Tasmota

Module is a firmware supported device which has specific code to enable its features.

New Modules are added to Tasmota only if a device requires additional code for new functions. Use Templates first to configure your device if it's not in the module list.

Configure Module page in the WebUI is used to configure your device as one of the modules and to configure additional components connected to one of the free GPIO pins of the device.

Use Generic module (Module 18) to have almost all GPIO pins available.

Each module is assigned a number which is used in Template configuration or when using Module command.

#	Name	Module specifics
0	Template	Module for currently active template. Named after the template NAME field. If a template is not active it will display `Generic (0)`. Do not use it until you enter a template, use `Generic (18)`
1	Sonoff Basic
2	Sonoff RF
3	Sonoff SV
4	Sonoff TH
5	Sonoff Dual	Process relay and button via hardware serial interface using GPIO01 and GPIO03. Change the baud rate to 19200 bps. Process buttons as single press only
6	Sonoff POW
7	Sonoff 4Ch
8	Sonoff S2X
9	Slampher
10	Sonoff Touch	Invert `LedState 1` functionality
11	Sonoff LED	Set light type to 2 PWM channels disregarding SetOption15. Fix device specific LED instabilities by disabling GPIO04, GPIO5 and GPIO14
12	1 Channel
13	4 Channel	See Sonoff Dual
14	Motor C/AC	Force all relays ON at power up and disable command `PowerOnState`
15	ElectroDragon
16	EXS Relay(s)	Enable pulse latching using even/odd numbered relay pairs
17	WION
18	Generic	Show Wemos specific pin information in GUI
19	Sonoff Dev
20	H801	Change hardware UART Tx from GPIO01 to GPIO02
21	Sonoff SC	Enable and process data via hardware serial interface using GPIO01 and GPIO03. Change the baud rate to 19200 bps
22	Sonoff BN-SZ	Set light type to 1 PWM channel disregarding `SetOption15`
23	Sonoff 4Ch Pro	Button handling disregarding `SetOption13` only allowing single press to enable RF learning while holding the button
24	Huafan SS
25	Sonoff Bridge	Enable and Process data via hardware serial interface using GPIO01 and GPIO03. Change the baud rate to 19200 bps. Process 16 buttons in web GUI. Enable EFM8BB1 firmware upload
26	Sonoff B1	Set light type to RGBWC using MY92x1
27	Ailight	Set light type to RGBW using MY92x1
28	Sonoff T1 1Ch	See Sonoff Touch
29	Sonoff T1 2Ch	See Sonoff Touch
30	Sonoff T1 3Ch	See Sonoff Touch
31	Supla Espablo
32	Witty Cloud
33	Yunshan Relay
34	MagicHome
35	Luani HVIO
36	KMC 70011
37	Arilux LC01
38	Arilux LC11
39	Sonoff Dual R2	Process buttons as single press only
40	Arilux LC06
41	Sonoff S31	Selects component types for the CSE7766 (serial connected energy monitoring chip) with Rx and Tx hardware serial (even parity) on GPIO01 and GPIO03 respectively. Sets serial interface to 4800 baud and disables serial logging
42	Zengge WF017
43	Sonoff Pow R2
44	Sonoff IFan02	Enable command `FanSpeed`. Disable `Interlock` and `PulseTime`. Tune status information, MQTT data and GUI. Sync with microcontroller. Process Domoticz Fan state
45	Blitzwolf SHP	Module specific power monitoring calibration
46	Shelly 1
47	Shelly 2
48	Xiaomi Philips	Process color temperature using PWM2 and intensity using PWM1
49	Neo Coolcam
50	ESP SwitCh
51	Obi Socket
52	Teckin
53	APLIC WDP303075
54	TuyaMCU	Enable and process data via software or hardware serial interface using component 107 and 108. Change the baud rate to 9600 bps. Process all buttons
55	Gosund SP1 v23
56	Armtronix Dimmers	Enable and process data via software or hardware serial interface using component 148 and 149. Change baudrate to 115200 bps.
57	SK03 Outdoor (Tuya)
58	PS-16-DZ	Enable and process data via software or hardware serial interface using component 148 and 149. Change the baud rate to 19200 bps.
59	Teckin US
60	Manzoku Strip (EU 4)
61	Obi Socket 2
62	YTF LR Bridge	Disable serial interface to stop loopback
63	Digoo DG-SP202
64	KA10
65	Luminea ZX2820
66	Mi Desk Lamp	Process rotary and `Button1` data specific to this device
67	SP10
68	WAGA CHCZ02MB
69	SYF05
70	Sonoff L1
71	Sonoff iFan03
72	EX-Store Dimmer

Serial logging is disabled by the Tasmota code for several modules and components (e.g., Sonoff POW, Sonoff S31, Sonoff Dual (v1), Tuya dimmers, PZEM components, etc.). Serial communication is used by these devices to transfer the data from the MCU chip to the ESP chip. Do not enable serial logging (SerialLog 0) on these devices. It can cause the device software to crash.

Wiki has moved to link on the left.