as sensor index separator
#define MQTT_TUYA_RECEIVED false // [SetOption66] Enable TuyaMcuReceived messages over Mqtt
#define MQTT_TLS_ENABLED false // [SetOption103] Enable TLS mode (requires TLS version)
#define MQTT_TLS_FINGERPRINT false // [SetOption132] Force TLS fingerprint validation instead of CA (requires TLS version)
2017-01-28 13:41:01 +00:00
// -- HTTP ----------------------------------------
2018-04-05 14:26:16 +01:00
#define WEB_SERVER 2 // [WebServer] Web server (0 = Off, 1 = Start as User, 2 = Start as Admin)
#define WEB_PASSWORD "" // [WebPassword] Web server Admin mode Password for WEB_USERNAME (empty string = Disable)
2019-10-27 11:04:08 +00:00
#define FRIENDLY_NAME "Tasmota" // [FriendlyName] Friendlyname up to 32 characters used by webpages and Alexa
2018-04-05 14:26:16 +01:00
#define EMULATION EMUL_NONE // [Emulation] Select Belkin WeMo (single relay/light) or Hue Bridge emulation (multi relay/light) (EMUL_NONE, EMUL_WEMO or EMUL_HUE)
#define EMULATION_HUE_1ST_GEN false // [Emulation] Force SetOption109 1 - if you only have Echo Dot 2nd gen devices
2021-08-05 16:50:56 +01:00
//#define USE_CORS // [Cors] Enable CORS - Be aware that this feature is unsecure ATM (https://github.com/arendst/Tasmota/issues/6767)
#define CORS_DOMAIN "" // [Cors] CORS Domain for preflight requests
2019-12-09 14:15:16 +00:00
// -- HTTP Options --------------------------------
#define GUI_SHOW_HOSTNAME false // [SetOption53] Show hostname and IP address in GUI main menu
2019-10-28 08:54:23 +00:00
// -- HTTP GUI Colors -----------------------------
// HTML hex color codes. Only 3 and 6 digit hex string values are supported!! See https://www.w3schools.com/colors/colors_hex.asp
// Light theme - pre v7
// WebColor {"WebColor":["#000","#fff","#f2f2f2","#000","#fff","#000","#fff","#f00","#008000","#fff","#1fa3ec","#0e70a4","#d43535","#931f1f","#47c266","#5aaf6f","#fff","#999","#000"]}
2019-10-28 08:54:23 +00:00
/*
#define COLOR_TEXT "#000" // [WebColor1] Global text color - Black
#define COLOR_BACKGROUND "#fff" // [WebColor2] Global background color - White
#define COLOR_FORM "#f2f2f2" // [WebColor3] Form background color - Greyish
#define COLOR_INPUT_TEXT "#000" // [WebColor4] Input text color - Black
#define COLOR_INPUT "#fff" // [WebColor5] Input background color - White
#define COLOR_CONSOLE_TEXT "#000" // [WebColor6] Console text color - Black
#define COLOR_CONSOLE "#fff" // [WebColor7] Console background color - White
#define COLOR_TEXT_WARNING "#f00" // [WebColor8] Warning text color - Red
#define COLOR_TEXT_SUCCESS "#008000" // [WebColor9] Success text color - Dark lime green
#define COLOR_BUTTON_TEXT "#fff" // [WebColor10] Button text color - White
#define COLOR_BUTTON "#1fa3ec" // [WebColor11] Button color - Vivid blue
#define COLOR_BUTTON_HOVER "#0e70a4" // [WebColor12] Button color when hovered over - Dark blue
#define COLOR_BUTTON_RESET "#d43535" // [WebColor13] Restart/Reset/Delete button color - Strong red
#define COLOR_BUTTON_RESET_HOVER "#931f1f" // [WebColor14] Restart/Reset/Delete button color when hovered over - Dark red
#define COLOR_BUTTON_SAVE "#47c266" // [WebColor15] Save button color - Moderate lime green
#define COLOR_BUTTON_SAVE_HOVER "#5aaf6f" // [WebColor16] Save button color when hovered over - Dark moderate lime green
#define COLOR_TIMER_TAB_TEXT "#fff" // [WebColor17] Config timer tab text color - White
#define COLOR_TIMER_TAB_BACKGROUND "#999" // [WebColor18] Config timer tab background color - Dark gray
#define COLOR_TITLE_TEXT "#000" // [WebColor19] Title text color - Whiteish
*/
// Dark theme
// WebColor {"WebColor":["#eaeaea","#252525","#4f4f4f","#000","#ddd","#65c115","#1f1f1f","#ff5661","#008000","#faffff","#1fa3ec","#0e70a4","#d43535","#931f1f","#47c266","#5aaf6f","#faffff","#999","#eaeaea"]}
#define COLOR_TEXT "#eaeaea" // [WebColor1] Global text color - Very light gray
#define COLOR_BACKGROUND "#252525" // [WebColor2] Global background color - Very dark gray (mostly black)
#define COLOR_FORM "#4f4f4f" // [WebColor3] Form background color - Very dark gray
#define COLOR_INPUT_TEXT "#000" // [WebColor4] Input text color - Black
#define COLOR_INPUT "#ddd" // [WebColor5] Input background color - Very light gray
#define COLOR_CONSOLE_TEXT "#65c115" // [WebColor6] Console text color - Strong Green
#define COLOR_CONSOLE "#1f1f1f" // [WebColor7] Console background color - Very dark gray (mostly black)
#define COLOR_TEXT_WARNING "#ff5661" // [WebColor8] Warning text color - Brick Red
#define COLOR_TEXT_SUCCESS "#008000" // [WebColor9] Success text color - Dark lime green
#define COLOR_BUTTON_TEXT "#faffff" // [WebColor10] Button text color - Very pale (mostly white) cyan
#define COLOR_BUTTON "#1fa3ec" // [WebColor11] Button color - Vivid blue
#define COLOR_BUTTON_HOVER "#0e70a4" // [WebColor12] Button color when hovered over - Dark blue
#define COLOR_BUTTON_RESET "#d43535" // [WebColor13] Restart/Reset/Delete button color - Strong red
#define COLOR_BUTTON_RESET_HOVER "#931f1f" // [WebColor14] Restart/Reset/Delete button color when hovered over - Dark red
#define COLOR_BUTTON_SAVE "#47c266" // [WebColor15] Save button color - Moderate lime green
#define COLOR_BUTTON_SAVE_HOVER "#5aaf6f" // [WebColor16] Save button color when hovered over - Dark moderate lime green
#define COLOR_TIMER_TAB_TEXT "#faffff" // [WebColor17] Config timer tab text color - Very pale (mostly white) cyan.
#define COLOR_TIMER_TAB_BACKGROUND "#999" // [WebColor18] Config timer tab background color - Dark gray
#define COLOR_TITLE_TEXT "#eaeaea" // [WebColor19] Title text color - Very light gray
2017-01-28 13:41:01 +00:00
2020-01-21 11:36:44 +00:00
// -- KNX -----------------------------------------
#define KNX_ENABLED false // [Knx_Enabled] Enable KNX protocol
#define KNX_ENHANCED false // [Knx_Enhanced] Enable KNX Enhanced Mode
// -- mDNS ----------------------------------------
#define MDNS_ENABLED false // [SetOption55] Use mDNS (false = Disable, true = Enable)
2017-01-28 13:41:01 +00:00
// -- Time - Up to three NTP servers in your region
#define NTP_SERVER1 "2.pool.ntp.org" // [NtpServer1] Select first NTP server by name or IP address (135.125.104.101, 2001:418:3ff::53)
#define NTP_SERVER2 "2.europe.pool.ntp.org" // [NtpServer2] Select second NTP server by name or IP address (192.36.143.134, 2a00:2381:19c6::100)
#define NTP_SERVER3 "2.nl.pool.ntp.org" // [NtpServer3] Select third NTP server by name or IP address (46.249.42.13, 2603:c022:c003:c900::4)
// To manually set:
// BackLog NtpServer1 2.pool.ntp.org; NtpServer2 2.europe.pool.ntp.org; NtpServer3 2.nl.pool.ntp.org
2017-01-28 13:41:01 +00:00
// -- Time - Start Daylight Saving Time and timezone offset from UTC in minutes
#define TIME_DST_HEMISPHERE North // [TimeDst] Hemisphere (0 or North, 1 or South)
#define TIME_DST_WEEK Last // Week of month (0 or Last, 1 or First, 2 or Second, 3 or Third, 4 or Fourth)
#define TIME_DST_DAY Sun // Day of week (1 or Sun, 2 or Mon, 3 or Tue, 4 or Wed, 5 or Thu, 6 or Fri, 7 or Sat)
#define TIME_DST_MONTH Mar // Month (1 or Jan, 2 or Feb, 3 or Mar, 4 or Apr, 5 or May, 6 or Jun, 7 or Jul, 8 or Aug, 9 or Sep, 10 or Oct, 11 or Nov, 12 or Dec)
#define TIME_DST_HOUR 2 // Hour (0 to 23)
#define TIME_DST_OFFSET +120 // Offset from UTC in minutes (-780 to +780)
// -- Time - Start Standard Time and timezone offset from UTC in minutes
#define TIME_STD_HEMISPHERE North // [TimeStd] Hemisphere (0 or North, 1 or South)
#define TIME_STD_WEEK Last // Week of month (0 or Last, 1 or First, 2 or Second, 3 or Third, 4 or Fourth)
#define TIME_STD_DAY Sun // Day of week (1 or Sun, 2 or Mon, 3 or Tue, 4 or Wed, 5 or Thu, 6 or Fri, 7 or Sat)
#define TIME_STD_MONTH Oct // Month (1 or Jan, 2 or Feb, 3 or Mar, 4 or Apr, 5 or May, 6 or Jun, 7 or Jul, 8 or Aug, 9 or Sep, 10 or Oct, 11 or Nov, 12 or Dec)
#define TIME_STD_HOUR 3 // Hour (0 to 23)
#define TIME_STD_OFFSET +60 // Offset from UTC in minutes (-780 to +780)
2018-04-05 14:26:16 +01:00
// -- Location ------------------------------------
#define LATITUDE 48.858360 // [Latitude] Your location to be used with sunrise and sunset
#define LONGITUDE 2.294442 // [Longitude] Your location to be used with sunrise and sunset
2017-01-28 13:41:01 +00:00
// -- Application ---------------------------------
2018-04-05 14:26:16 +01:00
#define APP_TIMEZONE 1 // [Timezone] +1 hour (Amsterdam) (-13 .. 14 = hours from UTC, 99 = use TIME_DST/TIME_STD)
#define APP_LEDSTATE LED_POWER // [LedState] Function of led
// (LED_OFF, LED_POWER, LED_MQTTSUB, LED_POWER_MQTTSUB, LED_MQTTPUB, LED_POWER_MQTTPUB, LED_MQTT, LED_POWER_MQTT)
#define APP_LEDMASK 0xFFFF // [LedMask] Assign Relay to Power led (0xFFFF is default)
#define APP_ENABLE_LEDLINK false // [SetOption31] Enable link led blinking
2017-01-28 13:41:01 +00:00
#define APP_PULSETIME 0 // [PulseTime] Time in 0.1 Sec to turn off power for relay 1 (0 = disabled)
2018-04-05 14:26:16 +01:00
#define APP_POWERON_STATE POWER_ALL_SAVED // [PowerOnState] Power On Relay state
// (POWER_ALL_OFF, POWER_ALL_ON, POWER_ALL_SAVED_TOGGLE, POWER_ALL_SAVED, POWER_ALL_ALWAYS_ON, POWER_ALL_OFF_PULSETIME_ON)
2017-01-28 13:41:01 +00:00
#define APP_BLINKTIME 10 // [BlinkTime] Time in 0.1 Sec to blink/toggle power for relay 1
#define APP_BLINKCOUNT 10 // [BlinkCount] Number of blinks (0 = 32000)
#define APP_BISTABLE_PULSE 40 // [SetOption45] Pulse time in ms for two coil bistable latching relays
#define APP_NORMAL_SLEEP false // [SetOption60] Enable normal sleep instead of dynamic sleep
2019-11-24 18:35:54 +00:00
#define APP_SLEEP 0 // [Sleep] Sleep time to lower energy consumption (0 = Off, 1 - 250 mSec),
#define PWM_MAX_SLEEP 10 // Sleep will be lowered to this value when light is on, to avoid flickering, and when buzzer is on for better on/off period accuracy
2017-01-28 13:41:01 +00:00
#define KEY_DEBOUNCE_TIME 50 // [ButtonDebounce] Number of mSeconds button press debounce time
#define KEY_HOLD_TIME 40 // [SetOption32] Number of 0.1 seconds to hold Button or external Pushbutton before sending HOLD message
#define KEY_DISABLE_MULTIPRESS false // [SetOption1] Disable button multipress
#define KEY_SWAP_DOUBLE_PRESS false // [SetOption11] Swap button single and double press functionality
#define KEY_ONLY_SINGLE_PRESS false // [SetOption13] Enable only single press to speed up button press recognition
2021-03-02 21:47:40 +00:00
#define MQTT_BUTTONS false // [SetOption73] Detach buttons from relays and send multi-press and hold MQTT messages instead
#define SWITCH_DEBOUNCE_TIME 50 // [SwitchDebounce] Number of mSeconds switch press debounce time
2020-01-15 15:12:55 +00:00
#define SWITCH_MODE TOGGLE // [SwitchMode] TOGGLE, FOLLOW, FOLLOW_INV, PUSHBUTTON, PUSHBUTTON_INV, PUSHBUTTONHOLD, PUSHBUTTONHOLD_INV, PUSHBUTTON_TOGGLE, TOGGLEMULTI, FOLLOWMULTI, FOLLOWMULTI_INV (the wall switch state)
2021-03-02 21:47:40 +00:00
#define MQTT_SWITCHES false // [SetOption114] Detach switches from relays and send MQTT messages instead
2017-01-28 13:41:01 +00:00
#define TEMP_CONVERSION false // [SetOption8] Return temperature in (false = Celsius or true = Fahrenheit)
#define PRESSURE_CONVERSION false // [SetOption24] Return pressure in (false = hPa or true = mmHg)
#define TEMP_RESOLUTION 1 // [TempRes] Maximum number of decimals (0 - 3) showing sensor Temperature
#define HUMIDITY_RESOLUTION 1 // [HumRes] Maximum number of decimals (0 - 3) showing sensor Humidity
#define PRESSURE_RESOLUTION 1 // [PressRes] Maximum number of decimals (0 - 3) showing sensor Pressure
#define ENERGY_RESOLUTION 3 // [EnergyRes] Maximum number of decimals (0 - 5) showing energy usage in kWh
#define CALC_RESOLUTION 3 // [CalcRes] Maximum number of decimals (0 - 7) used in commands ADD, SUB, MULT and SCALE
2017-01-28 13:41:01 +00:00
#define APP_FLASH_CYCLE false // [SetOption12] Switch between dynamic or fixed slot flash save location
#define APP_NO_RELAY_SCAN false // [SetOption63] Don't scan relay power state at restart
#define APP_DISABLE_POWERCYCLE false // [SetOption65] Disable fast power cycle detection for device reset
2020-01-21 11:36:44 +00:00
#define DEEPSLEEP_BOOTCOUNT false // [SetOption76] Enable incrementing bootcount when deepsleep is enabled
#define APP_INTERLOCK_MODE false // [Interlock] Relay interlock mode
#define APP_INTERLOCK_GROUP_1 0xFF // [Interlock] Relay bitmask for interlock group 1 (0xFF if undef)
//#define APP_INTERLOCK_GROUP_2 0x00 // [Interlock] Relay bitmask for interlock group 2 (0x00 if undef)
//#define APP_INTERLOCK_GROUP_3 0x00 // [Interlock] Relay bitmask for interlock group 3 (0x00 if undef)
//#define APP_INTERLOCK_GROUP_4 0x00 // [Interlock] Relay bitmask for interlock group 4 (0x00 if undef)
// -- Lights --------------------------------------
2020-01-21 11:36:44 +00:00
#define WS2812_LEDS 30 // [Pixels] Number of WS2812 LEDs to start with (max is 512)
#define LIGHT_MODE true // [SetOption15] Switch between commands PWM or COLOR/DIMMER/CT/CHANNEL
#define LIGHT_CLOCK_DIRECTION false // [SetOption16] Switch WS2812 clock between clockwise or counter-clockwise
#define LIGHT_COLOR_RADIX false // [SetOption17] Switch between decimal or hexadecimal color output (false = hexadecimal, true = decimal)
#define LIGHT_PAIRS_CO2 false // [SetOption18] Enable Pair light signal with CO2 sensor
#define LIGHT_POWER_CONTROL false // [SetOption20] Enable power control in relation to Dimmer/Color/Ct changes
#define LIGHT_CHANNEL_MODE false // [SetOption68] Enable multi-channels PWM instead of Color PWM
#define LIGHT_SLIDER_POWER false // [SetOption77] Do not power off if slider moved to far left
#define LIGHT_ALEXA_CT_RANGE false // [SetOption82] Reduced CT range for Alexa
#define LIGHT_PWM_CT_MODE false // [SetOption92] Set PWM Mode from regular PWM to ColorTemp control (Xiaomi Philips ...) a.k.a. module 48 mode
#define LIGHT_WHITE_BLEND_MODE false // [SetOption105] White Blend Mode - used to be `RGBWWTable` last value `0`, now deprecated in favor of this option
#define LIGHT_VIRTUAL_CT false // [SetOption106] Virtual CT - Creates a virtual White ColorTemp for RGBW lights
#define LIGHT_VIRTUAL_CT_CW false // [SetOption107] Virtual CT Channel - signals whether the hardware white is cold CW (true) or warm WW (false)
2020-12-29 18:31:27 +00:00
#define LIGHT_VIRTUAL_CT_POINTS 3 // Number of reference points for Virtual CT (min 2, default 3)
#define USE_AC_ZERO_CROSS_DIMMER // Requires USE_COUNTER and USE_LIGHT
// -- Energy --------------------------------------
#define ENERGY_VOLTAGE_ALWAYS false // [SetOption21] Enable show voltage even if powered off
#define ENERGY_DDS2382_MODE false // [SetOption71] Enable DDS2382 different Modbus registers for Active Energy (#6531)
2020-01-21 11:36:44 +00:00
#define ENERGY_HARDWARE_TOTALS false // [SetOption72] Enable hardware energy total counter as reference (#6561)
// -- Other Options -------------------------------
2020-01-21 11:36:44 +00:00
#define TIMERS_ENABLED false // [Timers] Enable Timers
#define RF_DATA_RADIX false // [SetOption28] RF receive data format (false = hexadecimal, true = decimal)
#define IR_DATA_RADIX false // [SetOption29] IR receive data format (false = hexadecimal, true = decimal)
#define TUYA_SETOPTION_20 false // [SetOption54] Apply SetOption20 settings to Tuya device
2021-11-29 18:27:09 +00:00
#define TUYA_ALLOW_DIMMER_0 false // [SetOption131] Allow save dimmer = 0 receved by MCU
#define TUYA_TEMP_SET_RES 1 // [TuyaTempSetRes] Maximum number of decimals (0 - 3) showing sensor TemperatureSet
#define TUYA_SETOPTION_137 false // [SetOption137] Avoid mqtt-publish of Tuya MCU heartbeat responses
#define IR_ADD_RAW_DATA false // [SetOption58] Add IR Raw data to JSON message
#define BUZZER_ENABLE false // [SetOption67] Enable buzzer when available
#define DS18X20_PULL_UP false // [SetOption74] Enable internal pullup for single DS18x20 sensor
#define COUNTER_RESET false // [SetOption79] Enable resetting of counters after telemetry was sent
#define SHUTTER_SUPPORT false // [SetOption80] Enable shutter support
#define PCF8574_INVERT_PORTS false // [SetOption81] Invert all ports on PCF8574 devices
#define ZIGBEE_FRIENDLY_NAMES false // [SetOption83] Enable Zigbee FriendlyNames instead of ShortAddresses when possible
2021-03-02 21:47:40 +00:00
#define ZIGBEE_DISTINCT_TOPICS false // [SetOption89] Enable unique device topic based on Zigbee device ShortAddr
#define ZIGBEE_RMV_ZBRECEIVED false // [SetOption100] Remove ZbReceived form JSON message
#define ZIGBEE_INDEX_EP false // [SetOption101] Add the source endpoint as suffix to attributes, ex `Power3` instead of `Power` if sent from endpoint 3
2022-09-19 15:19:43 +01:00
#define ZIGBEE_TOPIC_FNAME false // [SetOption112] Enable friendly name in Zigbee topic (use with ZIGBEE_DISTINCT_TOPICS)
2018-04-05 14:26:16 +01:00
/*********************************************************************************************\
* END OF SECTION 1
*
* SECTION 2
* - Enable a feature by removing both // in front of it
* - Disable a feature by preceding it with //
\*********************************************************************************************/
// -- Localization --------------------------------
// If non selected the default en-GB will be used
2020-12-27 20:30:06 +00:00
//#define MY_LANGUAGE af_AF // Afrikaans in South Africa
//#define MY_LANGUAGE bg_BG // Bulgarian in Bulgaria
//#define MY_LANGUAGE ca_AD // Catalan in All catalan speaking countries ( Andorra )
//#define MY_LANGUAGE cs_CZ // Czech in Czech
//#define MY_LANGUAGE de_DE // German in Germany
//#define MY_LANGUAGE el_GR // Greek in Greece
//#define MY_LANGUAGE en_GB // English in Great Britain. Enabled by Default
//#define MY_LANGUAGE es_ES // Spanish in Spain
//#define MY_LANGUAGE fr_FR // French in France
//#define MY_LANGUAGE fy_NL // Frysk in Nederland
//#define MY_LANGUAGE he_HE // Hebrew in Israel
//#define MY_LANGUAGE hu_HU // Hungarian in Hungary
//#define MY_LANGUAGE it_IT // Italian in Italy
//#define MY_LANGUAGE ko_KO // Korean in Korea
//#define MY_LANGUAGE nl_NL // Dutch in the Nederland
//#define MY_LANGUAGE pl_PL // Polish in Poland
//#define MY_LANGUAGE pt_BR // Portuguese in Brazil
//#define MY_LANGUAGE pt_PT // Portuguese in Portugal
//#define MY_LANGUAGE ro_RO // Romanian in Romania
//#define MY_LANGUAGE ru_RU // Russian in Russia
//#define MY_LANGUAGE sk_SK // Slovak in Slovakia
//#define MY_LANGUAGE sv_SE // Swedish in Sweden
//#define MY_LANGUAGE tr_TR // Turkish in Turkey
//#define MY_LANGUAGE uk_UA // Ukrainian in Ukraine
2020-10-12 10:53:18 +01:00
//#define MY_LANGUAGE vi_VN // Vietnamese in Vietnam
//#define MY_LANGUAGE zh_CN // Chinese (Simplified) in China
//#define MY_LANGUAGE zh_TW // Chinese (Traditional) in Taiwan
2018-04-05 14:26:16 +01:00
// -- Wifi Config tools ---------------------------
#define WIFI_SOFT_AP_CHANNEL 1 // Soft Access Point Channel number between 1 and 13 as used by Wi-Fi Manager web GUI
#define USE_IMPROV // Add support for IMPROV serial protocol as used by esp-web-tools (+2k code)
2022-12-10 12:44:16 +00:00
// -- IPv6 support -------------------------------
// #define USE_IPV6 // Enable IPv6 support (if the underlying esp-idf is also configured to support it)
// Code size increase: ESP8266: +34.5kb
// Enabled by default on ESP32 and variants
2022-12-10 12:44:16 +00:00
2021-07-02 13:12:49 +01:00
// -- ESP-NOW -------------------------------------
//#define USE_TASMESH // Enable Tasmota Mesh using ESP-NOW (+11k code)
// -- OTA -----------------------------------------
//#define USE_ARDUINO_OTA // Add optional support for Arduino OTA with ESP8266 (+13k code)
// -- Influxdb ------------------------------------
//#define USE_INFLUXDB // Enable influxdb support (+5k code)
// #define INFLUXDB_STATE 0 // [Ifx] Influxdb initially Off (0) or On (1)
// #define INFLUXDB_VERSION 1 // Version of Influxdb 1 or 2
// #define INFLUXDB_HOST "influxdb" // [IfxHost] Influxdb hostname or IP address
// #define INFLUXDB_PORT 8086 // [IfxPort] Influxdb port number
// #define INFLUXDB_ORG "" // [IfxUser, IfxOrg] Influxdb v1 username or v2 organisation
// #define INFLUXDB_TOKEN "" // [IfxPassword, IfxToken] Influxdb v1 password or v2 token
// #define INFLUXDB_BUCKET "db" // [IfxDatabase, IfxBucket] Influxdb v1 database or v2 bucket
2022-05-03 20:22:51 +01:00
// #define INFLUXDB_RP "" // [IfxRP] Influxdb retention policy
// -- MQTT ----------------------------------------
#define MQTT_LWT_OFFLINE "Offline" // MQTT LWT offline topic message
#define MQTT_LWT_ONLINE "Online" // MQTT LWT online topic message
#define MQTT_TELE_RETAIN 0 // Tele messages may send retain flag (0 = off, 1 = on)
#define MQTT_CLEAN_SESSION 1 // Mqtt clean session connection (0 = No clean session, 1 = Clean session (default))
#define MQTT_DISABLE_SSERIALRECEIVED 0 // 1 = Disable sserialreceived mqtt messages, 0 = Enable sserialreceived mqtt messages (default)
2018-04-05 14:26:16 +01:00
// -- MQTT - Domoticz -----------------------------
#define USE_DOMOTICZ // Enable Domoticz (+6k code, +0.3k mem)
#define DOMOTICZ_IN_TOPIC "domoticz/in" // Domoticz Input Topic
#define DOMOTICZ_OUT_TOPIC "domoticz/out" // Domoticz Output Topic
// -- MQTT - Home Assistant Discovery -------------
//#define USE_HOME_ASSISTANT // Enable Home Assistant Discovery Support (+12k code, +6 bytes mem)
// #define HOME_ASSISTANT_DISCOVERY_PREFIX "homeassistant" // Home Assistant discovery prefix
// #define HOME_ASSISTANT_LWT_TOPIC "homeassistant/status" // home Assistant Birth and Last Will Topic (default = homeassistant/status)
// #define HOME_ASSISTANT_LWT_SUBSCRIBE true // Subscribe to Home Assistant Birth and Last Will Topic (default = true)
2018-04-05 14:26:16 +01:00
// -- MQTT - Tasmota Discovery ---------------------
#define USE_TASMOTA_DISCOVERY // Enable Tasmota Discovery support (+2k code)
// -- MQTT - TLS - AWS IoT ------------------------
// Using TLS starting with version v6.5.0.16 compilation will only work using Core 2.4.2 and 2.5.2. No longer supported: 2.3.0
//#define USE_MQTT_TLS // Use TLS for MQTT connection (+34.5k code, +7.0k mem and +4.8k additional during connection handshake)
// #define USE_MQTT_TLS_CA_CERT // [DEPRECATED] Now TLS supports dual mode using SetOption132 - this flag is now ignored
// #define USE_MQTT_AWS_IOT_LIGHT // Enable MQTT for AWS IoT in light mode, with user/password instead of private certificate
// #define USE_MQTT_AWS_IOT // [Deprecated] Enable MQTT for AWS IoT - requires a private key (+11.9k code, +0.4k mem)
2019-10-27 11:04:08 +00:00
// Note: you need to generate a private key + certificate per device and update 'tasmota/tasmota_aws_iot.cpp'
// Full documentation here: https://github.com/arendst/Tasmota/wiki/AWS-IoT
// #define USE_MQTT_TLS_DROP_OLD_FINGERPRINT // If you use fingerprint (i.e. not CA) validation, the algorithm changed to a more secure one.
// Any valid fingerprint with the old algo will be automatically updated to the new algo.
// Enable this if you want to disable the old algo check, which should be more secure
2020-11-14 18:19:45 +00:00
// for USE_4K_RSA (support for 4096 bits certificates, instead of 2048), you need to uncommend `-DUSE_4K_RSA` in `build_flags` from `platform.ini` or `platform_override.ini`
// -- MQTT - TLS - Azure IoT & IoT Central ---------
// Starting with version v9.4.0.3 added support for both Azure IoT Hub and IoT Central
//#define USE_MQTT_TLS // REQUIRED Use TLS for MQTT connection (+34.5k code, +7.0k mem and +4.8k additional during connection handshake)
// #define USE_MQTT_AZURE_IOT // REQUIRED Enable accesss to IoT Hub without DPS using a preshared key: https://tasmota.github.io/docs/Azure-IoT-Hub/ Enable MQTT for Azure IoT Hub (+1k code)
// #define USE_MQTT_AZURE_DPS_SCOPEID // OPTIONAL Enables Azure Device Provisioning Service (DPS) for provision at scale, REQUIRED for IoT Central. Uses the REST over HTTPS protocol (+4k memory)
// #define USE_MQTT_AZURE_DPS_PRESHAREDKEY // OPTIONAL The Preshared Key of DPS https://github.com/tasmota/docs/blob/development/docs/Azure-IoT-Central.md
// #define USE_MQTT_AZURE_DPS_SCOPE_ENDPOINT // OPTIONAL Defaults to "https://global.azure-devices-provisioning.net/", can be changed for Azure China, Azure Germany or others.
2019-06-05 10:44:52 +01:00
// -- Telegram Protocol ---------------------------
//#define USE_TELEGRAM // Support for Telegram protocol (+49k code, +7.0k mem and +4.8k additional during connection handshake)
#define USE_TELEGRAM_FINGERPRINT "\xB2\x72\x47\xA6\x69\x8C\x3C\x69\xF9\x58\x6C\xF3\x60\x02\xFB\x83\xFA\x8B\x1F\x23" // Telegram api.telegram.org TLS public key fingerpring
// -- KNX IP Protocol -----------------------------
2018-07-23 04:54:25 +01:00
//#define USE_KNX // Enable KNX IP Protocol Support (+9.4k code, +3k7 mem)
#define USE_KNX_WEB_MENU // Enable KNX WEB MENU (+8.3k code, +144 mem)
2018-04-05 14:26:16 +01:00
// -- HTTP ----------------------------------------
#define USE_WEBSERVER // Enable web server and Wi-Fi Manager (+66k code, +8k mem)
2018-04-05 14:26:16 +01:00
#define WEB_PORT 80 // Web server Port for User and Admin mode
#define WEB_USERNAME "admin" // Web server Admin mode user name
2021-09-01 01:22:05 +01:00
// #define DISABLE_REFERER_CHK // [SetOption128] Disable HTTP API
#define USE_ENHANCED_GUI_WIFI_SCAN // Enable Wi-Fi scan output with BSSID (+0k5 code)
// #define USE_WEBSEND_RESPONSE // Enable command WebSend response message (+1k code)
// #define USE_WEBGETCONFIG // Enable restoring config from external webserver (+0k6)
2024-01-08 08:40:10 +00:00
// #define USE_GPIO_VIEWER // Enable GPIO Viewer to see realtime GPIO states (+4k code)
2024-01-12 11:17:31 +00:00
// #define GV_BASE_URL "https://thelastoutpostworkshop.github.io/microcontroller_devkit/gpio_viewer/assets/"
// #define GV_SAMPLING_INTERVAL 100 // [GvSampling] milliseconds - Use Tasmota Scheduler (100) or Ticker (20..99,101..1000)
#define USE_EMULATION_HUE // Enable Hue Bridge emulation for Alexa (+14k code, +2k mem common)
#define USE_EMULATION_WEMO // Enable Belkin WeMo emulation for Alexa (+6k code, +2k mem common)
2020-11-24 19:29:28 +00:00
// #define USE_CCLOADER // Enable CCLoader FW upgrade tool (for CC25xx devices)
2018-04-05 14:26:16 +01:00
// -- mDNS ----------------------------------------
//#define USE_DISCOVERY // Enable mDNS for the following services (+8k code or +23.5k code with core 2_5_x, +0.3k mem)
2018-04-05 14:26:16 +01:00
#define WEBSERVER_ADVERTISE // Provide access to webserver by name <Hostname>.local/
2022-11-23 20:57:40 +00:00
// #define MQTT_HOST_DISCOVERY // Find MQTT host server (overrides MQTT_HOST if found) - disabled by default because it causes blocked repeated 3000ms pauses
2018-04-05 14:26:16 +01:00
// -- Time ----------------------------------------
#define USE_TIMERS // Add support for up to 16 timers (+2k2 code)
#define USE_TIMERS_WEB // Add timer webpage support (+4k5 code)
#define USE_SUNRISE // Add support for Sunrise and sunset tools (+16k)
#define SUNRISE_DAWN_ANGLE DAWN_NORMAL // Select desired Dawn Angle from (DAWN_NORMAL, DAWN_CIVIL, DAWN_NAUTIC, DAWN_ASTRONOMIC)
2018-04-05 14:26:16 +01:00
2020-04-10 19:51:15 +01:00
// -- Ping ----------------------------------------
2020-04-15 17:55:04 +01:00
// #define USE_PING // Enable Ping command (+2k code)
2020-04-10 19:51:15 +01:00
// -- Compression ---------------------------------
#define USE_UNISHOX_COMPRESSION // Add support for string compression in Rules or Scripts
// -- Rules or Script ----------------------------
// Select none or only one of the below defines USE_RULES or USE_SCRIPT
2019-07-09 09:48:03 +01:00
#define USE_RULES // Add support for rules (+8k code)
2022-10-04 17:29:54 +01:00
// #define USE_EXPRESSION // Add support for expression evaluation in rules (+3k2 code, +64 bytes mem)
// #define SUPPORT_IF_STATEMENT // Add support for IF statement in rules (+4k2 code, -332 bytes mem)
// #define USER_RULE1 "<Any rule1 data>" // Add rule1 data saved at initial firmware load or when command reset is executed
// #define USER_RULE2 "<Any rule2 data>" // Add rule2 data saved at initial firmware load or when command reset is executed
// #define USER_RULE3 "<Any rule3 data>" // Add rule3 data saved at initial firmware load or when command reset is executed
2019-07-09 09:48:03 +01:00
//#define USE_SCRIPT // Add support for script (+17k code)
// #define USE_SCRIPT_FATFS 4 // Script: Add FAT FileSystem Support
// #define SUPPORT_MQTT_EVENT // Support trigger event with MQTT subscriptions (+3k5 code)
//#define USER_BACKLOG "<Any command separated by a semicolon (;)>" // Add commands executed at firmware load or when command reset is executed
2021-03-20 17:44:35 +00:00
// -- Optional modules ----------------------------
#define ROTARY_V1 // Add support for Rotary Encoder as used in MI Desk Lamp (+0k8 code)
#define ROTARY_MAX_STEPS 10 // Rotary step boundary
#define USE_SONOFF_RF // Add support for Sonoff Rf Bridge (+3k2 code)
#define USE_RF_FLASH // Add support for flashing the EFM8BB1 chip on the Sonoff RF Bridge. C2CK must be connected to GPIO4, C2D to GPIO5 on the PCB (+2k7 code)
#define USE_SONOFF_SC // Add support for Sonoff Sc (+1k1 code)
#define USE_TUYA_MCU // Add support for Tuya Serial MCU
#define TUYA_DIMMER_ID 0 // Default dimmer Id
#define USE_TUYA_TIME // Add support for Set Time in Tuya MCU
2023-01-08 16:51:17 +00:00
//#define USE_TUYAMCUBR // Add support for TuyaMCU Bridge
#define USE_ARMTRONIX_DIMMERS // Add support for Armtronix Dimmers (+1k4 code)
2019-10-17 11:20:26 +01:00
#define USE_PS_16_DZ // Add support for PS-16-DZ Dimmer (+2k code)
#define USE_SONOFF_IFAN // Add support for Sonoff iFan02 and iFan03 (+2k code)
#define USE_BUZZER // Add support for a buzzer (+0k6 code)
#define USE_ARILUX_RF // Add support for Arilux RF remote controller (+0k8 code, 252 iram (non 2.3.0))
#define USE_SHUTTER // Add Shutter support for up to 4 shutter with different motortypes (+11k code)
#define USE_DEEPSLEEP // Add support for deepsleep (+1k code)
#define USE_EXS_DIMMER // Add support for ES-Store Wi-Fi Dimmer (+1k5 code)
// #define EXS_MCU_CMNDS // Add command to send MCU commands (+0k8 code)
2019-12-30 13:23:37 +00:00
//#define USE_HOTPLUG // Add support for sensor HotPlug
#define USE_DEVICE_GROUPS // Add support for device groups (+5k5 code)
#define DEVICE_GROUPS_ADDRESS 239,255,250,250 // Device groups multicast address
#define DEVICE_GROUPS_PORT 4447 // Device groups multicast port
2020-04-26 17:04:12 +01:00
#define USE_DEVICE_GROUPS_SEND // Add support for the DevGroupSend command (+0k6 code)
#define USE_PWM_DIMMER // Add support for MJ-SD01/acenx/NTONPOWER PWM dimmers (+2k3 code, DGR=0k7)
#define USE_PWM_DIMMER_REMOTE // Add support for remote switches to PWM Dimmer (requires USE_DEVICE_GROUPS) (+0k6 code)
//#define USE_KEELOQ // Add support for Jarolift rollers by Keeloq algorithm (+4k5 code)
#define USE_SONOFF_D1 // Add support for Sonoff D1 Dimmer (+0k7 code)
#define USE_SHELLY_DIMMER // Add support for Shelly Dimmer (+3k code)
#define SHELLY_CMDS // Add command to send co-processor commands (+0k3 code)
#define SHELLY_FW_UPGRADE // Add firmware upgrade option for co-processor (+3k4 code)
2020-11-18 07:47:23 +00:00
// #define SHELLY_VOLTAGE_MON // Add support for reading voltage and current measurment (-0k0 code)
//#define USE_MAGIC_SWITCH // Add Sonoff MagicSwitch support as implemented in Sonoff Basic R4 (+612B flash, +64B IRAM for intr)
// #define MAGICSWITCH_MIN_PULSE 4000 // Overridable minimum pulse, also overridable by command MagicSwitchPulse (not saved to flash)
// #define MAGICSWITCH_MASKING_WINDOW_LEN 5 // Overridable masking window (in number of 50ms loops)
// -- Optional light modules ----------------------
#define USE_LIGHT // Add support for light control
#define USE_WS2812 // WS2812 Led string using library NeoPixelBus (+5k code, +1k mem, 232 iram) - Disable by //
// #define USE_WS2812_DMA // ESP8266 only, DMA supports only GPIO03 (= Serial RXD) (+1k mem). When USE_WS2812_DMA is enabled expect Exceptions on Pow
#define USE_WS2812_RMT 0 // ESP32 only, hardware RMT support (default). Specify the RMT channel 0..7. This should be preferred to software bit bang.
// #define USE_WS2812_I2S 0 // ESP32 only, hardware I2S support. Specify the I2S channel 0..2. This is exclusive from RMT. By default, prefer RMT support
// #define USE_WS2812_INVERTED // Use inverted data signal
#define USE_WS2812_HARDWARE NEO_HW_WS2812 // Hardware type (NEO_HW_WS2812, NEO_HW_WS2812X, NEO_HW_WS2813, NEO_HW_SK6812, NEO_HW_LC8812, NEO_HW_APA106, NEO_HW_P9813)
#define USE_WS2812_CTYPE NEO_GRB // Color type (NEO_RGB, NEO_GRB, NEO_BRG, NEO_RBG, NEO_RGBW, NEO_GRBW)
#define USE_MY92X1 // Add support for MY92X1 RGBCW led controller as used in Sonoff B1, Ailight and Lohas
#define USE_SM16716 // Add support for SM16716 RGB LED controller (+0k7 code)
#define USE_SM2135 // Add support for SM2135 RGBCW led control as used in Action LSC (+0k6 code)
#define USE_SM2335 // Add support for SM2335 RGBCW led control as used in SwitchBot Color Bulb (+0k7 code)
#define USE_BP1658CJ // Add support for BP1658CJ RGBCW led control as used in Orein OS0100411267 Bulb
2022-05-30 10:34:29 +01:00
#define USE_BP5758D // Add support for BP5758D RGBCW led control as used in some Tuya lightbulbs (+0k8 code)
2019-10-17 11:20:26 +01:00
#define USE_SONOFF_L1 // Add support for Sonoff L1 led control
#define USE_ELECTRIQ_MOODL // Add support for ElectriQ iQ-wifiMOODL RGBW LED controller (+0k3 code)
2020-04-13 23:55:12 +01:00
#define USE_LIGHT_PALETTE // Add support for color palette (+0k7 code)
2020-12-29 18:31:27 +00:00
#define USE_LIGHT_VIRTUAL_CT // Add support for Virtual White Color Temperature (+1.1k code)
2020-04-25 23:49:34 +01:00
#define USE_DGR_LIGHT_SEQUENCE // Add support for device group light sequencing (requires USE_DEVICE_GROUPS) (+0k2 code)
//#define USE_LSC_MCSL // Add support for GPE Multi color smart light as sold by Action in the Netherlands (+1k1 code)
2022-11-16 09:55:56 +00:00
// #define USE_LIGHT_ARTNET // Add support for DMX/ArtNet via UDP on port 6454 (+3.5k code)
#define USE_LIGHT_ARTNET_MCAST 239,255,25,54 // Multicast address used to listen: 239.255.25.54
// -- Counter input -------------------------------
#define USE_COUNTER // Enable inputs as counter (+0k8 code)
// -- Internal Analog input -----------------------
//#define USE_ADC_VCC // Display Vcc in Power status. Disable for use as Analog input on selected devices
// -- One wire sensors ----------------------------
#define USE_DS18x20 // Add support for DS18x20 sensors with id sort, single scan and read retry (+2k6 code)
2019-09-25 15:28:54 +01:00
// #define W1_PARASITE_POWER // Optimize for parasite powered sensors
// #define DS18x20_USE_ID_AS_NAME // Use last 3 bytes for naming of sensors
2022-10-15 16:40:17 +01:00
// #define DS18x20_USE_ID_ALIAS // Add support aliasing for DS18x20 sensors. See comments in xsns_05 files (+0k5 code)
2017-01-28 13:41:01 +00:00
// -- I2C sensors ---------------------------------
#define USE_I2C // I2C using library wire (+10k code, 0k2 mem, 124 iram)
2021-03-02 21:47:40 +00:00
#define I2CDRIVERS_0_31 0xFFFFFFFF // Enable I2CDriver0 to I2CDriver31
#define I2CDRIVERS_32_63 0xFFFFFFFF // Enable I2CDriver32 to I2CDriver63
#define I2CDRIVERS_64_95 0xFFFFFFFF // Enable I2CDriver64 to I2CDriver95
#ifdef USE_I2C
// #define USE_SHT // [I2cDriver8] Enable SHT1X sensor (+1k4 code)
// #define USE_HTU // [I2cDriver9] Enable HTU21/SI7013/SI7020/SI7021 sensor (I2C address 0x40) (+1k5 code)
// #define USE_BMP // [I2cDriver10] Enable BMP085/BMP180/BMP280/BME280 sensors (I2C addresses 0x76 and 0x77) (+4k4 code)
// #define USE_BME68X // Enable support for BME680/BME688 sensor using Bosch BME68x library (+6k9 code)
// #define USE_BH1750 // [I2cDriver11] Enable BH1750 sensor (I2C address 0x23 or 0x5C) (+0k5 code)
// #define USE_VEML6070 // [I2cDriver12] Enable VEML6070 sensor (I2C addresses 0x38 and 0x39) (+1k5 code)
#define USE_VEML6070_RSET 270000 // VEML6070, Rset in Ohm used on PCB board, default 270K = 270000ohm, range for this sensor: 220K ... 1Meg
#define USE_VEML6070_SHOW_RAW // VEML6070, shows the raw value of UV-A
// #define USE_ADS1115 // [I2cDriver13] Enable ADS1115 16 bit A/D converter (I2C address 0x48, 0x49, 0x4A or 0x4B) based on Adafruit ADS1x15 library (no library needed) (+0k7 code)
// #define USE_INA219 // [I2cDriver14] Enable INA219 (I2C address 0x40, 0x41 0x44 or 0x45) Low voltage and current sensor (+1k code)
2022-10-15 23:03:07 +01:00
// #define INA219_SHUNT_RESISTOR (0.100) // 0.1 Ohm default shunt resistor, can be overriden in user_config_override or using Sensor13
// #define USE_INA226 // [I2cDriver35] Enable INA226 (I2C address 0x40, 0x41 0x44 or 0x45) Low voltage and current sensor (+2k3 code)
// #define USE_SHT3X // [I2cDriver15] Enable SHT3x (I2C address 0x44 or 0x45) or SHTC3 (I2C address 0x70) sensor (+0k7 code)
// #define USE_TSL2561 // [I2cDriver16] Enable TSL2561 sensor (I2C address 0x29, 0x39 or 0x49) using library Joba_Tsl2561 (+2k3 code)
// #define USE_TSL2591 // [I2cDriver40] Enable TSL2591 sensor (I2C address 0x29) using library Adafruit_TSL2591 (+1k6 code)
// #define USE_MGS // [I2cDriver17] Enable Xadow and Grove Mutichannel Gas sensor using library Multichannel_Gas_Sensor (+10k code)
#define MGS_SENSOR_ADDR 0x04 // Default Mutichannel Gas sensor i2c address
// #define USE_SGP30 // [I2cDriver18] Enable SGP30 sensor (I2C address 0x58) (+1k1 code)
2022-08-25 20:51:51 +01:00
// #define USE_SGP40 // [I2cDriver69] Enable SGP40 sensor (I2C address 0x59) (+1k4 code)
2023-06-29 13:10:49 +01:00
// #define USE_SGP4X // [I2cDriver82] Enable SGP41 sensor (I2C address 0x59) (+7k2 code)
2023-01-29 07:06:25 +00:00
// #define USE_SEN5X // [I2cDriver76] Enable SEN5X sensor (I2C address 0x69) (+3k code)
// #define USE_SI1145 // [I2cDriver19] Enable SI1145/46/47 sensor (I2C address 0x60) (+1k code)
// #define USE_LM75AD // [I2cDriver20] Enable LM75AD sensor (I2C addresses 0x48 - 0x4F) (+0k5 code)
// #define USE_APDS9960 // [I2cDriver21] Enable APDS9960 Proximity Sensor (I2C address 0x39). Disables SHT and VEML6070 (+4k7 code)
#define USE_APDS9960_GESTURE // Enable APDS9960 Gesture feature (+2k code)
#define USE_APDS9960_PROXIMITY // Enable APDS9960 Proximity feature (>50 code)
#define USE_APDS9960_COLOR // Enable APDS9960 Color feature (+0.8k code)
#define USE_APDS9960_STARTMODE 0 // Default to enable Gesture mode
// #define USE_MCP230xx // [I2cDriver22] Enable MCP23008/MCP23017 - Must define I2C Address in #define USE_MCP230xx_ADDR below - range 0x20 - 0x27 (+5k1 code)
// #define USE_MCP230xx_ADDR 0x20 // Enable MCP23008/MCP23017 I2C Address to use (Must be within range 0x20 through 0x26 - set according to your wired setup)
// #define USE_MCP230xx_OUTPUT // Enable MCP23008/MCP23017 OUTPUT support through sensor29 commands (+2k2 code)
// #define USE_MCP230xx_DISPLAYOUTPUT // Enable MCP23008/MCP23017 to display state of OUTPUT pins on Web UI (+0k2 code)
// #define USE_MCP23XXX_DRV // [I2cDriver77] Enable MCP23xxx support as virtual switch/button/relay (+3k(I2C)/+5k(SPI) code)
// #define USE_PCA9685 // [I2cDriver1] Enable PCA9685 I2C HW PWM Driver - Must define I2C Address in #define USE_PCA9685_ADDR below - range 0x40 - 0x47 (+1k4 code)
2023-07-24 14:30:48 +01:00
// #define USE_PCA9685_V2 // [I2cDriver1] Enable PCA9685 I2C HW PWM Driver - Must define I2C Address in #define USE_PCA9685_ADDR below - range 0x40 - 0x47 (+3k4 code)
// #define USE_PCA9685_ADDR 0x40 // Enable PCA9685 I2C Address to use (Must be within range 0x40 through 0x47 - set according to your wired setup)
// #define USE_PCA9685_FREQ 50 // Define default PWM frequency in Hz to be used (must be within 24 to 1526) - If other value is used, it will rever to 50Hz
// #define USE_PCA9632 // [I2cDriver75] Enable PCA9632 I2C HW PWM Driver (+1k8 code)
// #define USE_PCA9632_ADDR 0x60 // Define PCA9685 I2C Address to use (Must be within range 0x60 through 0x63 - set according to your wired setup)
// #define USE_PCA9632_CM_0 0 // Mapping for channel 0
// #define USE_PCA9632_CM_1 1 // Mapping for channel 1
// #define USE_PCA9632_CM_2 2 // Mapping for channel 2
// #define USE_PCA9632_CM_3 3 // Mapping for channel 3
// #define USE_MPR121 // [I2cDriver23] Enable MPR121 controller (I2C addresses 0x5A, 0x5B, 0x5C and 0x5D) in input mode for touch buttons (+1k3 code)
// #define USE_CCS811 // [I2cDriver24] Enable CCS811 sensor (I2C address 0x5A) (+2k2 code)
// #define USE_CCS811_V2 // [I2cDriver24] Enable CCS811 sensor (I2C addresses 0x5A and 0x5B) (+2k8 code)
// #define USE_ENS16x // [I2cDriver85] Enable ENS160 and ENS161 sensor (I2C addresses 0x52 and 0x53) (+1.9kB of code and 12B of RAM)
// #define USE_ENS210 // [I2cDriver86] Enable ENS210 sensor (I2C addresses 0x43) (+1.7kB of code and 12B of RAM)
// #define USE_MPU6050 // [I2cDriver25] Enable MPU6050 sensor (I2C address 0x68 AD0 low or 0x69 AD0 high) (+3K3 of code and 188 Bytes of RAM)
// #define USE_MPU6050_DMP // Enable in MPU6050 to use the DMP on the chip, should create better results (+8k6 of code)
// #define USE_MGC3130 // [I2cDriver27] Enable MGC3130 Electric Field Effect Sensor (I2C address 0x42) (+2k7 code, 0k3 mem)
// #define USE_MAX44009 // [I2cDriver28] Enable MAX44009 Ambient Light sensor (I2C addresses 0x4A and 0x4B) (+0k8 code)
// #define USE_SCD30 // [I2cDriver29] Enable Sensiron SCd30 CO2 sensor (I2C address 0x61) (+3k3 code)
// #define USE_SCD40 // [I2cDriver62] Enable Sensiron SCd40/Scd41 CO2 sensor (I2C address 0x62) (+3k5 code)
// #define USE_SPS30 // [I2cDriver30] Enable Sensiron SPS30 particle sensor (I2C address 0x69) (+1.7 code)
2022-03-11 15:54:57 +00:00
// #define USE_ADE7880 // [I2cDriver65] Enable ADE7880 Energy monitor as used on Shelly 3EM (I2C address 0x38) (+3k8)
#define USE_ADE7953 // [I2cDriver7] Enable ADE7953 Energy monitor as used on Shelly 2.5 (I2C address 0x38) (+1k5)
// #define USE_VL53L0X // [I2cDriver31] Enable VL53L0x time of flight sensor (I2C address 0x29) (+4k code)
2022-03-11 22:12:57 +00:00
// #define VL53L0X_XSHUT_ADDRESS 0x78 // VL53L0X base address when used with XSHUT control
// #define USE_VL53L1X // [I2cDriver54] Enable VL53L1X time of flight sensor (I2C address 0x29) using Pololu VL53L1X library (+2k9 code)
2022-03-11 22:12:57 +00:00
// #define VL53L1X_XSHUT_ADDRESS 0x78 // VL53L1X base address when used with XSHUT control
2022-03-11 21:02:32 +00:00
// #define VL53L1X_DISTANCE_MODE Long // VL53L1X distance mode : Long | Medium | Short
// #define USE_TOF10120 // [I2cDriver57] Enable TOF10120 time of flight sensor (I2C address 0x52) (+0k6 code)
// #define USE_MLX90614 // [I2cDriver32] Enable MLX90614 ir temp sensor (I2C address 0x5a) (+0.6k code)
// #define USE_CHIRP // [I2cDriver33] Enable CHIRP soil moisture sensor (variable I2C address, default 0x20)
// #define USE_PAJ7620 // [I2cDriver34] Enable PAJ7620 gesture sensor (I2C address 0x73) (+2.5k code)
2023-03-27 14:42:40 +01:00
// #define USE_PCF8574 // [I2cDriver2] Enable PCF8574 I/O Expander (I2C addresses 0x20 - 0x26 and 0x39 - 0x3F) (+2k1 code)
// #define USE_PCF8574_MODE2 // Enable Mode2 virtual relays/buttons/switches (+2k3 code)
// #define USE_PCF8574_SENSOR // Enable Mode1 inputs and outputs in SENSOR message (+0k2 code)
// #define USE_PCF8574_DISPLAYINPUT // Enable Mode1 inputs display in Web page (+0k2 code)
// #define USE_PCF8574_MQTTINPUT // Enable Mode1 MQTT message & rule process on input change detection : stat/%topic%/PCF8574_INP = {"Time":"2021-03-07T16:19:23+01:00","PCF8574-1_INP":{"D1":1}} (+0k5 code)
// #define PCF8574_ADDR1 0x20 // First address to search for PCF8574
// #define PCF8574_ADDR1_COUNT 7 // Number of addresses to search for PCF8574 - Default to 0x20 to 0x26
// #define PCF8574_ADDR2 0x39 // First address to search for PCF8574A
// #define PCF8574_ADDR2_COUNT 6 // Number of addresses to search for PCF8574A - Default to 0x39 to 0x3E
// #define USE_HIH6 // [I2cDriver36] Enable Honeywell HIH Humidity and Temperature sensor (I2C address 0x27) (+0k6)
2019-12-17 21:29:16 +00:00
// #define USE_DHT12 // [I2cDriver41] Enable DHT12 humidity and temperature sensor (I2C address 0x5C) (+0k7 code)
2019-12-28 10:35:44 +00:00
// #define USE_DS1624 // [I2cDriver42] Enable DS1624, DS1621 temperature sensor (I2C addresses 0x48 - 0x4F) (+1k2 code)
// #define USE_AHT1x // [I2cDriver43] Enable AHT10/15 humidity and temperature sensor (I2C address 0x38, 0x39) (+0k8 code)
2022-02-05 17:26:37 +00:00
// #define USE_AHT2x // [I2cDriver43] Enable AHT20/AM2301B instead of AHT1x humidity and temperature sensor (I2C address 0x38) (+0k8 code)
// #define USE_WEMOS_MOTOR_V1 // [I2cDriver44] Enable Wemos motor driver V1 (I2C addresses 0x2D - 0x30) (+0k7 code)
// #define WEMOS_MOTOR_V1_ADDR 0x30 // Default I2C address 0x30
// #define WEMOS_MOTOR_V1_FREQ 1000 // Default frequency
// #define USE_HDC1080 // [I2cDriver45] Enable HDC1080 temperature/humidity sensor (I2C address 0x40) (+1k5 code)
// #define USE_IAQ // [I2cDriver46] Enable iAQ-core air quality sensor (I2C address 0x5a) (+0k6 code)
// #define USE_AS3935 // [I2cDriver48] Enable AS3935 Franklin Lightning Sensor (I2C address 0x03) (+5k4 code)
// #define USE_VEML6075 // [I2cDriver49] Enable VEML6075 UVA/UVB/UVINDEX Sensor (I2C address 0x10) (+2k1 code)
// #define USE_VEML7700 // [I2cDriver50] Enable VEML7700 Ambient Light sensor (I2C addresses 0x10) (+4k5 code)
// #define USE_MCP9808 // [I2cDriver51] Enable MCP9808 temperature sensor (I2C addresses 0x18 - 0x1F) (+0k9 code)
// #define USE_HP303B // [I2cDriver52] Enable HP303B temperature and pressure sensor (I2C address 0x76 or 0x77) (+6k2 code)
// #define USE_MLX90640 // [I2cDriver53] Enable MLX90640 IR array temperature sensor (I2C address 0x33) (+20k code)
// #define USE_EZOPH // [I2cDriver55] Enable support for EZO's pH sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code)
// #define USE_EZOORP // [I2cDriver55] Enable support for EZO's ORP sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code)
// #define USE_EZORTD // [I2cDriver55] Enable support for EZO's RTD sensor (+0k2 code) - Shared EZO code required for any EZO device (+1k2 code)
// #define USE_EZOHUM // [I2cDriver55] Enable support for EZO's HUM sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code)
// #define USE_EZOEC // [I2cDriver55] Enable support for EZO's EC sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code)
// #define USE_EZOCO2 // [I2cDriver55] Enable support for EZO's CO2 sensor (+0k2 code) - Shared EZO code required for any EZO device (+1k2 code)
// #define USE_EZOO2 // [I2cDriver55] Enable support for EZO's O2 sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code)
// #define USE_EZOPRS // [I2cDriver55] Enable support for EZO's PRS sensor (+0k7 code) - Shared EZO code required for any EZO device (+1k2 code)
// #define USE_EZOFLO // [I2cDriver55] Enable support for EZO's FLO sensor (+0k4 code) - Shared EZO code required for any EZO device (+1k2 code)
// #define USE_EZODO // [I2cDriver55] Enable support for EZO's DO sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code)
// #define USE_EZORGB // [I2cDriver55] Enable support for EZO's RGB sensor (+0k5 code) - Shared EZO code required for any EZO device (+1k2 code)
// #define USE_EZOPMP // [I2cDriver55] Enable support for EZO's PMP sensor (+0k3 code) - Shared EZO code required for any EZO device (+1k2 code)
// #define USE_SEESAW_SOIL // [I2cDriver56] Enable Capacitice Soil Moisture & Temperature Sensor (I2C addresses 0x36 - 0x39) (+1k3 code)
// #define USE_MPU_ACCEL // [I2cDriver58] Enable MPU6886/MPU9250 - found in M5Stack - support both I2C buses on ESP32 (I2C address 0x68) (+2k code)
// #define USE_AM2320 // [I2cDriver60] Enable AM2320 temperature and humidity Sensor (I2C address 0x5C) (+1k code)
2021-07-13 11:01:46 +01:00
// #define USE_T67XX // [I2cDriver61] Enable Telaire T67XX CO2 sensor (I2C address 0x15) (+1k3 code)
// #define USE_HM330X // [I2cDriver63] Enable support for SeedStudio Grove Particule sensor (I2C address 0x40) (+1k5 code)
// #define HM330X_DEFAULT_ADDRESS 0x40 // Option: change default I2C address for HM330X used in SeedSTudio Particucle Sensor
// #define HM330X_WARMUP_DELAY 30 // Option: change warmup delay during which data are not read from sensor after a power up
// #define HM330X_HIDE_OUT_OF_DATE false // Option: change to true to hide data from web GUI and SENSOR while sensor is asleep
// #define USE_HDC2010 // [I2cDriver64] Enable HDC2010 temperature/humidity sensor (I2C address 0x40) (+1k5 code)
// #define USE_DS3502 // [I2CDriver67] Enable DS3502 digital potentiometer (I2C address 0x28 - 0x2B) (+0k4 code)
2022-05-31 13:56:09 +01:00
// #define USE_HYT // [I2CDriver68] Enable HYTxxx temperature and humidity sensor (I2C address 0x28) (+0k5 code)
// #define USE_LUXV30B // [I2CDriver70] Enable RFRobot SEN0390 LuxV30b ambient light sensor (I2C address 0x4A) (+0k5 code)
// #define USE_QMC5883L // [I2CDriver71] Enable QMC5883L magnetic induction sensor (I2C address 0x0D) (+0k8 code)
// #define USE_HMC5883L // [I2CDriver73] Enable HMC5883L magnetic induction sensor (I2C address 0x1E) (+1k3 code)
// #define QMC5883L_TEMP_SHIFT 23 // sensor temperature are not calibrated (only relativ measurement) and need an absolute ground value in °C (see datasheet)
2022-10-10 20:24:20 +01:00
// #define USE_INA3221 // [I2CDriver72] Enable INA3221 3-channel DC voltage and current sensor (I2C address 0x40-0x44) (+3.2k code)
2022-10-09 19:00:34 +01:00
// #define INA3221_ADDRESS1 // allow to change the 1st address to search for INA3221 to 0x41..0x43
// #define INA3221_MAX_COUNT // change the number of devices to search for (default 4).
// // Both settings together allow to limit searching for INA3221 to only a subset of addresses
// #define USE_PMSA003I // [I2cDriver78] Enable PMSA003I Air Quality Sensor (I2C address 0x12) (+1k8 code)
// #define USE_GDK101 // [I2cDriver79] Enable GDK101 sensor (I2C addresses 0x18 - 0x1B) (+1k2 code)
// #define GDK101_SHOW_FW_VERSION
// #define GDK101_SHOW_STATUS
// #define GDK101_SHOW_VIBRATION_STATUS
// #define GDK101_SHOW_MEAS_TIME
// #define USE_TC74 // [I2cDriver80] Enable TC74 sensor (I2C addresses 0x48 - 0x4F) (+1k code)
// #define TC74_MAX_SENSORS 8 // Support non-default/multiple I2C addresses
// #define TC74_I2C_PROBE_ADDRESSES { 0x48, 0x49, 0x4A, 0x4B, 0x4C, 0x4D, 0x4E, 0x4F } // Addresses to probe/support
// #define TC74_MAX_FAILCOUNT 8 // Maximum failed polls before it's marked inactive until reprobing later
// #define USE_PCA9557 // [I2cDriver81] Enable PCA9557 8-bit I/O Expander (I2C addresses 0x18 - 0x1F) (+2k5 code)
2023-07-24 11:29:43 +01:00
// #define USE_MAX17043 // [I2cDriver83] Enable MAX17043 fuel-gauge systems Lipo batteries sensor (I2C address 0x36) (+0k9 code)
// #define MAX17043_ALERT_THRESHOLD 32 // [I2cDriver83] Define the alert threshold for low battery level percentage 1-32
2022-04-16 16:43:10 +01:00
// #define USE_RTC_CHIPS // Enable RTC chip support and NTP server - Select only one
// #define USE_DS3231 // [I2cDriver26] Enable DS3231 RTC (I2C address 0x68) (+1k2 code)
2023-01-24 07:52:43 +00:00
// #define DS3231_ENABLE_TEMP // In DS3231 driver, enable the internal temperature sensor
2022-04-16 16:43:10 +01:00
// #define USE_BM8563 // [I2cDriver59] Enable BM8563 RTC - found in M5Stack - support both I2C buses on ESP32 (I2C address 0x51) (+2.5k code)
// #define USE_PCF85363 // [I2cDriver66] Enable PCF85363 RTC - found Shelly 3EM (I2C address 0x51) (+0k7 code)
2022-11-07 20:03:36 +00:00
// #define USE_DISPLAY // Add I2C/TM1637/MAX7219 Display Support (+2k code)
#define USE_DISPLAY_MODES1TO5 // Enable display mode 1 to 5 in addition to mode 0
#define USE_DISPLAY_LCD // [DisplayModel 1] [I2cDriver3] Enable Lcd display (I2C addresses 0x27 and 0x3F) (+6k code)
#define USE_DISPLAY_SSD1306 // [DisplayModel 2] [I2cDriver4] Enable SSD1306 Oled 128x64 display (I2C addresses 0x3C and 0x3D) (+16k code)
#define USE_DISPLAY_MATRIX // [DisplayModel 3] [I2cDriver5] Enable 8x8 Matrix display (I2C adresseses see below) (+11k code)
#define MTX_ADDRESS1 0x71 // [DisplayAddress1] I2C address of first 8x8 matrix module
#define MTX_ADDRESS2 0x74 // [DisplayAddress2] I2C address of second 8x8 matrix module
#define MTX_ADDRESS3 0x75 // [DisplayAddress3] I2C address of third 8x8 matrix module
#define MTX_ADDRESS4 0x72 // [DisplayAddress4] I2C address of fourth 8x8 matrix module
#define MTX_ADDRESS5 0x73 // [DisplayAddress5] I2C address of fifth 8x8 matrix module
#define MTX_ADDRESS6 0x76 // [DisplayAddress6] I2C address of sixth 8x8 matrix module
#define MTX_ADDRESS7 0x00 // [DisplayAddress7] I2C address of seventh 8x8 matrix module
#define MTX_ADDRESS8 0x00 // [DisplayAddress8] I2C address of eigth 8x8 matrix module
2020-04-10 14:33:10 +01:00
#define USE_DISPLAY_SEVENSEG // [DisplayModel 11] [I2cDriver47] Enable sevenseg display (I2C 0x70-0x77) (<+11k code)
2022-11-07 20:03:36 +00:00
// #define USE_DISPLAY_SEVENSEG_COMMON_ANODE // Enable support for common anode sevenseg displays
// Multiple sevenseg displays are logically arranged vertically with MTX_ADDRESS1 at y=0,
// MTX_ADDRESS2 at y=1, up to MTX_ADDRESS8 at y=7
// Command: DisplayText [yn]8888
// will display 8888 at sevenseg display at I2C address MTX_ADDRESS(n-1)
// Each segment may be address Command: DisplayText [xn]m
// where n is 0..4 (4 digits and middle :) and m is decimal for bitmap of which segment to turn on.
// Reference: https://cdn-learn.adafruit.com/downloads/pdf/adafruit-led-backpack.pdf
// #define SEVENSEG_ADDRESS1 0x70 // No longer used. Use MTX_ADDRESS1 - MTX_ADDRESS8 instead to specify I2C address of sevenseg displays
// #define USE_DISPLAY_SH1106 // [DisplayModel 7] [I2cDriver6] Enable SH1106 Oled 128x64 display (I2C addresses 0x3C and 0x3D)
// #define USE_DISPLAY_TM1650 // [DisplayModel 20] [I2cDriver74] Enable TM1650 display (I2C addresses 0x24 - 0x27 and 0x34 - 0x37)
2022-11-21 13:07:25 +00:00
// #define USE_DT_VARS // Display variables that are exposed in JSON MQTT strings e.g. in TelePeriod messages.
2022-11-07 20:03:36 +00:00
// #define MAX_DT_VARS 16 // Defaults to 7
2022-11-21 13:07:25 +00:00
// #define USE_GRAPH // Enable line charts with displays
// #define NUM_GRAPHS 4 // Max 16
#endif // USE_I2C
2022-11-07 20:03:36 +00:00
// #define USE_DISPLAY // Add I2C/TM1637/MAX7219 Display Support (+2k code)
2022-11-21 13:07:25 +00:00
// #define USE_DISPLAY_TM1637 // [DisplayModel 15] Enable TM1637 Module
// #define USE_DISPLAY_MAX7219 // [DisplayModel 19] Enable MAX7219 Module
2021-05-25 17:53:10 +01:00
// -- Universal Display Driver ---------------------------------
// #define USE_UNIVERSAL_DISPLAY // New universal display driver for both I2C and SPI
2022-11-07 20:03:36 +00:00
#define MAX_TOUCH_BUTTONS 16 // Virtual touch buttons
2021-05-25 17:53:10 +01:00
2018-04-05 14:26:16 +01:00
// -- SPI sensors ---------------------------------
2020-01-02 08:54:58 +00:00
//#define USE_SPI // Hardware SPI using GPIO12(MISO), GPIO13(MOSI) and GPIO14(CLK) in addition to two user selectable GPIOs(CS and DC)
2020-11-30 16:54:40 +00:00
2018-04-05 14:26:16 +01:00
#ifdef USE_SPI
// #define USE_NRF24 // Add SPI support for NRF24L01(+) (+2k6 code)
#define USE_MIBLE // BLE-bridge for some Mijia-BLE-sensors (+4k7 code)
2020-11-30 16:54:40 +00:00
// #define USE_DISPLAY // Add SPI Display support for 320x240 and 480x320 TFT
#define USE_DISPLAY_ILI9341 // [DisplayModel 4] Enable ILI9341 Tft 480x320 display (+19k code)
// #define USE_DISPLAY_EPAPER_29 // [DisplayModel 5] Enable e-paper 2.9 inch display (+19k code)
// #define USE_DISPLAY_EPAPER_42 // [DisplayModel 6] Enable e-paper 4.2 inch display
// #define USE_DISPLAY_SSD1351 // [DisplayModel 9] Enable SSD1351 module
2020-11-30 16:54:40 +00:00
// #define USE_DISPLAY_RA8876 // [DisplayModel 10] [I2cDriver39] (Touch)
// #define USE_DISPLAY_ST7789 // [DisplayModel 12] Enable ST7789 module
2021-01-01 15:05:06 +00:00
// #define USE_DISPLAY_SSD1331 // [DisplayModel 14] Enable SSD1331 module
2020-11-30 16:54:40 +00:00
// #define USE_RC522 // Add support for MFRC522 13.56Mhz Rfid reader (+6k code)
// #define USE_RC522_DATA_FUNCTION // Add support for reading data block content (+0k4 code)
// #define USE_RC522_TYPE_INFORMATION // Add support for showing card type (+0k4 code)
// #define USE_MCP2515 // Add support for can bus using MCP2515 (+7k code)
// #define USE_CANSNIFFER // Add support for can bus sniffer using MCP2515 (+5k code)
2018-04-05 14:26:16 +01:00
#endif // USE_SPI
2023-09-01 20:46:18 +01:00
// -- One wire sensors ----------------------------
// #define USE_HDMI_CEC // Add support for HDMI CEC bus (+7k code, 1456 bytes IRAM)
2023-09-01 20:46:18 +01:00
// -- Serial sensors ------------------------------
//#define USE_MHZ19 // Add support for MH-Z19 CO2 sensor (+2k code)
//#define USE_SENSEAIR // Add support for SenseAir K30, K70 and S8 CO2 sensor (+2k3 code)
//#define USE_CM110x // Add support for CM110x CO2 sensors (+2k7code)
#define CO2_LOW 800 // Below this CO2 value show green light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1)
#define CO2_HIGH 1200 // Above this CO2 value show red light (needs PWM or WS2812 RG(B) led and enable with SetOption18 1)
//#define USE_PMS5003 // Add support for PMS5003 and PMS7003 particle concentration sensor (+1k3 code)
// #define PMS_MODEL_PMS3003 // Enable support of PMS3003 instead of PMS5003/PMS7003 (needs the USE_PMS5003 above)
// #define PMS_MODEL_PMS5003T // Enable support for PMSx003T models that report temperature and humidity (needs the USE_PMS5003 above)
//#define USE_NOVA_SDS // Add support for SDS011 and SDS021 particle concentration sensor (+1k5 code)
#define STARTING_OFFSET 30 // Turn on NovaSDS XX-seconds before tele_period is reached
//#define USE_HPMA // Add support for Honeywell HPMA115S0 particle concentration sensor (+1k4)
//#define USE_SR04 // Add support for HC-SR04 ultrasonic devices (+1k code)
// #define SR04_MAX_SENSOR_DISTANCE 500 // Set sensor max detection distance
//#define USE_ME007 // Add support for ME007 ultrasonic devices (+1k5 code)
// #define ME007_MAX_SENSOR_DISTANCE 800 // Set sensor max detection distance
// #define ME007_ENABLE_MEDIAN_FILTER // Enables that distance measurements are filtered with an median filter of length 5
//#define USE_DYP // Add support for DYP ME-007 ultrasonic distance sensor, serial port version (+0k5 code)
2022-11-19 13:59:36 +00:00
#define USE_SERIAL_BRIDGE // Add support for software Serial Bridge (+2k code)
// #define SERIAL_BRIDGE_BUFFER_SIZE 256 // Serial Bridge receive buffer size (Default ESP8266 = 256, ESP32 = 800)
// #define USE_MODBUS_BRIDGE // Add support for software Modbus Bridge (+4.5k code)
// #define USE_MODBUS_BRIDGE_TCP // Add support for software Modbus TCP Bridge (also enable Modbus TCP Bridge) (+2k code)
// #define MODBUS_BRIDGE_TCP_DEFAULT_PORT 502 // Add support for software Modbus TCP Bridge (start the TCP bridge automatically at PORT 502)
//#define USE_TCP_BRIDGE // Add support for Serial to TCP bridge (+1.3k code)
//#define USE_MP3_PLAYER // Use of the DFPlayer Mini MP3 Player RB-DFR-562 commands: play, pause, stop, track, volume and reset
#define MP3_VOLUME 30 // Set the startup volume on init, the range can be 0..100(max)
// #define USE_DY_SV17F // Use of DY-SV17F MP3 Player commands: play, stop, track and volume
//#define USE_AZ7798 // Add support for AZ-Instrument 7798 CO2 datalogger (+1k6 code)
2022-10-27 23:13:27 +01:00
//#define USE_PN532_HSU // Add support for PN532 using HSU (Serial) interface (+1k7 code, 156 bytes mem)
// #define USE_PN532_DATA_FUNCTION // Add sensor40 command support for erase, setting data block content (+3k code, 32 bytes mem)
//#define USE_RDM6300 // Add support for RDM6300 125kHz RFID Reader (+0k8)
2019-08-25 11:29:48 +01:00
//#define USE_IBEACON // Add support for bluetooth LE passive scan of ibeacon devices (uses HM17 module)
//#define USE_GPS // Add support for GPS and NTP Server for becoming Stratus 1 Time Source (+3k1 code, +132 bytes RAM)
// #define USE_FLOG // Add support for GPS logging in OTA's Flash (Experimental) (+2k9 code, +8 bytes RAM)
//#define USE_HM10 // (ESP8266 only) Add support for HM-10 as a BLE-bridge (+17k code)
//#define USE_HRXL // Add support for MaxBotix HRXL-MaxSonar ultrasonic range finders (+0k7)
//#define USE_TASMOTA_CLIENT // Add support for Arduino Uno/Pro Mini via serial interface including flashing (+2k6 code, 64 mem)
#define USE_TASMOTA_CLIENT_FLASH_SPEED 57600 // Usually 57600 for 3.3V variants and 115200 for 5V variants
#define USE_TASMOTA_CLIENT_SERIAL_SPEED 57600 // Depends on the sketch that is running on the Uno/Pro Mini
2020-05-07 15:03:27 +01:00
//#define USE_OPENTHERM // Add support for OpenTherm (+15k code)
//#define USE_MIEL_HVAC // Add support for Mitsubishi Electric HVAC serial interface (+5k code)
WIP Tuya MCU Bridge driver alternative to the TuyaMCU driver (#17626) * WIP Tuya MCU Bridge driver alternative to the TuyaMCU driver The main difference is this driver does not try and wire MCU data points (Dps) into the tasmota power/light/etc controls. Instead each Dp ends up being relayed directly to MQTT and the rules subsystem. If you want to change the state of something wired up to the MCU, you send tuyamcu specific commands to manipulate the Dp. Each Dp gets a type and id specific topic that is sent to MQTT. eg, Dp id 1 type bool looks like tele/%topic%/TUYAMCUBOOL1. To change state you send a TuyaMCUBool1 command (ie, the command index value is used as the DpId, which is nice and symmetrical) with the new value. Currently Rules operate on TuyaMCU#TypeDpid things, eg, "rule1 on TuyaMCU#Bool1 do power %value% endon" toggle the power on the tasmota device when the state of the thing on the MCU changes too. The most obviously missing stuff at the moment is: - better relaying of the wifi/mqtt status to the MCU - handling wifi reset requests from the MCU - low power stuff? - support for sending status updates and device info queries. - restarting the tuya mcu state machine? - restarting the rx state machine when no bytes are rxed for a period of time - time sync * shorten the log prefix to TYB (3 chars). requested by arendst * use the local definition for the SET_DP command. reaching back to the existing tuyamcu code isnt reliable. pointed out by arendst * put the todo list in the code so it can be tracked * check the wifi/mqtt state every second and update the mcu if it changes. * fix rule processing when Dp state is changed from a cmnd. rule processing was done as part of publishing the state, but publishing the state when it was updated by a command only happened if So59 was set. split rule processing out of publish and call them separately as needed. publish is now called from teleperiod, status updates from the MCU, and from cmnds if so59 is set. rules are called from status updates from the MCU and from cmnds. Co-authored-by: David Gwynne <dlg@defeat.lan.animata.net>
2023-01-08 16:35:45 +00:00
//#define USE_TUYAMCUBR // Add support for TuyaMCU Bridge
//#define USE_PROJECTOR_CTRL // Add support for LCD/DLP Projector serial control interface (+2k code)
// #define USE_PROJECTOR_CTRL_NEC // Use codes for NEC
// #define USE_PROJECTOR_CTRL_OPTOMA // Use codes for OPTOMA
//#define USE_AS608 // Add support for AS608 optical and R503 capacitive fingerprint sensor (+3k code)
// #define USE_AS608_MESSAGES // Add verbose error messages (+0k4 code)
//#define USE_TFMINIPLUS // Add support for TFmini Plus (TFmini, TFmini-S) LiDAR modules via UART interface (+0k8)
//#define USE_HRG15 // Add support for Hydreon RG-15 Solid State Rain sensor (+1k5 code)
2021-08-31 15:41:19 +01:00
//#define USE_VINDRIKTNING // Add support for IKEA VINDRIKTNING particle concentration sensor (+0k6 code)
// #define VINDRIKTNING_SHOW_PM1 // Display undocumented/supposed PM1.0 values
// #define VINDRIKTNING_SHOW_PM10 // Display undocumented/supposed PM10 values
//#define USE_LD2410 // Add support for HLK-LD2410 24GHz smart wave motion sensor (+2k8 code)
//#define USE_LOX_O2 // Add support for LuminOx LOX O2 Sensor (+0k8 code)
//#define USE_GM861 // Add support for GM861 1D and 2D Bar Code Reader (+1k3 code)
2023-05-07 13:11:29 +01:00
// #define GM861_DECODE_AIM // Decode AIM-id (+0k3 code)
2023-05-07 15:01:33 +01:00
// #define GM861_HEARTBEAT // Enable heartbeat (+0k2 code)
// -- Power monitoring sensors --------------------
#define USE_ENERGY_SENSOR // Add support for Energy Monitors (+14k code)
#define USE_ENERGY_MARGIN_DETECTION // Add support for Energy Margin detection (+1k6 code)
#define USE_ENERGY_POWER_LIMIT // Add additional support for Energy Power Limit detection (+1k2 code)
2021-04-06 11:08:07 +01:00
#define USE_ENERGY_DUMMY // Add support for dummy Energy monitor allowing user values (+0k7 code)
#define USE_HLW8012 // Add support for HLW8012, BL0937 or HJL-01 Energy Monitor for Sonoff Pow and WolfBlitz
#define USE_CSE7766 // Add support for CSE7766 Energy Monitor for Sonoff S31 and Pow R2
#define USE_PZEM004T // Add support for PZEM004T Energy monitor (+2k code)
#define USE_PZEM_AC // Add support for PZEM014,016 Energy monitor (+1k1 code)
#define USE_PZEM_DC // Add support for PZEM003,017 Energy monitor (+1k1 code)
#define USE_MCP39F501 // Add support for MCP39F501 Energy monitor as used in Shelly 2 (+3k1 code)
2021-02-14 11:22:08 +00:00
//#define USE_SDM72 // Add support for Eastron SDM72-Modbus energy monitor (+0k3 code)
#define SDM72_SPEED 9600 // SDM72-Modbus RS485 serial speed (default: 9600 baud)
// #define SDM72_IMPEXP // Show additonal import/export active energy and power in MQTT and Web (+0k5 code)
//#define USE_SDM120 // Add support for Eastron SDM120-Modbus energy monitor (+1k1 code)
#define SDM120_SPEED 2400 // SDM120-Modbus RS485 serial speed (default: 2400 baud)
//#define USE_SDM230 // Add support for Eastron SDM230-Modbus energy monitor (+1k6 code)
#define SDM230_SPEED 9600 // SDM230-Modbus RS485 serial speed (default: 9600 baud)
// #define SDM230_MORE_REGS // read more registers (see xnrg_21_sdm230.ino, may cause timing issues (at your own risk, +0k4 code))
//#define USE_SDM630 // Add support for Eastron SDM630-Modbus energy monitor (+0k6 code)
#define SDM630_SPEED 9600 // SDM630-Modbus RS485 serial speed (default: 9600 baud)
2020-10-03 14:06:52 +01:00
// #define SDM630_IMPORT // Show import active energy in MQTT and Web (+0k3 code)
//#define USE_DDS2382 // Add support for Hiking DDS2382 Modbus energy monitor (+0k6 code)
#define DDS2382_SPEED 9600 // Hiking DDS2382 Modbus RS485 serial speed (default: 9600 baud)
//#define USE_DDSU666 // Add support for Chint DDSU666 Modbus energy monitor (+0k6 code)
#define DDSU666_SPEED 9600 // Chint DDSU666 Modbus RS485 serial speed (default: 9600 baud)
//#define USE_SOLAX_X1 // Add support for Solax X1 series Modbus log info (+3k1 code)
#define SOLAXX1_SPEED 9600 // Solax X1 Modbus RS485 serial speed (default: 9600 baud)
// #define SOLAXX1_PV2 // Solax X1 using second PV
//#define USE_LE01MR // Add support for F&F LE-01MR Modbus energy monitor (+1k code)
#define LE01MR_SPEED 9600 // LE-01MR modbus baudrate (default: 9600)
#define LE01MR_ADDR 1 // LE-01MR modbus address (default: 0x01)
#define USE_BL09XX // Add support for various BL09XX Energy monitor as used in Blitzwolf SHP-10 or Sonoff Dual R3 v2 (+1k6 code)
//#define USE_TELEINFO // Add support for Teleinfo via serial RX interface (+5k2 code, +168 RAM + SmartMeter LinkedList Values RAM)
//#define USE_IEM3000 // Add support for Schneider Electric iEM3000-Modbus series energy monitor (+0k8 code)
#define IEM3000_SPEED 19200 // iEM3000-Modbus RS485 serial speed (default: 19200 baud)
#define IEM3000_ADDR 1 // iEM3000-Modbus modbus address (default: 0x01)
2021-08-22 10:47:11 +01:00
// #define IEM3000_IEM3155 // Compatibility fix for Iem3155 (changes Power and Energy total readout)
//#define USE_WE517 // Add support for Orno WE517-Modbus energy monitor (+1k code)
2023-01-02 10:38:08 +00:00
//#define USE_MODBUS_ENERGY // Add support for generic modbus energy monitor using a user file in rule space (+5k)
// -- Low level interface devices -----------------
#define USE_DHT // Add support for DHT11, AM2301 (DHT21, DHT22, AM2302, AM2321) and SI7021 Temperature and Humidity sensor (1k6 code)
//#define USE_MAX31855 // Add support for MAX31855/MAX6675 K-Type thermocouple sensor using softSPI
//#define USE_MAX31865 // Add support for MAX31865 RTD sensors using softSPI
#define MAX31865_PTD_WIRES 2 // PTDs come in several flavors, pick yours. Specific settings per sensor possible with MAX31865_PTD_WIRES1..MAX31865_PTD_WIRES6
#define MAX31865_PTD_RES 100 // Nominal PTD resistance at 0°C (100Ω for a PT100, 1000Ω for a PT1000, YMMV!). Specific settings per sensor possible with MAX31865_PTD_RES1..MAX31865_PTD_RES6
#define MAX31865_REF_RES 430 // Reference resistor (Usually 430Ω for a PT100, 4300Ω for a PT1000). Specific settings per sensor possible with MAX31865_REF_RES1..MAX31865_REF_RES6
#define MAX31865_PTD_BIAS 0 // To calibrate your not-so-good PTD. Specific settings per sensor possible with MAX31865_PTD_BIAS1..MAX31865_PTD_BIAS6
//#define USE_LMT01 // Add support for TI LMT01 temperature sensor, count pulses on single GPIO (+0k5 code)
//#define USE_WIEGAND // Add support for 24/26/32/34 bit RFID Wiegand interface (D0/D1) (+1k7 code)
// -- IR Remote features - all protocols from IRremoteESP8266 --------------------------
// IR Full Protocols mode is now activated through USE_IR_REMOTE_FULL
//
// Code impact of IR full protocols is +90k code, 3k mem
// -- IR Remote features - subset of IR protocols --------------------------
#define USE_IR_REMOTE // Send IR remote commands using library IRremoteESP8266 (+4k3 code, 0k3 mem, 48 iram)
#define IR_SEND_INVERTED false // Invert the output. (default = false) e.g. LED is illuminated when GPIO is LOW rather than HIGH.
// Setting inverted to something other than the default could easily destroy your IR LED if you are overdriving it.
// Unless you REALLY know what you are doing, don't change this.
#define IR_SEND_USE_MODULATION true // Do we do frequency modulation during transmission? i.e. If not, assume a 100% duty cycle.
// ====> IR Full protocols are enabled with the line below
// #define USE_IR_REMOTE_FULL // Support all IR protocols from IRremoteESP8266
//
// WARNING: if you change any IR configuration, you need to clear Platform.io cache
// currently the include change detection does not work for these parameters
// This is not an issue if you compile with gitpod or pre-compiled binaries
// since there is no cache of previously compiled libraries
// ====>
//
// You can also disable specific protocols in user_config_override
// Example: disable some HVAC protocols to reduce flash size
// #define DECODE_WHIRLPOOL_AC false
// #define SEND_WHIRLPOOL_AC false
// #define DECODE_SAMSUNG_AC false
// #define SEND_SAMSUNG_AC false
// ...
// When using 'USE_IR_REMOTE_FULL', parameters below
// (USE_IR_REMOTE, USE_IR_RECEIVE, USE_IR_HVAC...) are IGNORED.
#define USE_IR_SEND_NEC // Support IRsend NEC protocol
#define USE_IR_SEND_RC5 // Support IRsend Philips RC5 protocol
#define USE_IR_SEND_RC6 // Support IRsend Philips RC6 protocol
// Enable IR devoder via GPIO `IR Recv` - always enabled if `USE_IR_REMOTE_FULL`
#define USE_IR_RECEIVE // Support for IR receiver (+7k2 code, 264 iram)
#define IR_RCV_BUFFER_SIZE 100 // Max number of packets allowed in capture buffer (default 100 (*2 bytes ram))
#define IR_RCV_TIMEOUT 15 // Number of milli-Seconds of no-more-data before we consider a message ended (default 15)
#define IR_RCV_MIN_UNKNOWN_SIZE 6 // Set the smallest sized "UNKNOWN" message packets we actually care about (default 6, max 255)
#define IR_RCV_WHILE_SENDING 0 // Turns on receiver while sending messages, i.e. receive your own. This is unreliable and can cause IR timing issues
#define IR_RCV_TOLERANCE 25 // Base tolerance percentage for matching incoming IR messages (default 25, max 100)
2022-04-18 07:59:21 +01:00
// -- SD Card support -----------------------------
// #define USE_SDCARD // mount SD Card, requires configured SPI pins and setting of `SDCard CS` gpio
#define SDC_HIDE_INVISIBLES // hide hidden directories from the SD Card, which prevents crashes when dealing SD created on MacOS
// -- Zigbee interface ----------------------------
2021-11-05 22:21:09 +00:00
//#define USE_ZIGBEE // Enable serial communication with Zigbee CC2530/CC2652 flashed with ZNP or EFR32 flashed with EZSP (+49k code, +3k mem)
#define USE_ZIGBEE_ZNP // Enable ZNP protocol, needed for CC2530/CC2652 based devices
2020-07-29 09:31:38 +01:00
// #define USE_ZIGBEE_EZSP // Enable EZSP protocol, needed for EFR32 EmberZNet based devices, like Sonoff Zigbee bridge
// Note: USE_ZIGBEE_ZNP and USE_ZIGBEE_EZSP are mutually incompatible, you must select exactly one
// #define USE_ZIGBEE_EEPROM // Use the EEPROM from the Sonoff ZBBridge to save Zigbee configuration and data
2020-07-29 09:31:38 +01:00
#define USE_ZIGBEE_CHANNEL 11 // Zigbee Channel (11-26)
#define USE_ZIGBEE_TXRADIO_DBM 20 // Tx Radio power in dBm (only for EZSP, EFR32 can go up to 20 dBm)
#define USE_ZIGBEE_COALESCE_ATTR_TIMER 350 // timer to coalesce attribute values (in ms)
#define USE_ZIGBEE_DEBOUNCE_COMMANDS 200 // if commands are received from the same device/endpoint with same ZCL transaction number, discard packet in this time window (ms)
2020-06-15 19:13:05 +01:00
#define USE_ZIGBEE_MODELID "Tasmota Z2T" // reported "ModelId" (cluster 0000 / attribute 0005)
#define USE_ZIGBEE_MANUFACTURER "Tasmota" // reported "Manufacturer" (cluster 0000 / attribute 0004)
#define USE_ZIGBEE_BATT_REPROBE (24*3600) // Period in seconds during which we don't ask again for battery, default 1 day
#define USE_ZIGBEE_BATT_REPROBE_PAUSE (3600) // Min wait period when sending an autoprobe, default: wait at least 1 hour
#define USE_ZBBRIDGE_TLS // TLS support for zbbridge
#define USE_ZIGBEE_ZBBRIDGE_EEPROM 0x50 // I2C id for the ZBBridge EEPROM
2021-05-22 17:03:58 +01:00
// #define USE_ZIGBEE_FORCE_NO_CHILDREN // This feature forces `CONFIG_MAX_END_DEVICE_CHILDREN` to zero which means that the coordinator does not accept any direct child. End-devices must pair through a router.
// This may mitigate some battery drain issues with IKEA devices.
// **DO NOT USE UNLESS YOU KNOW EXACTLY WHAT YOU'RE DOING** See #10413
2021-01-10 15:04:12 +00:00
// Auto-binding constants, see `Z_autoAttributeReporting`
2021-08-22 21:44:21 +01:00
#define USE_ZIGBEE_AUTOBIND_MAX_ENDPOINTS 8 // max number of endpoint receiving auto-bind requests
#define USE_ZIGBEE_AUTOBIND_MAX_CLUSTER 0x10 // max endpoint number (excluded receiving auto-bind requests)
2021-01-10 15:04:12 +00:00
// Below are the threshold for attribute reporting
#define USE_ZIGBEE_AUTOBIND_BATTVOLTAGE 0.2 // V
#define USE_ZIGBEE_AUTOBIND_BATTPERCENT 5 // %
2021-01-10 15:04:12 +00:00
#define USE_ZIGBEE_AUTOBIND_TEMPERATURE 0.5 // °C
#define USE_ZIGBEE_AUTOBIND_HEATDEMAND 10 // %
#define USE_ZIGBEE_AUTOBIND_PRESSURE 1 // hPA
#define USE_ZIGBEE_AUTOBIND_ILLUMINANCE 5 // lux
#define USE_ZIGBEE_AUTOBIND_HUMIDITY 1.0 // %
#define USE_ZIGBEE_AUTOBIND_LIFT 1.0 // %
2021-01-10 15:04:12 +00:00
// Below are the Max Thresholds for reporting time (in seconds)
#define USE_ZIGBEE_MAXTIME_BATT 4*60*60 // 4h
#define USE_ZIGBEE_MAXTIME_TRV 60*10 // 10m
#define USE_ZIGBEE_MAXTIME_SENSOR 60*60 // 1h
#define USE_ZIGBEE_MAXTIME_LIGHT 60*60 // 1h
#define USE_ZIGBEE_MAXTIME_LIFT 4*60*60 // 4h
2021-01-10 15:04:12 +00:00
2019-10-15 19:00:57 +01:00
// -- Other sensors/drivers -----------------------
2021-12-05 13:49:49 +00:00
//#define USE_SHIFT595 // Add support for 74xx595 8-bit shift registers (+0k7 code)
#define SHIFT595_INVERT_OUTPUTS false // [SetOption133] Don't invert outputs of 74x595 shift register
#define SHIFT595_DEVICE_COUNT 1 // [Shift595DeviceCount] Set the number of connected 74x595 shift registers
//#define USE_TM1638 // Add support for TM1638 switches copying Switch1 .. Switch8 (+1k code)
2023-02-06 15:03:50 +00:00
// #define TM1638_USE_AS_BUTTON // Add support for buttons
// #define TM1638_USE_AS_SWITCH // Add support for switches (default)
// #define TM1638_MAX_DISPLAYS 8 // Add support for power control 8 displays
// #define TM1638_MAX_KEYS 8 // Add support for 8 keys
// #define TM1638_MAX_LEDS 8 // Add support for 8 leds
//#define USE_HX711 // Add support for HX711 load cell (+1k5 code)
// #define USE_HX711_GUI // Add optional web GUI to HX711 as scale (+1k8 code)
// #define HX711_CAL_PRECISION 1 // When HX711 calibration is to course, raise this value
//#define USE_DINGTIAN_RELAY // Add support for the Dingian board using 74'595 et 74'165 shift registers
// #define DINGTIAN_INPUTS_INVERTED // Invert input states (Hi => OFF, Low => ON)
// #define DINGTIAN_USE_AS_BUTTON // Inputs as Tasmota's virtual Buttons
// #define DINGTIAN_USE_AS_SWITCH // Inputs as Tasmota's virtual Switches
// Select none or only one of the below defines
2020-02-29 15:11:59 +00:00
//#define USE_TX20_WIND_SENSOR // Add support for La Crosse TX20 anemometer (+2k6/0k8 code)
//#define USE_TX23_WIND_SENSOR // Add support for La Crosse TX23 anemometer (+2k7/1k code)
2020-05-07 15:03:27 +01:00
//#define USE_WINDMETER // Add support for analog anemometer (+2k2 code)
//#define USE_FTC532 // Add support for FTC532 8-button touch controller (+0k6 code)
//#define USE_RC_SWITCH // Add support for RF transceiver using library RcSwitch (+2k7 code, 460 iram)
//#define USE_RF_SENSOR // Add support for RF sensor receiver (434MHz or 868MHz) (+0k8 code)
// #define USE_THEO_V2 // Add support for decoding Theo V2 sensors as documented on https://sidweb.nl using 434MHz RF sensor receiver (+1k4 code)
// #define USE_ALECTO_V2 // Add support for decoding Alecto V2 sensors like ACH2010, WS3000 and DKW2012 weather stations using 868MHz RF sensor receiver (+1k7 code)
//#define USE_HRE // Add support for Badger HR-E Water Meter (+1k4 code)
2019-10-15 19:49:02 +01:00
//#define USE_A4988_STEPPER // Add support for A4988/DRV8825 stepper-motor-driver-circuit (+10k5 code)
//#define USE_PROMETHEUS // Add support for https://prometheus.io/ metrics exporting over HTTP /metrics endpoint
//#define USE_NEOPOOL // Add support for Sugar Valley NeoPool Controller - also known under brands Hidrolife, Aquascenic, Oxilife, Bionet, Hidroniser, UVScenic, Station, Brilix, Bayrol and Hay (+14k flash, +120 mem)
2021-01-20 12:56:57 +00:00
// #define NEOPOOL_MODBUS_ADDRESS 1 // Any modbus address
//#define USE_FLOWRATEMETER // Add support for water flow meter YF-DN50 and similary (+1k7 code)
2022-04-27 07:20:30 +01:00
// -- Thermostat control ----------------------------
2020-05-10 13:58:38 +01:00
//#define USE_THERMOSTAT // Add support for Thermostat
#define THERMOSTAT_CONTROLLER_OUTPUTS 1 // Number of outputs to be controlled independently
#define THERMOSTAT_SENSOR_NAME "DS18B20" // Name of the local sensor to be used
#define THERMOSTAT_SENSOR_NUMBER 1 // Number of local sensors to be used
#define THERMOSTAT_RELAY_NUMBER 1 // Default output relay number for the first controller (+i for following ones)
#define THERMOSTAT_SWITCH_NUMBER 1 // Default input switch number for the first controller (+i for following ones)
#define THERMOSTAT_TIME_ALLOW_RAMPUP 300 // Default time after last target update to allow ramp-up controller phase in minutes
#define THERMOSTAT_TIME_RAMPUP_MAX 960 // Default time maximum ramp-up controller duration in minutes
#define THERMOSTAT_TIME_RAMPUP_CYCLE 30 // Default time ramp-up cycle in minutes
#define THERMOSTAT_TIME_SENS_LOST 30 // Maximum time w/o sensor update to set it as lost in minutes
#define THERMOSTAT_TEMP_SENS_NUMBER 1 // Default temperature sensor number
#define THERMOSTAT_TIME_MANUAL_TO_AUTO 60 // Default time without input switch active to change from manual to automatic in minutes
#define THERMOSTAT_TIME_RESET 12000 // Default reset time of the PI controller in seconds
#define THERMOSTAT_TIME_PI_CYCLE 30 // Default cycle time for the thermostat controller in minutes
#define THERMOSTAT_TIME_MAX_ACTION 20 // Default maximum thermostat time per cycle in minutes
#define THERMOSTAT_TIME_MIN_ACTION 4 // Default minimum thermostat time per cycle in minutes
#define THERMOSTAT_TIME_MIN_TURNOFF_ACTION 3 // Default minimum turnoff time in minutes, below it the thermostat will be held on
#define THERMOSTAT_PROP_BAND 4 // Default proportional band of the PI controller in degrees celsius
#define THERMOSTAT_TEMP_RESET_ANTI_WINDUP 8 // Default range where reset antiwindup is disabled, in tenths of degrees celsius
#define THERMOSTAT_TEMP_HYSTERESIS 1 // Default range hysteresis for temperature PI controller, in tenths of degrees celsius
#define THERMOSTAT_TEMP_FROST_PROTECT 40 // Default minimum temperature for frost protection, in tenths of degrees celsius
#define THERMOSTAT_TEMP_RAMPUP_DELTA_IN 4 // Default minimum delta temperature to target to get into rampup mode, in tenths of degrees celsius
#define THERMOSTAT_TEMP_RAMPUP_DELTA_OUT 2 // Default minimum delta temperature to target to get out of the rampup mode, in tenths of degrees celsius
#define THERMOSTAT_TEMP_PI_RAMPUP_ACC_E 200 // Default accumulated error when switching from ramp-up controller to PI in hundreths of degrees celsius
#define THERMOSTAT_TIME_OUTPUT_DELAY 180 // Default output delay between state change and real actuation event (f.i. valve open/closed)
#define THERMOSTAT_TEMP_INIT 180 // Default init target temperature for the thermostat controller
#define THERMOSTAT_TIME_MAX_OUTPUT_INCONSIST 3 // Default maximum time where the input and the outpus shall differ (for diagnostic) in minutes
#define THERMOSTAT_TIME_MAX_AUTOTUNE 21600 // Maximum time for the PI autotune function to complete in seconds
#define THERMOSTAT_DUTYCYCLE_AUTOTUNE 35 // Default duty cycle (in % over PI cycle time) for the step response of the autotune PI function
#define THERMOSTAT_PEAKNUMBER_AUTOTUNE 8 // Default number of peak temperatures (max or min) to be used for the autotune PI function
#define THERMOSTAT_TEMP_BAND_NO_PEAK_DET 1 // Default temperature band in thenths of degrees celsius within no peak will be detected
#define THERMOSTAT_TIME_STD_DEV_PEAK_DET_OK 10 // Default standard deviation in minutes of the oscillation periods within the peak detection is successful
2021-01-10 14:47:26 +00:00
// -- PID and Timeprop ------------------------------ // Both together will add +12k1 code
// #define USE_TIMEPROP // Add support for the timeprop feature (+9k1 code)
2021-01-06 22:09:23 +00:00
// For details on the configuration please see the header of tasmota/xdrv_48_timeprop.ino
2021-01-10 14:47:26 +00:00
// #define USE_PID // Add suport for the PID feature (+11k2 code)
2021-01-06 22:09:23 +00:00
// For details on the configuration please see the header of tasmota/xdrv_49_pid.ino
// -- End of general directives ---------------------
2019-10-15 19:03:13 +01:00
2020-06-15 17:36:26 +01:00
/*********************************************************************************************\
* ESP32 only features
\*********************************************************************************************/
#ifdef ESP32
#define SET_ESP32_STACK_SIZE (8 * 1024) // Set the stack size for Tasmota. The default value is 8192 for Arduino, some builds might need to increase it
2022-09-27 14:55:45 +01:00
#ifdef SOC_TOUCH_VERSION_1 // ESP32
#define ESP32_TOUCH_THRESHOLD 40 // [TouchThres] Below this level a touch is detected
#endif
2022-09-27 14:55:45 +01:00
#ifdef SOC_TOUCH_VERSION_2 // ESP32-S2 and ESP32-S3
#define ESP32_TOUCH_THRESHOLD 40000 // [TouchThres] Above this level a touch is detected
#endif
2022-05-04 09:07:24 +01:00
#define USE_ESP32_SENSORS // Add support for ESP32 temperature and optional hall effect sensor
// #define USE_DALI // Add support for DALI
#define DALI_IN_INVERT 0 // DALI RX inverted ?
#define DALI_OUT_INVERT 0 // DALI TX inverted ?
#define DALI_TIMER 0 // ESP32 hardware timer number 0-3 !!! timer 3 used in xdrv_10_scripter.ino !!!
2022-02-20 11:52:02 +00:00
//#define USE_SONOFF_SPM // Add support for ESP32 based Sonoff Smart Stackable Power Meter (+11k code)
//#define USE_DISPLAY_TM1621_SONOFF // Add support for TM1621 dsiplay driver used by Sonoff POWR3xxD and THR3xxD
2021-12-01 10:21:56 +00:00
2022-02-20 11:52:02 +00:00
//#define USE_ETHERNET // Add support for ethernet (+20k code)
// #define USE_WT32_ETH01 // Add support for Wireless-Tag WT32-ETH01
// #define ETH_TYPE 0 // [EthType] 0 = ETH_PHY_LAN8720, 1 = ETH_PHY_TLK110/ETH_PHY_IP101, 2 = ETH_PHY_RTL8201, 3 = ETH_PHY_DP83848, 4 = ETH_PHY_DM9051, 5 = ETH_PHY_KSZ8081
2021-02-02 17:02:24 +00:00
// #define ETH_ADDRESS 1 // [EthAddress] 0 = PHY0 .. 31 = PHY31
// #define ETH_CLKMODE 0 // [EthClockMode] 0 = ETH_CLOCK_GPIO0_IN, 1 = ETH_CLOCK_GPIO0_OUT, 2 = ETH_CLOCK_GPIO16_OUT, 3 = ETH_CLOCK_GPIO17_OUT
// Olimex ESP32-PoE
#define ETH_TYPE 0 // [EthType] 0 = ETH_PHY_LAN8720, 1 = ETH_PHY_TLK110/ETH_PHY_IP101, 2 = ETH_PHY_RTL8201, 3 = ETH_PHY_DP83848, 4 = ETH_PHY_DM9051, 5 = ETH_PHY_KSZ8081
2021-02-02 17:02:24 +00:00
#define ETH_ADDRESS 0 // [EthAddress] 0 = PHY0 .. 31 = PHY31
#define ETH_CLKMODE 3 // [EthClockMode] 0 = ETH_CLOCK_GPIO0_IN, 1 = ETH_CLOCK_GPIO0_OUT, 2 = ETH_CLOCK_GPIO16_OUT, 3 = ETH_CLOCK_GPIO17_OUT
2020-06-17 14:27:12 +01:00
// wESP32-PoE
// #define ETH_TYPE 0 // [EthType] 0 = ETH_PHY_LAN8720, 1 = ETH_PHY_TLK110/ETH_PHY_IP101, 2 = ETH_PHY_RTL8201, 3 = ETH_PHY_DP83848, 4 = ETH_PHY_DM9051, 5 = ETH_PHY_KSZ8081
2021-02-02 17:02:24 +00:00
// #define ETH_ADDRESS 0 // [EthAddress] 0 = PHY0 .. 31 = PHY31
2020-06-17 14:27:12 +01:00
// #define ETH_CLKMODE 0 // [EthClockMode] 0 = ETH_CLOCK_GPIO0_IN, 1 = ETH_CLOCK_GPIO0_OUT, 2 = ETH_CLOCK_GPIO16_OUT, 3 = ETH_CLOCK_GPIO17_OUT
#define USE_ADC // Add support for ADC on GPIO32 to GPIO39
#define USE_NETWORK_LIGHT_SCHEMES // Add support for light schemes via DDP (via UDP on port 4048)
//#define USE_SPI // Add support for hardware SPI
2021-02-14 11:22:08 +00:00
//#define USE_MI_ESP32 // Add support for ESP32 as a BLE-bridge (+9k2 mem, +292k flash)
//#define USE_BLE_ESP32 // Add support for ESP32 as a BLE-bridge (+9k2? mem, +292k? flash)
2022-04-16 18:50:05 +01:00
//#define BLE_ESP32_ENABLE false // [SetOption115] Default value for SetOption115
//#define USE_IBEACON // Add support for Bluetooth LE passive scan of iBeacon devices (uses HM17 module)
//#define USE_IBEACON_ESP32 // Add support for Bluetooth LE passive scan of iBeacon devices using the internal ESP32 Bluetooth module
//#define USE_WEBCAM // Add support for webcam
2020-06-15 17:36:26 +01:00
2022-01-08 22:16:11 +00:00
#define USE_AUTOCONF // Enable Esp32 autoconf feature, requires USE_BERRY and USE_WEBCLIENT_HTTPS (12KB Flash)
2021-03-31 11:49:16 +01:00
#define USE_BERRY // Enable Berry scripting language
#define USE_BERRY_PYTHON_COMPAT // Enable by default `import python_compat`
2021-10-19 19:14:31 +01:00
#define USE_BERRY_TIMEOUT 4000 // Timeout in ms, will raise an exception if running time exceeds this timeout
2021-09-04 14:07:03 +01:00
#define USE_BERRY_PSRAM // Allocate Berry memory in PSRAM if PSRAM is connected - this might be slightly slower but leaves main memory intact
#define USE_BERRY_IRAM // Allocate some data structures in IRAM (which is ususally unused) when possible and if no PSRAM is available
#define USE_BERRY_FAST_LOOP_SLEEP_MS 5 // Minimum time in milliseconds to before calling again `tasmota.fast_loop()`, a smaller value will consume more CPU (min 1ms)
// #define USE_BERRY_DEBUG // Compile Berry bytecode with line number information, makes exceptions easier to debug. Adds +8% of memory consumption for compiled code
2022-11-03 21:01:24 +00:00
// #define UBE_BERRY_DEBUG_GC // Print low-level GC metrics
2022-03-21 18:35:57 +00:00
// #define USE_BERRY_INT64 // Add 64 bits integer support (+1.7KB Flash)
#define USE_WEBCLIENT // Enable `webclient` to make HTTP/HTTPS requests. Can be disabled for security reasons.
2021-09-03 07:16:08 +01:00
// #define USE_WEBCLIENT_HTTPS // Enable HTTPS outgoing requests based on BearSSL (much ligher then mbedTLS, 42KB vs 150KB) in insecure mode (no verification of server's certificate)
// Note that only one cipher is enabled: ECDHE_RSA_WITH_AES_128_GCM_SHA256 which is very commonly used and highly secure
#define USE_BERRY_WEBCLIENT_USERAGENT "TasmotaClient" // default user-agent used, can be changed with `wc.set_useragent()`
2021-10-11 18:10:37 +01:00
#define USE_BERRY_WEBCLIENT_TIMEOUT 2000 // Default timeout in milliseconds
//#define USE_BERRY_PARTITION_WIZARD // Add a button to dynamically load the Partion Wizard from a bec file online (+1.3KB Flash)
#define USE_BERRY_PARTITION_WIZARD_URL "http://ota.tasmota.com/tapp/partition_wizard.bec"
//#define USE_BERRY_GPIOVIEWER // Add a button to dynamocally load the GPIO Viewer from a bec file online
#define USE_BERRY_GPIOVIEWER_URL "http://ota.tasmota.com/tapp/gpioviewer.bec"
2022-07-18 10:26:05 +01:00
#define USE_BERRY_TCPSERVER // Enable TCP socket server (+0.6k)
// #define USE_BERRY_ULP // Enable ULP (Ultra Low Power) support (+4.9k)
// Berry crypto extensions below:
#define USE_BERRY_CRYPTO_AES_GCM // enable AES GCM 256 bits
// #define USE_BERRY_CRYPTO_AES_CCM // enable AES CCM 128 bits
// #define USE_BERRY_CRYPTO_AES_CTR // enable AES CTR 256 bits
// #define USE_BERRY_CRYPTO_EC_P256 // enable EC P256r1
// #define USE_BERRY_CRYPTO_EC_C25519 // enable Elliptic Curve C C25519
#define USE_BERRY_CRYPTO_SHA256 // enable SHA256 hash function
#define USE_BERRY_CRYPTO_HMAC_SHA256 // enable HMAC SHA256 hash function
// #define USE_BERRY_CRYPTO_PBKDF2_HMAC_SHA256 // PBKDF2 with HMAC SHA256, used in Matter protocol
2022-12-23 17:31:19 +00:00
// #define USE_BERRY_CRYPTO_HKDF_SHA256 // HKDF with HMAC SHA256, used in Matter protocol
// #define USE_BERRY_CRYPTO_SPAKE2P_MATTER // SPAKE2+ used in Matter 1.0, complete name is SPAKE2+-P256-SHA256-HKDF-SHA256-HMAC-SHA256
// #define USE_BERRY_CRYPTO_RSA // RSA primitives including JWT RS256 (3.9KB flash)
2021-03-03 11:44:09 +00:00
#define USE_CSE7761 // Add support for CSE7761 Energy monitor as used in Sonoff Dual R3
// -- LVGL Graphics Library ---------------------------------
2021-05-21 21:31:15 +01:00
//#define USE_LVGL // LVGL Engine, requires Berry (+382KB)
#define USE_LVGL_PSRAM // Allocate LVGL memory in PSRAM if PSRAM is connected - this might be slightly slower but leaves main memory intact
2022-05-20 20:29:39 +01:00
// #define USE_LVGL_HASPMOTA // Enable OpenHASP compatiblity and Robotocondensed fonts (+90KB flash)
#define USE_LVGL_MAX_SLEEP 10 // max sleep in ms when LVGL is enabled, more than 10ms will make display less responsive
2021-05-21 21:31:15 +01:00
#define USE_LVGL_PNG_DECODER // include a PNG image decoder from file system (+16KB)
//#define USE_LVGL_TOUCHSCREEN // Use virtual touch screen with Berry driver
2021-05-21 21:31:15 +01:00
//#define USE_LVGL_FREETYPE // Use the FreeType renderer to display fonts using native TTF files in file system (+77KB flash)
#define LV_USE_FT_CACHE_MANAGER 1 // define whether glyphs are cached by FreeType library
#define USE_LVGL_FREETYPE_MAX_FACES 64 // max number of FreeType faces in cache
#define USE_LVGL_FREETYPE_MAX_SIZES 4 // max number of sizes in cache
#define USE_LVGL_FREETYPE_MAX_BYTES 16*1024 // max bytes in cache
2021-05-20 18:34:51 +01:00
#define USE_LVGL_FREETYPE_MAX_BYTES_PSRAM 64*1024 // max bytes in cache when using PSRAM
#define USE_LVGL_BG_DEFAULT 0x000000 // Default color for the uninitialized background screen (black)
2021-05-21 21:31:15 +01:00
// Disabling select widgets that will be rarely used in Tasmota (-13KB)
// Main widgets as defined in LVGL8
#define BE_LV_WIDGET_ARC
#define BE_LV_WIDGET_BAR
#define BE_LV_WIDGET_BTN
#define BE_LV_WIDGET_BTNMATRIX
#define BE_LV_WIDGET_CANVAS
#define BE_LV_WIDGET_CHECKBOX
#define BE_LV_WIDGET_DROPDOWN
#define BE_LV_WIDGET_IMG
#define BE_LV_WIDGET_LABEL
#define BE_LV_WIDGET_LINE
#define BE_LV_WIDGET_ROLLER
#define BE_LV_WIDGET_SLIDER
#define BE_LV_WIDGET_SWITCH
#define BE_LV_WIDGET_TABLE
#define BE_LV_WIDGET_TEXTAREA
#define BE_LV_WIDGET_CHART
#define BE_LV_WIDGET_COLORWHEEL
#define BE_LV_WIDGET_IMGBTN
#define BE_LV_WIDGET_LED
#define BE_LV_WIDGET_METER
#define BE_LV_WIDGET_MSGBOX
#define BE_LV_WIDGET_SPINBOX
2021-10-25 21:20:48 +01:00
#define BE_LV_WIDGET_SPINNER
// #define BE_LV_WIDGET_KEYBOARD
// #define BE_LV_WIDGET_TABVIEW
// #define BE_LV_WIDGET_TILEVIEW
// #define BE_LV_WIDGET_LIST
#define BE_LV_WIDGET_QRCODE
2022-05-04 09:07:24 +01:00
2020-11-28 11:46:17 +00:00
#endif // ESP32
2020-06-15 17:36:26 +01:00
/*********************************************************************************************\
* Debug features
\*********************************************************************************************/
//#define DEBUG_TASMOTA_CORE // Enable core debug messages
//#define DEBUG_TASMOTA_DRIVER // Enable driver debug messages
//#define DEBUG_TASMOTA_SENSOR // Enable sensor debug messages
//#define USE_DEBUG_DRIVER // Use xdrv_99_debug.ino providing commands CpuChk, CfgXor, CfgDump, CfgPeek and CfgPoke
2021-11-03 09:42:30 +00:00
/*********************************************************************************************\
* Profiling features
\*********************************************************************************************/
//#define USE_PROFILING // Enable profiling
//#define PROFILE_THRESHOLD 70 // Minimum duration in milliseconds to start logging
//#define USE_PROFILE_DRIVER // Enable driver profiling
//#define USE_PROFILE_FUNCTION // Enable driver function profiling
/*********************************************************************************************\
2018-08-31 13:47:49 +01:00
* Optional firmware configurations
2020-04-10 09:52:22 +01:00
* Select none or just one for optional features and sensors as configured in tasmota_configurations.h
2018-08-31 13:47:49 +01:00
* See RELEASENOTES.md for selected features
\*********************************************************************************************/
//#define FIRMWARE_LITE // Create tasmota-lite with no sensors
//#define FIRMWARE_SENSORS // Create tasmota-sensors with useful sensors enabled
//#define FIRMWARE_KNX_NO_EMULATION // Create tasmota-knx with KNX but without Emulation
//#define FIRMWARE_DISPLAYS // Create tasmota-display with display drivers enabled
//#define FIRMWARE_IR // Create tasmota-ir with IR full protocols activated, and many sensors disabled
//#define FIRMWARE_MINIMAL // Create tasmota-minimal as intermediate firmware for OTA-MAGIC
2023-02-20 21:36:34 +00:00
/*********************************************************************************************\
* Safe guard when needed defines are not done in Platformio *
\*********************************************************************************************/
#ifndef OTA_URL
2023-03-03 11:34:20 +00:00
#define OTA_URL ""
2023-02-20 21:36:34 +00:00
#endif
2017-01-28 13:41:01 +00:00
/*********************************************************************************************\
* User configurable items override *
\*********************************************************************************************/
#ifdef USE_CONFIG_OVERRIDE
2022-06-21 15:53:58 +01:00
#include "user_config_override.h" // Configuration overrides for my_user_config.h
#endif
/*********************************************************************************************\
* Post-process obsoletes
\*********************************************************************************************/
#ifdef USE_ESP32MAIL
#define USE_SENDMAIL // USE_ESP32MAIL is replaced by USE_SENDMAIL
#endif
/*********************************************************************************************\
* Mutual exclude options
2017-01-28 13:41:01 +00:00
\*********************************************************************************************/
2022-11-23 20:41:35 +00:00
#if defined(ESP8266) && defined(USE_DISCOVERY) && (defined(USE_MQTT_AWS_IOT) || defined(USE_MQTT_AWS_IOT_LIGHT))
2019-06-05 10:44:52 +01:00
#error "Select either USE_DISCOVERY or USE_MQTT_AWS_IOT, mDNS takes too much code space and is not needed for AWS IoT"
#endif
#if defined(USE_RULES) && defined(USE_SCRIPT)
#error "Select either USE_RULES or USE_SCRIPT. They can't both be used at the same time"
#endif
/*********************************************************************************************\
* Post-process compile options for Autoconf and others
\*********************************************************************************************/
#if defined(USE_AUTOCONF)
#ifndef USE_BERRY
#define USE_BERRY
#endif
#ifndef USE_WEBCLIENT_HTTPS
#define USE_WEBCLIENT_HTTPS
#endif
#ifndef USE_MQTT_TLS
#define USE_MQTT_TLS
#endif
#endif // USE_AUTOCONF
#ifdef USE_SONOFF_SPM
#define USE_ETHERNET
#endif
/*********************************************************************************************\
* Post-process compile options for TLS
\*********************************************************************************************/
2022-06-21 15:53:58 +01:00
#ifdef ESP8266
#ifdef USE_SENDMAIL
#define USE_TLS // flag indicates we need to include TLS code
#endif
#endif
#if defined(USE_MQTT_TLS) || defined(USE_TELEGRAM) || defined(USE_WEBCLIENT_HTTPS)
2022-06-21 15:53:58 +01:00
#define USE_TLS // flag indicates we need to include TLS code
#endif
2022-01-13 18:32:16 +00:00
/*********************************************************************************************\
* Post-process stack size adjustment
\*********************************************************************************************/
#if defined(USE_LVGL) && defined(USE_LVGL_FREETYPE) // Freetype requires a stack of at least 24KB
#if SET_ESP32_STACK_SIZE < (24 * 1024)
#undef SET_ESP32_STACK_SIZE
#define SET_ESP32_STACK_SIZE (24 * 1024)
#endif
#endif // USE_LVGL && USE_LVGL_FREETYPE
#endif // _MY_USER_CONFIG_H_